Service bulletin PIC6421
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
| Type | Service bulletin |
|---|---|
| NHTSA id | 10184117 |
| Published by NHTSA | 2020-12-14 |
| Manufacturer's number | PIC6421 |
| Manufacturer's date | 2020-11-16 |
| NHTSA component | LATCHES/LOCKS/LINKAGES:HOOD:LATCH; ELECTRICAL SYSTEM:WIRING; STRUCTURE:BODY:HOOD |
NHTSA's summary
This Preliminary information communicates that a dealer may order a replacement hood latch and find that it comes with a three wire connector where the vehicle originally had a two wire connector on the hood latch. The technician is instructed on how to properly wire the new hood latch to the vehicle.
The document
The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.
Components
Body and frame, Electrical system, Latches and locks, Hood latch, Wiring and fuses
| CHEVROLET CAMARO | 2016, 2017, 2018 |
|---|
Listing a model year does not mean every vehicle of it is concerned: the document says which.
| PIC6163C | 2020-12-14. Service bulletin. This Preliminary Information communication provides information to the technician about vehicles that have several fasteners, located on either side of the hood latch, appear to be loose. Do not tighten, or otherwise move these two fasteners. These fasteners are part of the front fascia support bracket. They have a preset gap by design, and they have Loctite applied to the threads of the fastener so that this preset gap does not change. |
|---|---|
| 17NA292 | 2019-05-13. Service bulletin. This technical bulletin provides a procedure to inspect the wires and/or replace the Valve Rocker Arm Oil Control Valves if the DTCs listed are set. |
| 100089005G | 2019-05-13. Service bulletin. This warranty admin bulletin explains to the technician additional information may be needed when submitting transactions when doing wiring repairs. |
| 18NA270 | 2019-04-08. Service bulletin. This technical bulletin provides a procedure on locating an engine wiring harness chaffing concern at the rear side of the engine manifold and repair accordingly in circuit 2501. |
| 100089005H | 2019-03-18. Service bulletin. This warranty admin bulletin explains to the technician additional information may be needed when submitting transactions when doing wiring repairs. |
| 18258 | 2018-12-10. Service bulletin. 18258 - Service Update. These vehicles were built without anti-abrasion wrap on the engine wire harness designed to prevent potential wear-through of the wire harness insulation over extended periods of time. If insulation wear-through were to occur, damage to the harness wires may result. Damage to individual circuits may result in diagnostic trouble codes (DTC?s) being set. A service engine indicator may be displayed, and the engine may not start, run rough or run in reduced propulsion mode. Dealers will add an anti-abrasion wrap and sleeve to area of contact. |
| 18NA079 | 2018-05-21. Service bulletin. This technical bulletin provides a procedure to replace the drivers front door window regulator motor and door wiring harness if water and/or corrosion is found in the connectors. |
| 10-00-89-005E | 2018-05-21. Service bulletin. This warranty administration bulletin adds the 2016 model year to a communication which provides dealership personnel revised wiring repair labor operations and required additional information. |
| 16NA257 | 2018-05-07. Service bulletin. This technical bulletin provides a procedure to balance the folding top front latching mechanism and actuator motor to correct a condition of a "Top Not Secure" message being displayed on the DIC. |
| 17NA292 | 2018-04-23. Service bulletin. This technical bulletin provides a procedure to inspect the wires and/or replace the Valve Rocker Arm Oil Control Valves if the DTCs listed are set. |