Service bulletin NTB15097

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
Type	Service bulletin
NHTSA id	10192670
Published by NHTSA	2021-05-10
Manufacturer's number	NTB15097
Manufacturer's date	2015-11-05
NHTSA component	ENGINE AND ENGINE COOLING

NHTSA's summary

IF YOU CONFIRM: Coolant is leaking from the connector cap (bleeder cap). ACTION: 1. Remove the bleeder cap. 2. Install the new bleeder cap in reverse order of removal. See this bulletin for further details.

The document

The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.

Components

Engine

Vehicles listed
NISSAN NV	2014, 2015

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Other bulletins for the same vehicles and component
NTB17-082E	2022-03-12. Service bulletin. DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-097J	2022-03-12. Service bulletin. EVAP LEAK DTC P0442, P0455, P0456 INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13-027C	2022-03-12. Service bulletin. CAN COMMUNICATION – NETWORK DIAGNOSTIC FLOW CHART This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB10104B	2021-05-10. Service bulletin. IF YOU CONFRIM An oil leak at the right side block ball plug behind the alternator. ACTION Use a punch to seat the block ball plug in the hole (refer to the Service Procedure). NOTE - Do not replace the engine block for this incident if it should occur. See this bulletin for further detail.
NTB15055	2021-05-10. Service bulletin. SERVICE INFORMATION After ECM reprogramming, the Calibration Verification Number (CVN) needs to be automatically calculated prior to State emissions testing (also known as Inspection Maintainence, I/M, or SMOG testing depending upon location). Allowing the vehicle to idle for 22 minutes will allow for faster CVN calculation. It is recommended that customers utilize this method if the vehicle needs to be tested for emissions soon after ECM reprogramming. See this bulletin for further detail.
NTB14109	2021-05-10. Service bulletin. SERVICE INFORMATION Starting with 2010 Model Year, Nissan vehicles have been gradually incorporating a new type of DTC known as Permanent DTC or P-DTC. If a vehicle is equipped with P-DTCs, all emission related DTCs will also set a P-DTC if the MIL is turned ON. A listing of which DTCs that will also set a P-DTC is found in the DTC Index in the EC-Engine Control section of the Electronic Service Manual (ESM). If a DTC repair is performed and the DTC erased, a vehicle may fail an Emission Inspection and Maintenance test if the P-DTC is not also erased. See this bulletin for further detail.
NTB13102A	2021-05-10. Service bulletin. IF YOU CONFIRM * The MIL is on with a current or past DTC of P0448 (Evap Canister Vent Control Valve) set. ACTION Confirm that the Tube Assy-Filler is the updated part as shown in Figure 2. * If the Tube Assy-Filler is the old style as shown in Figure 1, replace it with the Tube Assy-Filler (Figure 2) from the Parts Information on the next page. * If the Tube Assy-Filler is the new style as show in Figure 2, replace only the "Vent Filter" also shown in Figure 2 with the procedure on page 2. Please see this bulletin for further details.
NTB12091A	2021-05-10. Service bulletin. SERVICE INFORMATION Replacement Engine Control Modules (ECMs) for many newer Nissan vehicles are now "Blank" ECMs. Blank ECMs come without software and must be programmed (not reprogrammed) before they will function. See this bulletin for further detail.
NTB20-057	2020-09-11. Service bulletin. VK56 CONNECTING ROD CAP BOLT SERVICE INFORMATION SERVICE INFORMATION A change has been made to the connecting rod cap bolt service part. The new service part (B in Figure 1) is visually different, but is a direct replacement for the original equipment part. IMPORTANT: See page 2 for the procedure to inspect the cap bolt service part for excessive stretch. If replacement of a single connecting rod cap bolt is indicated for any given connecting rod, both connecting rod cap bolts of the affected connecting rod must be replaced as a set.
NTB19-021	2019-04-15. Service bulletin. NISSAN; MIL ON WITH DTC P219A AND/OR P219B STORED This bulletin applies to Titan XD vehicles equipped with a VK56D gas engine only. SERVICE INFORMATION If the MIL is ON and DTC P219A (AIR FUEL RATIO IMBALANCE B1) and/or P219B (AIR FUEL RATIO IMBALANCE B2) is stored: - DO NOT replace the Air Fuel Ratio (A/F) sensor. - Refer to the applicable Electronic Service Manual (ESM) and follow the diagnostic procedure for DTC P219A and/or P219B.