Service bulletin 18-010-14 REV. A

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
Type	Service bulletin
NHTSA id	10139836
Published by NHTSA	2018-06-11
Manufacturer's number	18-010-14 REV. A
Manufacturer's date	2014-11-14
NHTSA component	FUEL SYSTEM, DIESEL

NHTSA's summary

Flash: Doser Control Unit (DCU), Heater Thaw Time Improvements And MIL Illumination This bulletin involves selectively erasing and reprogramming the Doser Control Unit (DCU) with new software. Software improvements are available for the Diesel Exhaust Fluid (DEF) DCU on vehicles equipped with a Cummins 6.7L turbo Diesel. The software contains improvements for the following: Increase in DEF thaw time when ambient and DEF tank temperatures are below -14°C. (7°F.). P208D - (DIESEL EXHAUST FLUID) REDUCTANT PUMP CONTROL CIRCUIT HIGH P202E - (DIESEL EXHAUST FLUID) REDUCTANT INJECTOR PERFORMANCE

The document

The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.

Components

Fuel system

Trouble codes named

P202E, P208D

Vehicles listed
RAM 2500	2013, 2014
RAM 3500	2013, 2014
RAM 4500	2013, 2014
RAM 5500	2013, 2014

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Recalls for the same vehicles and component
2014449	2014-10-09. Fuel System
14V635000	2014-10-08. ENGINE AND ENGINE COOLING:ENGINE:DIESEL; FUEL SYSTEM, DIESEL

A recall listed here may apply to some of the same vehicles. Only the manufacturer can say whether it applies to one vehicle.

Other bulletins for the same vehicles and component
1400114	2023-01-17. Service bulletin. Fuel Gelling in Cold Ambient Temperatures This bulletin involves reconfiguring the Body Control Module (BCM). Some customers may experience a Malfunction Indicator Lamp (MIL) due to fuel related Diagnostic Trouble Code (DTC) and/or may have a hard or no start condition due to fuel gelling in cold ambient temperatures (20°F or -7°C) or below. DTCs, such as P0087, P0191 or P026B (or other DTCs) may have been set.frame mounted fuel filter heater not to function. The condition is due to a configuration setting in the Body Control Module (BCM).
2500115	2023-01-09. Service bulletin. Diesel Exhaust Fluid (DEF) Level Gauge Inaccurate Or Stuck This bulletin involves verifying the correct DEF level in the tank and if necessary, replacing the DEF pump module. A small number of customers may comment that their DEF level gauge is stuck for long periods of time or is erratic. The customer may also experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find one or more of the following Diagnostic Trouble Codes (DTCs). ? P203B - Reductant Level Sensor Circuit Performance ? P203C - (Diesel Exhaust Fluid) Reductant Level Sensor Circuit Low. ? P203D - (Diesel Exhaust Fluid) Reductant Level Sensor Circuit High.
1805416	2022-12-19. Service bulletin. Flash: 6.7L Diagnostic And System Improvements This bulletin involves reprogramming the Engine Control Module/Powertrain Control Module (ECM/PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) Illumination. Upon further investigation, a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: · P218F - Reductant No Flow Detected. · P242F - Diesel Particulate Filter Restriction - Ash Accumulation. · P2281 - Air Leak Between MAF And Throttle Body. · P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in). · U110E - Lost Ambient Temperature Message. · P20E8 - (Diesel Exhaust Fluid) Reductant Pressure Too Low. · P1477 - Intake Air Diverter Valve Position Sensor Circuit Shorted To Ground. · U3017 - Control Module Timer/Clock Performance. · P0087 - Fuel Rail Pressure Too Low. · P0544 - Exhaust Gas Temperature Sensor Circuit - Sensor 1/1. · P0128 - Thermostat Rationality. In cold ambient temperatures. · P214D - SCR NOx Catalyst Outlet Temperature Too High During Particulate Filter Regeneration. · P24A5 - Exhaust Gas Recirculation (EGR) Cooler Bypass Bank 1 Control Stuck. · P040B - Exhaust Gas Recirculation Temperature Sensor ?A? Circuit Performance. · U1421 - Implausible Ignition Key Off Time Received. · P0420 - Catalyst Efficiency Below Threshold. · P026B - Injection Timing Performance. · P04DB - Crankcase Ventilation System Disconnected. · P1C55 - NOx Sensor Intermittent - Bank 1 Sensor 1. · P202E - Diesel Exhaust Fluid (DEF) Reductant Injector Performance. · P20EE - SCR NOx Catalyst Efficiency Below Threshold - Bank 1. · P2002 - Diesel Particulate Filter Efficiency Below Threshold. · P0604 - Internal Control Module RAM. · P1451 - Diesel Particulate Filter System Performance.
2500116	2022-11-21. Service bulletin. Diagnosing A Urea Module That Is Exposed To Diesel Fuel This bulletin involves discussing what will happen to the rubber material used in the urea pump when exposed to diesel fuel. This unit is sometimes referred to as the Selective Catalyst Reductant (SCR) module or the Adblue Delivery Module (ADM). Units exposed to hydrocarbons have a particular failure mode, the rubber heater unit is crinkled and in some cases the metal heater protrudes through the rubber membrane. The rubber material used in this unit is designed to withstand Diesel Exhaust Fluid (DEF) only. Exposure to fluids that contain hydrocarbons (i.e. diesel fuel) will damage the unit beyond repair. Units returned that exhibit this failure mode will have warranty claims that are rejected. Units that exhibit this failure mode should be considered customer abuse and should not be covered under warranty. Use the Hydroscopic test paper (P/N 223-44-863) available through MoparEssentialTools.com to confirm exposure.
S2214000003	2022-11-07. Service bulletin. Guidelines For The Use Of Alternative Diesel Fuels.
18-038-16	2022-10-24. Service bulletin. P20EE SCR NOX Catalyst Efficiency Below Threshold Bank 1 This bulletin involves verifying the proper operation of the Diesel Exhaust Fluid (DEF) system and, if necessary, replacing the Selective Catalyst Reduction (SCR) Catalyst assembly. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find Diagnostic Trouble Code (DTC) P20EE SCR NOX Catalyst Efficiency Below Threshold Bank 1 set in the Powertrain Control Module (PCM) memory.
18-091-16	2022-09-26. Service bulletin. Flash: Powertrain Diagnostic And System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that the following Diagnostic Trouble Codes (DTCs) have been set. Several software improvements are available for the following conditions. The Following DTC has been changed from a two trip fault to a one trip fault: · U1A24 - Lost Communication With Ammonia Sensor. Prevent or reduce MIL illumination when no defect is present for the following DTCs. These faults have been changed from a one trip fault to a two trip fault: · P0201 - P0206 - Fuel Injector X Circuit/Open. · P049D - EGR Control Position Exceeding Learning Limit. · P0711 - Transmission Temperature Sensor Performance. · P0712 - Transmission Temperature Sensor Low. · P0713 - Transmission Temperature Sensor High. · P0714 - Transmission Temperature Sensor Intermittent. · P0740 - TCC Out Of Range. · P0869 - Line Pressure High. · P0933 - Hydraulic Pressure Sensor Range/Performance. · P0934 - Line Pressure Sensor Circuit Low. · P0935 - Line Pressure Sensor Circuit High. · P1775 - Solenoid Switch Valve Latched In TCC Position. · P1776 - Solenoid Switch Valve Latched In LR Position. · U0100 - Lost Communication With ECM/PCM. · U0002 - CAN C Bus Off performance - Bus Off. · P2281 - Air Leak Between MAF And Throttle Body. · P218F - Reductant No Flow Detected. · P242F - Diesel Particulate Filter Restriction - Ash Accumulation. · P20E8 - (Diesel Exhaust Fluid) Reductant Pressure Too Low. · P202E - Diesel Exhaust Fluid) Reductant Injector Performance. · P209F - Diesel Exhaust Fluid) Reductant Tank Heater Control Circuit Performance. · P218F - Reductant No Flow Detected. · P205E - (Diesel Exhaust Fluid) Reductant Tank Temperatur
1803014REVB	2022-09-26. Service bulletin. Flash: 6.7L Diagnostic and System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. Several software improvements are available for vehicles equipped with a Cummins 6.7L turbo Diesel.Prevent Or Reduce Malfunction Indicator Lamp (MIL) Illumination When No Defect is Present For The Following Diagnostic Trouble Codes (DTCs). These Faults Have Been Changed From P0201 - P0206 - Fuel Injector X Circuit/Open. P049D - EGR Control Position Exceeding Learning Limit. P0711 - Transmission Temperature Sensor Performance. P0712 - Transmission Temperature Sensor Low. P0713 - Transmission Temperature Sensor High. P0714 - Transmission Temperature Sensor Intermittent. P0740 - TCC Out Of Range. P0869 - Line Pressure High. P0933 - Hydraulic Pressure Sensor Range/Performance. P0934 - Line Pressure Sensor Circuit Low. P0935 - Line Pressure Sensor Circuit High. P1775 - Solenoid Switch Valve Latched In TCC Position. P1776 - Solenoid Switch Valve Latched In LR Position. U0100 - Lost Communication With ECM/PCM. U0002 - CAN C Bus Off performance - Bus Off. U110E - Lost Ambient Temperature Message.The Following DTC Has Been Changed From A Two Trip Fault To One Trip Fault: U1A24 - Lost Communication With Ammonia Sensor.Improvements To Prevent Or Reduce Malfunction Indicator Lamp (MIL) Illumination When No Defect Is Present For: U3017 - Control Module Timer/Clock Performance. P026B - Injection Timing Performance. P0128 - Thermostat Rationality. In cold ambient temperatures. P0087 - Fuel Rail Pressure Too Low. P2281 - Air Leak Between MAF and Throttle Body. U1421 - Implausible Ignition Key Off Time Received. P026A - Charge Air Cooler Efficiency Below Threshold. P04DB - Crankcase Ventilation System Disconnected. P0544 - Exhaust Gas Temperature Sensor Circuit - Bank 1 Sensor 1. P0562 - Battery Voltage Low. P0604 - Internal Control Module RAM Error. P1451 - Diesel Particulate Filter
1805314REVB	2022-09-26. Service bulletin. Flash: 6.7L Diagnostic And System Improvements Bulletin involves reprogramming the Powertrain Control Module (PCM) with new software. Several software improvements are available for vehicles equipped with a Cummins 6.7L turbo diesel. They are as follows:Prevent Or Reduce Malfunction Indicator Lamp (MIL) Illumination When No Defect is Present Following Diagnostic Trouble Codes (DTCs). These Faults Have Been Changed From P0201 - P0206 - Fuel Injector X Circuit Open Fault Codes. U110E - Lost Ambient Temperature Message. P049D - EGR Control Position Exceeding Learning Limit. P226C - Turgocharger Boost Control ?A? Slow Response.The Following DTC Has Been Changed From A Two Trip Fault To One Trip Fault: U1A24 - Lost Communication With Ammonia Sensor.Improvements To Prevent/ Reduce Malfunction Indicator Lamp (MIL) Illumination When No Defect Is Present For: U3017 - Control Module Timer/Clock Performance. P0087 - Fuel Rail Pressure Too Low. P2281 - Air Leak Between MAF And Throttle Body. P0544 - Exhaust Gas Temperature Sensor Circuit - Sensor 1/1. P0128 - Thermostat Rationality. In cold ambient temperatures. P214D - SCR NOx Catalyst Outlet Temperature Too High During Particulate Filter Regeneration. P24A5 - EGR Cooler Bypass Bank 1 Control Stuck. P040B - Exhaust Gas Recirculation Temperature Sensor ?A? Circuit Performance. U1421 - Implausible Ignition Key Off Time Received. P0420 - Catalyst Efficiency Below Threshold. P026B - Injection Timing Performance. P04DB - Crankcase Ventilation System Disconnected. P1C55 - NOx Sensor Intermittent - Bank 1 Sensor 1. P202E - Diesel Exhaust Fluid (DEF) Reductant Injector Performance. P20EE - SCR NOx Catalyst Efficiency Below Threshold - Bank 1. P2002 - Diesel Particulate Filter Efficiency Below Threshold. P0604 - Internal Control Module RAM. P1451 - Diesel Particulate Filter System Performance.Other Updates Included: Urea system calibration changes. Fuel Filter Minder Calibrat
1800214REVC	2022-09-26. Service bulletin. Flash: 6.7L Diagnostic And System Improvements This bulletin involves selectively erasing and reprogramming the Engine Control Module (ECM/PCM) with new software. Several software improvements are available for vehicles equipped with a Cummins 6.7L turbo Diesel.Prevent Or Reduce Malfunction Indicator Lamp (MIL) Illumination When No Defect is Present For The Following Diagnostic Trouble Codes (DTCs). These Faults Have Been Changed From A One Trip Fault To A Two Trip Fault: P0201 - P0206 - Fuel Injector X Circuit/Open Fault Codes. U110E - Lost Ambient Temperature Message. P049D - EGR Control Position Exceeding Learning Limit.Improvements To Prevent Or Reduce Malfunction Indicator Lamp (MIL) Illumination When No Defect Is Present For: U3017 - Control Module Timer/Clock Performance. P0087 - Fuel Rail Pressure Too Low. P0544 - Exhaust Gas Temperature Sensor Circuit - Sensor 1/1. P2281 - Air Leak Between MAF And Throttle Body. P0128 - Thermostat Rationality. In low ambient temperatures. U1421 - Implausible Ignition Key Off Time Received. P202E - Diesel Exhaust Fluid (DEF) Reductant Injector Performance. P20EE - SCR NOX Catalyst Efficiency Below Threshold - Bank 1. P2002 - Diesel Particulate Filter Efficiency Below Threshold. P0604 - Internal control Module RAM Error. This DTC may be caused by enabling the remote throttle feature via the EVIC, and it will be accompanied by a ?service electronic throttle control? message in the EVIC.Other Updates: Urea system calibration changes. Fuel Filter Minder Calibration Changes. Cruise control system improvements. Improvements in exhaust brake switch operation. Charging system improvements for dual alternator applications. Various wiTECH data and system test additions and improvements. OBD Template changes for P2453. Dual Fuel Tank component update. Inducement Timer Reset (Feature enable in wiTech). PTO Denied Status Message Update. PTO Horn Request sent to Body Control Unit (BCU.)