Service bulletin ITB20-018

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
Type	Service bulletin
NHTSA id	10178190
Published by NHTSA	2020-08-08
Manufacturer's number	ITB20-018
Manufacturer's date	2020-07-16
NHTSA component	STRUCTURE:BODY:DOOR; ELECTRICAL SYSTEM; EQUIPMENT

NHTSA's summary

POWER BACK DOOR WILL NOT OPERATE WITH REQUEST SWITCHES IF YOU CONFIRM On vehicles equipped with a Kick Motion Activated Liftgate, the back door (liftgate) will not open or close when requested to do so using the: • Intelligent Key • Back door request switch, located on the back door • Automatic back door switch, located on the instrument lower panel LH And DTC B2409 is either current or has been stored in the past. ACTION Replace the automatic back door control module. • Refer to the Electronic Service Manual (ESM) section: BODY EXTERIOR, DOORS, ROOF & VEHICLE SECURITY > DOOR & LOCK > WITH INTELLIGENT KEY SYSTEM > REMOVAL AND INSTALLATION > AUTOMATIC BACK DOOR CONTROL MODULE.

The document

The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.

Components

Body and frame, Electrical system, Equipment and accessories

Trouble codes named

B2409

Vehicles listed
INFINITI QX50	2019, 2020
INFINITI QX60	2018, 2019, 2020

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Recalls for the same vehicles and component
21V025000	2021-01-26. EQUIPMENT:OTHER:LABELS; TIRES

A recall listed here may apply to some of the same vehicles. Only the manufacturer can say whether it applies to one vehicle.

Other bulletins for the same vehicles and component
ITB22-025D	2026-08-28. Service bulletin. ROARING NOISE FROM THE ENGINE COOLING FAN ASSEMBLY AND THE A/C IS NOT COOLING IF YOU CONFIRM A roaring noise from the engine cooling fan assembly (engine fan on high not cycling) is present, and the Air Conditioning (A/C) is not cooling. ACTION 1. Check the hardware part number for the IPDM E/R. 2. Replace the IPDM E/R with the part number listed in the PARTS INFORMATION, if applicable. 3. Reconfigure the IPDM E/R, if applicable. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.
ITB09-063C	2026-04-29. Service bulletin. CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Infiniti by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). · The “Certification Label” (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).
ITB12-011R	2026-04-29. Service bulletin. TELEMATICS SERVICE INFORMATION See ITB19-029 for models built after those listed above for a different Service Procedure. SERVICE INFORMATION The Applied Vehicles are equipped with a wireless communication device called a Telematics Communication Unit (TCU). With an active Infiniti Connection® or Infiniti InTouch Services™, the TCU communicates with the Infiniti Data Center to provide various security and convenience services. This bulletin contains important service procedures that must be performed properly in order to set-up and maintain the telematics system for the Applied Vehicles. Ø A table has been provided on the next page that lists the model and year specific steps required to successfully configure a TCU after it has been replaced. Ø A check OFF sheet has been provided on page 21 to print and check off steps as they are performed. Please staple the completed Check OFF Sheet to the repair order.
ITB21-021A	2025-10-21. Service bulletin. IF YOU CONFIRM The client states that either the rear hatch is inoperative, or the rear hatch closes after opening only a small amount, AND DTC B2426-23 for “SPINDLE SENSOR LH” and/or DTC B2427-23 for “SPINDLE SENSOR RH” is stored, AND/OR There is a growling type noise from the rear hatch area when opening/closing the rear hatch. · DTC B2426-23 for “SPINDLE SENSOR LH” and/or DTC B2427-23 for “SPINDLE SENSOR RH” may also be stored. HINT: If any DTC other than B2426-23 and/or B2427-23 is stored, this bulletin does not apply. ACTION Replace ONLY the spindle unit that is confirmed to be setting one of the DTCs listed above and/or causing the growling noise. Do NOT replace both spindle units when diagnosis leads to replacement of only one. HINT: Rear hatch spindle units are not hydraulic systems. If a rear hatch spindle unit appears to be leaking, this is normal drainage of water (rain, car wash, condensation) and design intended water management. Do not replace spindle units for suspected leaking. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.
ITB23-023A	2025-02-25. Service bulletin. AEB WARNING LIGHT IS ON WITH WARNING MESSAGES DISPLAYED ON COMBINATION METER APPLIED VEHICLES: 2015-2024 Q50 (V37) 2015-2018 Q50 Hybrid (HV37) 2017-2022 Q60 (CV37) 2015-2019 Q70 (Y51) 2015-2018 Q70 Hybrid (HY51) 2019-2024 QX50 (J55) 2022-2024 QX55 (FJ55) 2015-2021 QX60 (L50) 2022-2024 QX60 (L51) 2015-2019 QX60 Hybrid (L50H) 2015-2024 QX80 (Z62) SERVICE INFORMATION The AEB system is designed to turn itself OFF during driving conditions (e.g., rain, snow, fog, etc.) that obstruct its sensors. This behavior is normal, and no repairs should be performed. When the AEB system performs an intentional shutdown, the customer may state the following: • The ICC stopped working while driving, • The AEB/FEB warning light is ON, or turned ON, while driving (Figure 1), • The message “Unavailable Front Radar Obstruction” or “Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner's Manual” has displayed while driving (Figure 2). AND • DTC C1A16, C1A16-97, C2582, or C2582-97 is the ONLY DTC stored. Figure 1 Figure 2 Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner’s Manual
ITB22-020B	2024-09-04. Service bulletin. TELEMATICS CONTROL UNIT RESET AFTER AUTOMATIC COLLISION NOTIFICATION SERVICE INFORMATION The Telematics Control Unit (TCU) has the ability to send an automatic collision notification when the vehicle is involved in an accident. Once an automatic collision notification is performed, the function becomes disabled and the TCU must be reset to re-enable the automatic collision notification function. Some models will store DTC B2E1B-97 for “Automatic eCAll locked” as “CURRENT” when this function is disabled. This bulletin describes how to reset the TCU after an automatic collision notification has been performed. For models with B2E1B-97 for “Automatic eCAll locked” set as “CURRENT”, complete the SERVICE PROCEDURE starting on page 2, and then erase DTCs after confirming the TCU condition is “UNLOCK”.
ITB22-017B	2024-09-04. Service bulletin. DTC B2E01-96 (INTERNAL BATTERY) STORED AS CURRENT IN IVC APPLIED SYSTEMS: Vehicles equipped with Telematics SERVICE INFORMATION CONSULT has been updated to allow DTC B2E01-96 for “Internal battery” to be cleared in the Telematics Control Unit (TCU). If DTC B2E01-96 is Current/Active in the TCU, and no additional Current/Active DTCs are present in the TCU, perform the SERVICE PROCEDURE starting on page 2. This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB19-042E	2024-09-04. Service bulletin. AV CONTROL UNIT REPLACEMENT PROCESS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. IF YOU CONFIRM The AV control unit needs to be replaced. ACTION 1. Read and save the VIN. 2. Read and save the configuration. 3. Replace the AV control unit. 4. Reprogram the AV control unit. 5. Configure the AV control unit. 6. Write the VIN to the AV control unit. IMPORTANT: Procedures 4-6 above must be performed in the order shown below. ORDER OF COMPLETION REPROGRAM AV Control Unit CONFIGURE AV Control Unit WRITE VIN to AV Control Unit Infiniti
ITB19-029E	2024-09-04. Service bulletin. TELEMATICS (IVC) SERVICE INFORMATION Vehicles equipped with factory telematics system HINT: • If the client experiences Wi-Fi hotspot related concerns only, DO NOT replace the TCU. Have the client contact the AT&T Support line at 1 (888) 719-7242. • See ITB12-011 for models built before those listed above. SERVICE INFORMATION The APPLIED VEHICLES are equipped with a wireless communication device called a Telematics Communication Unit (TCU). The TCU communicates with the Infiniti Data Center to provide various security and convenience services. This bulletin contains important service procedures that must be performed properly in order to set-up and maintain the telematics system for the APPLIED VEHICLES. • An Order of Completion table has been provided on the next page that lists the steps required to successfully configure a TCU after it has been replaced. • A CHECK-OFF SHEET has been provided on page 16. Print and check off steps as they are completed. Staple the completed CHECK-OFF SHEET to the repair order.
ITB21-025B	2024-07-19. Service bulletin. DTC C1A17-49 STORED IN LASER/RADAR This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.