Service bulletin 18-103-19

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
Type	Service bulletin
NHTSA id	10170404
Published by NHTSA	2020-01-21
Manufacturer's number	18-103-19
Manufacturer's date	2019-12-19
NHTSA component	POWER TRAIN

NHTSA's summary

Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the Engine Control Module (ECM), also known as a PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs have been set: P013A-00 - O2 Sensor Slow Response Rich To Lean Bank 1 Sensor 2. P015A-00 - O2 Sensor Delayed Response Rich To Lean Bank 1 Sensor 1. P1CEA-00 - Boost Side EVAP Purge System Performance. P0096-00 - Intake Air Temperature Sensor 2 Circuit Range-Performance. P04DB-00 - Crankcase Ventilation System Disconnected. P024A-00 - Charge Air Cooler Bypass Control "A" Range/Performance. P2097-00 - Post Catalyst Fuel Trim System Rich. P2B2F-00 - Fan 1 Performance/Stuck Off. P24D6-00 - EVAP System Pressure Sensor/Switch "B" Circuit Range/Performance. P01BA-00 - Engine Oil Temperature Sensor "B" Range/Performance. P026E-00 - Charge Air Cooler Coolant Pump Performance. P164E-00 - A/C Clutch Relay Control Range/Performance. P0191-00 - Fuel Rail Pressure Sensor "A" Circuit Range/Performance. P2299-00 - Brake Pedal Position/Accelerator Pedal Position Incompatible. U1008-00 - LIN 1 BUS. Customers may experience one or more of the following:Not passing vehicle certification during state inspections if performed after a system reset. Driveability issues. Engine misfire when cold. In addition, the following improvements are also available:Turbo coolant pump after run duration and on-off strategy update, to improve turbo O-ring durability. Message ?S&S Not Available? will be changed to ?Hood Open?. Improved idle stability during tip in tip out. Improved idle stability during an Engine Start Stop (ESS) event.

The document

The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.

Components

Transmission and driveline

Trouble codes named

P0096, P013A, P015A, P0191, P01BA, P024A, P026E, P04DB, P164E, P1CEA, P2097, P2299, P24D6, P2B2F, U1008

Vehicles listed
ALFA ROMEO STELVIO	2019

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Recalls for the same vehicles and component
2019110	2019-03-01. Powertrain

A recall listed here may apply to some of the same vehicles. Only the manufacturer can say whether it applies to one vehicle.

Other bulletins for the same vehicles and component
S2621000003 REV.A	2026-03-18. Service bulletin. The vehicle will exhibit a service transmission/check engine warning indicator for the following transmission models: 845RE, 8HP45, 850RE, 8HP50, 8HP70, 8HP75, 8HP75-PHEV, 8HP75-LCV, 8HP90, 8HP95. Transmissions may exhibit the following diagnostic codes: P07E4, P1DB2, P0716, P1B14, P0733, P1D90, P1DB7, P1B13.
1804523	2023-05-30. Service bulletin. Flash: Powertrain Control Module (PCM) Updates Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs have been set: ? P0331-00 - Knock Sensor 2 Circuit Range/Performance. ? P0106-00 - Manifold Absolute Pressure/Barometric Pressure Circuit Range/Performance. ? P013A-00 - O2 Sensor Slow Response Rich To Lean Bank 1 Sensor 2. ? P015A-00 - O2 Sensor Delayed Response Rich To Lean Bank 1 Sensor 1. ? P026E-00 - Charge Air Cooler Coolant Pump Performance. ? U1008-00 - LIN 1 BUS. ? P1CEA-00 - Boost Side EVAP Purge System Performance. Customers may experience one or more of the following: ? Not passing vehicle certification during state inspections if performed after a system reset. ? Drive-ability issues. In addition, the following improvement is also available: ? Turbo coolant pump after run duration and on-off strategy update, to improve turbo O-ring durability. This bulletin involves reprogramming the PCM with the latest available software.
S2308000004	2023-02-13. Service bulletin. Vehicle Cranks, No Start
S1908000102	2022-10-17. Service bulletin. (Rev. A) Power Inverter Load Ratings
9004335	2022-10-17. Service bulletin. Turbocharger If the turbo is being replaced for an oil leak concern, please inspect the area around the turbo oil feed o-ring for a leak. The o-ring is serviced separately and complete turbo replacement may not be necessary.
S2018000008	2022-10-17. Service bulletin. Engine Surge Feel and/or Diagnostic Trouble Code P0299 ? Turbo Underboost Condition After Updating The Powertrain Control Module (PCM) Software. (ETL, ETM, ETN Engines)
S2208000073	2022-10-17. Service bulletin. No Start, After Flash And Or PCM Replace, DTC P0513 Invalid Skim Key Setting
S2223000047	2022-09-26. Service bulletin. ACC Does Not Operate. Start Stop Unavailable, ACC Unavailable Service Required Messages. C1452-86 Engine Torque DASM- Signal Invalid
S1821000001	2022-09-26. Service bulletin. Gear Ratio DTC?s, Transmission Shift Concerns, Does Not Shift At Times, Shudders
9004009	2022-09-26. Service bulletin. Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.