Service bulletin TSB 22-2023

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
Type	Service bulletin
NHTSA id	10209201
Published by NHTSA	2022-03-22
Manufacturer's number	TSB 22-2023
Manufacturer's date	2022-03-15
NHTSA component	EQUIPMENT; SERVICE BRAKES, HYDRAULIC; EQUIPMENT ADAPTIVE/MOBILITY

NHTSA's summary

Some 2021-2022 Mustang Mach-E vehicles built on or before 06-Jan-2022 may exhibit a vibration or pulsation from the brakes. This may be due to brake pad material bonded to the rotor. To correct the condition, follow the Service Procedure steps to replace the brake pads and resurface the rotors.

The document

The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.

Components

Brakes, Equipment and accessories

Vehicles listed
FORD MUSTANG MACH E	2021, 2022

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Recalls for the same vehicles and component
25V513000	2025-08-08. SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP:CONTROL UNIT/MODULE
24V777000	2024-10-18. SERVICE BRAKES, HYDRAULIC:ANTILOCK/TRACTION CONTROL/ELECTRONIC LIMITED SLIP:CONTROL UNIT/MODULE

A recall listed here may apply to some of the same vehicles. Only the manufacturer can say whether it applies to one vehicle.

Other bulletins for the same vehicles and component
SSM 54574	2026-02-17. Service bulletin. Some 2021-2022 Mustang Mach-E vehicles may exhibit a "Parking Brake Failure, Service Immediately message displayed in the instrument panel cluster (IPC) and diagnostic trouble codes (DTCs) C2007, C2008, C1034, U0293 and/or U0100 stored in the anti-lock brake system (ABS) module. To correct the condition, follow the technical instructions outlined FSA 22P31 (US) or 22B47 (Canada) for an appropriate repair direction.
TSB 25-2398	2025-09-03. Service bulletin. This article supersedes TSB 23-2021 to update the service procedure and labor times from M-time to AP-time and add a limit. Some of the vehicles listed in the Model statement above equipped with the rear view camera system only may exhibit the "Reverse Brake Assistance Not Available" message and diagnostic trouble code (DTC) B1578:78 stored in the image processing module A (IPMA) that cannot be cleared. This may be due to the IPMA software.
TSB 25-2397	2025-09-03. Service bulletin. This article supersedes TSB 22-2214 to update labor times from M-time to AP-time and add a limit. Some of the vehicles listed in the model statement above may exhibit at least one of the following conditions: - "Reverse Brake Assist Unavailable" message displayed in the instrument panel cluster (IPC) with missing active guide lines in the reverse camera display - Diagnostic trouble code (DTC) U0415:86 stored in the IPMA This may be due to a software issue with the anti-lock brake system (ABS) module.
SU-10.2.0 MachE	2025-07-02. Over-the-air update. "Quality improvements include: - Brake pedal tuning parameters updated for an improved pedal feel -Calibration update to ensure One Pedal Drive functionality"
TSB 24-2058	2024-04-03. Service bulletin. Some 2021-2023 Mustang Mach-E vehicles may exhibit a wind noise from the exterior mirror/A-pillar area when driving at or above 64 km/h (40 mph). This may be due to poor sealing of the lower mirror foam and the glass top run foam.. Some 2021-2023 Mustang Mach-E vehicles may exhibit a wind noise from the exterior mirror/A-pillar area when driving at or above 64 km/h (40 mph). This may be due to poor sealing of the lower mirror foam and the glass top run foam..
TSB 24-2034	2024-04-03. Service bulletin. 2021-2023 Mach-E vehicles may exhibit the drive mode default to normal mode while driving and <Drive Mode Not Available> message displays in the center display screen with or without Diagnostic Trouble Code (DTC) U0253 stored in the ABS module. This may be due to the software in the APIM.
SSM 52280	2024-03-05. Service bulletin. Some 2021-2024 Mustang Mach-E, 2022-2024 E-Transit/F-150 Lightning vehicles may have diagnostic trouble code (DTC) P1A3C stored in the off-board charger controller module (OBCC). The P1A3C is commonly set due to an interruption of the direct current (DC) fast charging process and should be disregarded. All other DTCs stored in the OBCC are to be addressed using applicable publications and/or normal diagnostics found in Workshop Manual, Section 414-03B.
TSB 24-2002	2024-02-06. Service bulletin. Some 2021-2023 Mustang Mach-E vehicles built on or before 04-Dec-2023 may exhibit a wind noise from the exterior mirrors/A-pillar area when driving at or above 40 mph (64 km/h). This may be due to poor sealing of the lower mirror foam and the glass top run foam.
TSB 23-2389	2024-01-05. Service bulletin. Some 2021-2022 Mach-E vehicles may experience an exterior charge status indicator not illuminating the blue charging segments after an over the air (OTA) update. This may be due to the software in the SYNC module (APIM). To correct the condition, follow the Service Procedure steps to reprogram the APIM. NOTE: The APIM software update that addresses the symptom listed in this bulletin may have been sent via Ford Power-Up software updates delivered over- the-air (OTA) to connected vehicles that have automatic updates enabled through the center display screen. Enter the vehicle identification number (VIN) in Professional Technician System (PTS) and check the OTA Dashboard under the Connected Vehicle tab for OTA update history. If an update to the APIM has successfully completed recently and the customer is reporting the symptoms are no longer present, this article may not apply.
TSB 23-2388	2024-01-05. Service bulletin. Some 2021-2023 Mach-E vehicles built on or before 29-May-2023 may experience an alarm activation even after the motion sensor function has been disabled through the pop-up menu at ignition off. This may be due to the software in the SYNC module (APIM). To correct the condition, follow the Service Procedure steps to reprogram the APIM. NOTE: The APIM software update that addresses the symptom listed in this bulletin may have been sent via Ford Power-Up software updates delivered over-the-air (OTA) to connected vehicles that have automatic updates enabled through the center display screen. Enter the vehicle identification number (VIN) in Professional Technician System (PTS) and check the OTA Dashboard under the Connected Vehicle tab for OTA update history. If an update to the APIM has successfully completed recently and the customer is reporting the symptoms are no longer present, this article may not apply.