Service bulletin NTB05-057c
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
| Type | Service bulletin |
|---|---|
| NHTSA id | 10180984 |
| Published by NHTSA | 2020-10-08 |
| Manufacturer's number | NTB05-057c |
| Manufacturer's date | 2020-09-30 |
| NHTSA component | EXTERIOR LIGHTING; EQUIPMENT |
NHTSA's summary
VOLUNTARY SERVICE CAMPAIGN 2002 – 2003 ALTIMA; HALOGEN HEADLAMP GROUND PLATE KIT Service Campaign ID # PB135 is no longer active. • Repair orders opened after this bulletin’s published date are no longer eligible for reimbursement under Campaign ID # PB135. • Please discard all previous versions of NTB05-057.
The document
The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.
Components
Equipment and accessories, Lighting
| NISSAN ALTIMA | 2002, 2003 |
|---|
Listing a model year does not mean every vehicle of it is concerned: the document says which.
| NTB09131B | 2021-05-10. Service bulletin. SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement "Certification Label" or "VIN Plate / Label" may be needed. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. See this bulletin for further detail. |
|---|---|
| P5216 | 2021-05-10. Service bulletin. To ensure customer satisfaction, Nissan extended the warranty for cracking of the rear sub-frame due to corrosion to a total of 13 years with unlimited mileage on all model year 2002-2005 Nissan Altima and 2004-2005 Nissan Maxima vehicles. |
| NTB15059 | 2021-05-10. Service bulletin. SERVICE INFORMATION The Service Procedure provided in this bulletin is for the installation of Repair Plates on vehicles that have rust in the floor pan area. See this bulletin for further detail. |
| NTB00042D | 2021-05-10. Service bulletin. SERVICE INFORMATION Changes or modifications to the front seat assembly trim materials may affect the proper operation of the Front Seat-Mounted Side-Impact Supplemental Air Bags and Passenger Occupant Classification Sensor and could result in serious personal injury or death. Nissan STRONGLY RECOMMENDS AGAINST making any change to seat trim materials from the factory equipped condition. This specifically applies to replacing the seat trim with non-factory materials; adding leather/cloth seat covers, seat pads, or seat storage pouches, etc. around or over the seat back and the passenger seat cushion. See this bulletin for further detail. |
| NTB08055C | 2021-05-10. Service bulletin. SERVICE INFORMATION Information necessary to service the Supplemental Restraint System (SRS) safely is included in the "RESTRAINTS" section of the Electronic Service Manual (ESM) for each vehicle. IMPORTANT: Turn the ignition switch OFF, disconnect both battery terminals, and wait at least 3 minutes before performing any service on the SRS. See this bulletin for further detail. |
| NTB92123D | 2021-05-10. Service bulletin. Nissan Original Equipment or Genuine Accessory Alloy wheels, along with their finish coating (clear, chrome, titanium, etc.), are specifically developed to achieve Nissan design and performance standards. These Original Equipment or Genuine Accessory wheels are subjected to testing to ensure they meet Nissan's standards. Nissan Original Equipment Alloy or Genuine Accessory wheels subjected to aftermarket chroming may no longer continue to meet these standards and may be seriously damaged. Therefore, Nissan most strongly discourages, and recommends that these wheels NEVER be subjected to, aftermarket chroming. See this bulletinfor further detail. |
| NTB-09-129 | 2010-04-07. Service bulletin. NISSAN: VENT CONTROL VALVE REPLACEMENT. WHEN REPLACING THE EVAP CANISTER VENT CONTROL VALVE FOR REASON: USE THE ONE LISTED ON PAGE 2; FOR VENT CONTROL VALVE REPLACEMENT PROCEDURE, REFER TO THE APPROPRIATE SECTION OF THE ELECTRONIC SERVICE MANUALS (ESM; WHEN INSTALLING THE NEW VALVE, DO NOT ADD ANY LUBE TO ITS O RING; FOR FRONTIER (D40 SERIES) ONLY, INSTALL THE PROTECTOR LISTED IN PARTS INFORMATION. *PE INCLUDES 2005-09 FRONTIER. UPDATED 12/8/10. *PE |
| NTB-03-074-C | 2010-03-03. Service bulletin. NISSAN: EXTERIOR LAMP FOGGING. OCCASIONALLY WATER IS NOTICED IN THE EXTERIOR LAMPS. THIS IS GENERALLY NOT DUE TO A DEFECT. ALL CURRENT EXTERIOR LAMP ASSEMBLIES ARE VENTED TO THE ATMOSPHERE (NOT SEALED). THIS IS NECESSARY TO ALLOW FOR EXPANSION AND CONTRACTION OF AIR FROM TEMPERATURE VARIATIONS (WARMER OR COLDER) WITHOUT DAMAGE TO THE LAMP. MOISTURE IN THE AIR SOMETIMES TRAVELS INTO AND OUT OF THE LAMP ASSEMBLY THROUGH THESE VENTS. CERTAIN ENVIRONMENTAL CONDITIONS MAY CAUSE MOISTURE TO CONDENSE. THE FOGGING/CLOUDINESS SHOULD DISAPPEAR OVER TIME WHEN THE LAMP IS IN A DRY ENVIRONMENT. NO MODELS LISTED. *PE UPDATED 5/7/10. *PE UPDATED 12/9/13. *PE |
| 03030 | 2007-05-10. Service bulletin. EXTERIOR LAMP FOGGING. *KB |
| 05057 | 2005-07-27. Service bulletin. CAMPAIGN ANNOUNCEMENT REGARDING SERVICE CAMPAIGN NTB05-057 - LOW BEAM HALOGEN HEADLAMP BULB ILLUMINATION FAILURE DUE TO POOR GROUND CONTACT. *TT CSC WAS RECEIVED. UPDATED 3/21/08. *NJ |