Service bulletin 1801317
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
| Type | Service bulletin |
|---|---|
| NHTSA id | 10224933 |
| Published by NHTSA | 2022-10-31 |
| Manufacturer's number | 1801317 |
| Manufacturer's date | 2017-10-11 |
| NHTSA component | WHEELS; STEERING; BACK OVER PREVENTION; SERVICE BRAKES; POWER TRAIN; EXTERIOR LIGHTING; ELECTRICAL SYSTEM; STRUCTURE |
NHTSA's summary
Flash: Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with thelatest available software. The customer may experience a Malfunction Indicator Lamp (MIL) illumination or notice the engine being too quick to shut down when coming to astop in Electric Stop Start (ESS) mode. Upon further investigation the technician may find the following DTCs set in the PCM memory:P0556 - Brake Booster Pressure Sensor Circuit Performance. U0428 - Implausible Data Received From Steering Angle Sensor Module. U1504 - Implausible Message Data Length Received From Steering Angle Sensor. C0501 - Left Front Wheel Speed Sensor Range/Performance. C0507 - Right Front Wheel Speed Sensor Range/Performance. C050D - Left Rear Wheel Speed Sensor Range/Performance. C0513 - Right Rear Wheel Speed Sensor Range/Performance. Erroneously set Wheel Speed Sensor DTCs listed above will not turn on the MIL by design but may be found during a vehiclediagnostic scan.Some customers may also experience the following condition:During an engine limp mode condition, the transmission remains in a fixedgear. In addition the following enhancements are included:Calibration update to allow the throttle body to be cycled while the engine isoff, for diagnostic purposes. Calibration update for ESS to allow the engine to remain running during a briefstop.
The document
The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.
Components
Body and frame, Brakes, Driver assistance, Electrical system, Lighting, Steering, Transmission and driveline, Wheels, Backup camera
Trouble codes named
C0501, C0507, C050D, C0513, P0556, U0428, U1504
| JEEP CHEROKEE | 2017 |
|---|
Listing a model year does not mean every vehicle of it is concerned: the document says which.
| 9003357 | 2024-01-02. Service bulletin. ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA. |
|---|---|
| 2101721 | 2023-01-17. Service bulletin. Power Transfer Unit (PTU) Broken Input Spline - X89 Warranty Extension This bulletin involves replacing the PTU assembly with an updated part. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set: P1720-00 - Output Speed Sensor-Wheel Speed Rationality. P215C-00 - Output Shaft Speed Wheel Speed Correlation. The customer may also describe one or more of the following: Grinding noise coming from under the vehicle while driving. Vehicle will not move. |
| 0805317 | 2022-10-31. Service bulletin. RA3 and RA4 Radio Enhancements This bulletin involves inspecting and if required, updating the radio software. Customers may experience one or more of the following:Radio functions/touchscreen locks up (does not affect backup camera). Phone presets do not save. ?Navigation Failed? message is displayed. Navigation is inoperative or inaccurate. CD player will not play songs and/or locks up the radio. Clock will not automatically update to local time. Clock may be off by several hours. (RA3 only). Poor or no connection to cellular network. ?Charge Complete? notification is not received (RU PHEV only). Some Uconnect® App remote commands do not execute with the vehicle. Radio Apps are inoperative. Radio display screen is black or blank. Battery drain - due to radio staying on. Navigation failed message is displayed. Clock not automatically updating to local time. Improvements:Auto Play can now be configured. Media devices, Phone pairing and Bluetooth® usage improvements. Add the ability to drag and drop icons into the menu bar. Adds ?Do Not Disturb? text message feature. Fix for radio locks up/frozen. Fix for radio loses time. Enhanced Voice recognition (VR) performance. Media devices, phone pairing and Bluetooth usage improvements. Improved tuner performance. Human Machine Interface (HMI) improvements. Satellite radio reception improvements. |
| 2101721 | 2022-10-17. Service bulletin. Power Transfer Unit (PTU) Broken Input Spline - X89 Warranty Extension This bulletin involves replacing the PTU assembly with an updated part. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set: P1720-00 - Output Speed Sensor-Wheel Speed Rationality. P215C-00 - Output Shaft Speed Wheel Speed Correlation. The customer may also describe one or more of the following: Grinding noise coming from under the vehicle while driving. Vehicle will not move. |
| 2101721RevA | 2022-10-17. Service bulletin. Power Transfer Unit (PTU) Broken Input Spline - X89 Warranty Extension This bulletin involves replacing the PTU assembly with an updated part. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set: P1720-00 - Output Speed Sensor-Wheel Speed Rationality. P215C-00 - Output Shaft Speed Wheel Speed Correlation. The customer may also describe one or more of the following:Grinding noise coming from under the vehicle while driving. Vehicle will not move. |
| 9003825 | 2022-09-15. Service bulletin. LATCH, Hood For the following concerns, please verify secondary plunger switch before replacing hood latch with primary switch. Please refer to service information for complete diagnostics of the secondary plunger switch which is located in the left front under hood on RU, MP, and WK/WD and left rear under hood on KL. 1) Electronic Stop Start Message on Cluster or DTC P152F without hood ajar illuminated. 2) KL Hood ajar light is on or unlatched hood due to high closing effort. (KL hood may have a higher closing effort to latch the hood as rubber bumper interference is set purposely high to prevent hood flutter at highway speeds) If stop start message or DTC P152F is present on vehicles without a hood ajar light illuminated, the issue is not related to the primary hood latch switch. |
| 9004401 | 2022-08-22. Service bulletin. DIFFERENTIAL, Rear Axle (KL 4WD w/DK2 = 1-SPEED RDM) The Differential, Rear Axle (aka RDM) design, pump design, Driveline Control Module (aka DLCM) hardware & software and pressure sensor have all changed in the past few years. The changes are not interchangeable and each had a separate implementation date. Please comprehend it to avoid repeat repairs. There are 2 sections each with 3 sub-sections: 1) For 2014/5 VINs with DK2 = 1-spd RDM 2) For 2016 and later VINs with DK2 = 1-spd RDM 1) For 2014/5 VINs with DK2 = 1-spd RDM 2014 - 2015 VINs were built with a 1-speed RDM used a 24 plate clutch design. New service RDMs 68550586A$ use a 20-plate design. 1.1) If replacing the RDM · 24 plate and 20-plate design RDMs are NOT interchangeable unless the Drive Line Control Module (DLCM) is also replaced. · 68550586A$ service RDMs have a 20 clutch plate design · Not all 20-plate RDMs have the new pump design. The new pump requires a new DLCM. · All new service RDMs are shipped with the new pump design. · If a new 68550586AA service RDMs is installed, then replace the DLCM with new DLCM 68540647AA - 1-spd designed for the 20-plate RDM. 1.2) If replacing the DLCM but not the RDM or pump assembly, then · If the RDM is the original 24 plate design then use 68540645AA - 1-spd, 24 plate DLCM AND replace the pump with 68551790AA · If the RDM is the new 20 plate design then use 68540647AA - 1-spd, 20 plate DLCM AND also replace the pump with 68551790AA new pump unless the RDM previously had a 68551790AA installed. 1.3) If replacing the pump assembly, then use 68551790AA (new pump) AND also replace the DLCM with the version that matches the correct version of the RDM (24 or 20 plate). · Use 68540645AA for the 24 plate RDM with a new pump. · Use 68540647AA for the 20 plate RDM with a new pump. 2) For 2016 and later VINs with DK2 = 1-spd RDM Early 2016 were built with 68090612AG 24 plate RDMs. Use Section 1 ?For 2014/5 VINs with DK2 = 1-spd RDM? to resolve. The balance of M |
| 9004402 | 2022-08-22. Service bulletin. DIFFERENTIAL, Rear Axle (KL 4WD w/DK4 = 2-SPEED RDM) The Differential, Rear Axle (aka RDM) design, pump design, Driveline Control Module (aka DLCM) hardware & software and pressure sensor have all changed in the past few years. The chages are not interchangeable and each had a separate implementation date. Please comprehend it to avoid repeat repairs. There are 2 sections each with 3 sub-sections: 1) For 2014/5 VINs with DK2 = 1-spd RDM 2) For 2016 and later VINs with DK2 = 1-spd RDM 1) For 2014/5 VINs with DK4 = 2-spd RDM 2014 - 2015 VINs built with a 2-speed RDM used a 24 plate clutch design. Service RDMs (DK4: 68545100AA and DK4 + AWL: 68545101AA) have a 20-plate design. 1.1) If replacing the RDM · 24-plate and 20-plate design RDMs are NOT interchangeable unless the Drive Line Control Module (DLCM) is also replaced. · Both 68545100A$ and 68545101A$ service RDMs have a 20 clutch plate design · Not all 20 plate RDMs have the new pump design. The new pump requires a new DLCM. · All new service RDMs are shipped with the new pump design. · If a new 20 plate service RDM is installed, then replace the DLCM with new DLCM 68383660AE - 2-spd designed for the 20 plate RDM. 1.2) If replacing the DLCM but not the RDM or pump assembly, then · If the RDM is the original 24 plate design then use 68540646AA - 2-spd, 24 plate DLCM AND also replace the pump with 68551790AA new pump. · If the RDM is the new 20 plate design then use 68383660AE - 2-spd, 20 plate DLCM AND also replace the pump with 68551790AA new pump unless the RDM previously had a 68551790AA installed. 1.3) If replacing the pump assembly, then use 68551790AA (new pump) AND also replace the DLCM with the version that matches the correct version of the RDM (24 or 20 plate). · Use 68540646AA for the 24-plate RDM with a new pump. · Use 68383660AE for the 20-plate RDM with a new pump. 2) Early 2016 were built with 24 plate RDMs. These include p/n?s 68090615AJ (2spd std), and 52123642AJ (2spd locker). Use Secti |
| W84 Combo Phase1 | 2022-07-18. Service bulletin. Customer Satisfaction Notification W84 Powertrain Software Update |