WenmarOpen by Wenmar Pro

Service bulletin 0100116

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
TypeService bulletin
NHTSA id10213329
Published by NHTSA2022-06-06
Manufacturer's number0100116
Manufacturer's date2016-02-05
NHTSA componentELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING

NHTSA's summary

Engine Start /Stop Procedure with room fuse removed

The document

The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.

Components

Electrical system, Engine

Vehicles listed
MAZDA CX-32016
MAZDA CX-52013, 2014, 2015, 2016
MAZDA CX-72007, 2008, 2009, 2010, 2011, 2012
MAZDA CX-72013
MAZDA CX-92007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016
MAZDA CX92007
MAZDA MAZDA22011, 2012, 2013, 2014, 2015, 2016
MAZDA MAZDA32005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016
MAZDA MAZDA52006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015
MAZDA MAZDA52016
MAZDA MAZDA62005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016
MAZDA MX-52006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016
MAZDA MX-5 MIATA2005 (the catalog's model; the bulletin names a series or trim of it)

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Recalls for the same vehicles and component
20174272017-09-01. Electrical
20141132014-04-07. Electrical
14V1730002014-04-03. ELECTRICAL SYSTEM:ALTERNATOR/GENERATOR/REGULATOR
20091132009-04-16. Electrical
09V1260002009-04-16. ELECTRICAL SYSTEM
09V0660002009-02-23. ELECTRICAL SYSTEM:WIRING:INTERIOR/UNDER DASH
05V4120002005-09-19. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM

A recall listed here may apply to some of the same vehicles. Only the manufacturer can say whether it applies to one vehicle.

Other bulletins for the same vehicles and component
SA-041-26a2026-10-03. Service bulletin. DESCRIPTION If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices. Examples: 1. Devices connected to the DLC-2 (battery discharge/DTC stored) 2. Devices plugged into the 12V outlet 3. GPS tracking device (engine no start/battery discharge) 4. Dash cam (DTC stored) 5. Non-certified USB cable (Apple Carplay™/ Android Auto™ will not connect) 6. Over-sized wheels/tires (incorrect GPS location) 7. DTC C0023:14 8. Decorative trim and/or cover on the START/STOP ENGINE button
01-010-262026-09-02. Service bulletin. This bulletin supersedes the previously issued bulletin(s) listed below. The changes are noted in Red text. 01-012/22 10/06/22 DESCRIPTION Some vehicles may exhibit accumulation of dried coolant (1) around the water pipe (2). This is caused by a gap between the housing and pipe due to a press fitting during the manufacturing process. The accumulated coolant is solidified and plugs the gap in high temperature environment and the seepage is stopped and does not progress. This is normal and does not require a part replacement, clean off the dried coolant from around the pipe with a wire brush. REPAIR PROCEDURE 1. Verify the customer concern. 2. If the above condition is experienced, remove the accumulated coolant around the pipe (1) with a wire brush etc. NOTE: Perform the procedure on the vehicle. No need to remove the water pipe and hoses.
09-022-262026-08-04. Service bulletin. This bulletin supersedes the previously issued bulletin(s) listed below. The changes are noted in Red text. 09-042/04 12/10/04 DESCRIPTION Some vehicles may exhibit inoperative electric rear window defroster grid lines, integral antenna concerns causing radio reception issues or terminal tabs pulled from the rear window glass. Follow the diagnostic and repair procedures included in this service information to inspect and service rear defroster grid lines, integral antenna concerns or broken terminal tabs.
SA-041-262026-07-03. Service bulletin. This SA supersedes the previously issued SA(s) listed below. The changes are noted in Red. SA-061/25 12/17/25 DESCRIPTION If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices. Examples: 1. Devices connected to the DLC-2 (battery discharge/DTC stored) 2. Devices plugged into the 12V outlet 3. GPS tracking device (engine no start/battery discharge) 4. Dash cam (DTC stored) 5. Non-certified USB cable (Apple Carplay™/ Android Auto™ will not connect) 6. Over-sized wheels/tires (incorrect GPS location) 7. DTC C0023:14 8. Decorative trim and/or cover on the START/STOP ENGINE button Example 1: Some electrical devices connected to the DLC-2 connector by insurance or mobile phone companies may cause: Battery discharge. The device may disrupt the CAN system battery saver mode. • IDS/MMDS will not communicate with the vehicle due to poor DLC-2 connection. The aftermarket device may cause DLC-2 female terminals to spread open.
SA-029-262026-05-05. Service bulletin. This Service Alert supersedes the previously issued SA listed below: The changes are noted in Red. SA-011/24 02/12/24, 06/06/24, 07/29/24 DESCRIPTION Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers. SCHEDULED MAINTENANCE Refer to the applicable Workshop Manual or Owner's Manual for vehicle -specific manufacturer scheduled maintenance. Workshop Manual - Refer to section 00-00 SCHEDULED MAINTENANCE. Owner's Manual - Refer to section 8 Maintenance and Care. b. Note: Please refer to the information below outlining the services not included in Mazda's Factory Scheduled Maintenance: IMPORTANT: Recommending fluid flushes when not necessary can lead to customer confusion and dissatisfaction. Fluid flushing for preventive maintenance purposes is strongly discouraged, unless otherwise specified in a published procedure (Owner’s Manual, Workshop Manual, Technical Service Bulletin, etc.).
SA-026-262026-05-05. Service bulletin. This Service Alert supersedes the previously issued M-Tip(s) listed below. The changes are noted in Red text. MT-002/19 09/30/19 and 12/19/19 DESCRIPTION If an engine assembly is replaced after a catastrophic internal mechanical failure, clean the intake manifold internally before installing a replacement engine assembly. If the intake manifold is not cleaned properly, the replacement engine may fail prematurely. Metallic debris from the old engine (with catastrophic internal mechanical failure) may rest inside the intake manifold. When the new engine assembly is installed, debris in the intake manifold will be ingested into the new engine and cause internal damage. Clean the intake manifold internally to remove any debris from old engine before installing the new replacement engine assembly. If the intake manifold cannot be properly cleaned internally, replace it.
SA-021-262026-05-05. Service bulletin. This Service Alert supersedes the previously issued SAs and bulletin(s) listed below: The changes are noted below in red. SA-010/23 02/09/23 DESCRIPTION Some customers may experience one or more electrical malfunctions after a vehicle body repair. A newly painted fender stay (2) may be causing a poor front harness (1) ground connection. The front fender stay (2) newly painted surface at ground point (3), where attachment bolt (4) is seated, may create a poor front harness ground connection. NOTE: DO NOT paint ground point (3) attachment bolt (4) is seated. NEWLY INSTALLED FRONT FENDER STAY NOTE: CAUTION: If the bolt (4) contact area (3) is painted when the front fender stay (2) is newly replaced, it could cause a malfunction in the PCM. Before painting a newly replaced part, protect the bolt (4) contact area (3) with masking tape (5) as shown in the figure.
09-007-262026-02-03. Service bulletin. Some vehicles may exhibit the power window(s) not working properly (window does not move or has fallen into the door) and/or making an abnormal noise while operating the power window switch. This may be caused by the cable of the power window motor being damaged from water entry through area (1) of the front beltline molding. Convertible Top: To eliminate this concern, the shape of the door glass has been modified during mass production to prevent water entry to the power window regulator. Retractable Hardtop: No mass production change is scheduled.
09-005-262026-02-03. Service bulletin. If the right-side Blind Spot Monitoring (BSM) control module is replaced for any reason, it is also necessary to replace the left-side BSM control module in order to complete the radar aiming procedure. If the right-side BSM control module is replaced alone, "Automatic Configuration" and "BSM Radar Aiming" cannot be completed due to a programming error in the module. In most cases, if the left-side BSM control module is replaced alone, "Automatic Configuration" and "BSM Radar Aiming" can be completed without any problem (See CAUTION below for more details). Other possible symptoms that may be found if the right-side BSM module is replaced alone: BSM aiming fails “BSM OFF" indicator ON Center Display warning message BSM failsafe (No operation) DTC U3000:54 stored in memory DTC U1A4B:54 stored in memory (CX-3, MX-5 only) NOTE: Since a new BSM control module does not retain the vehicle specification information, it is necessary to acquire and store the vehicle specification information transmitted via CAN communication from the combination meter through automatic configuration after replacement.
SA-061-252026-01-04. Service bulletin. If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.