Service bulletin LI35.00-N-060958
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
| Type | Service bulletin |
|---|---|
| NHTSA id | 10135864 |
| Published by NHTSA | 2018-05-07 |
| Manufacturer's number | LI35.00-N-060958 |
| Manufacturer's date | 2015-06-09 |
| NHTSA component | POWER TRAIN |
NHTSA's summary
Humming, droning from the drivetrain on vehicles with all-wheel drive (4x4)
The document
The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.
Components
Transmission and driveline
| MERCEDES-BENZ SPRINTER 906 | (the catalog's model; the bulletin names a series or trim of it) |
|---|---|
| MERCEDES-BENZ SPRINTER 906 | 2010, 2011 (the catalog's model; the bulletin names a series or trim of it) |
Listing a model year does not mean every vehicle of it is concerned: the document says which.
| LI28_00-N-079097_1_en | 2026-09-04. Service bulletin. Complaint While driving through muddy / sandy/ off road terrain "4Matic Currently Unavailable" message on the dash Cause This vehicle is not equipped with a fixed force distribution AWD, rather force is only applied to the front axle according to ESP calculations. As per GF28.00‑D‑ 9900A: "vehicles with 4MATIC all‑wheel system and variable force distribution, an electronically regulated multiplate clutch integrated into the transfer case provides for the torque distribution. If the multiplate clutch is open during normal driving operation, only the rear axle drives the vehicle. If the clutch is closed, the front axle comes into play." The message "All‑wheel drive temporarily unavailable" is not indicative of a malfunction but rather informs the driver that all‑wheel drive is currently not available due to the transfer case clutch overheating. This occurs when the vehicle is driven in such a way that maximum front axle torque is needed for an extended period, causing the clutch to get excessively hot. If the vehicle is being driven under heavy load conditions, like in deep sand or snow, the rear axle may slip while the front axle does not deliver power. The transfer case then attempts to distribute torque to correct the slip, but it is limited to a maximum of 1150 Nm to protect the front axle transmission. In extended heavy‑load scenarios, the multidisk clutch in the transfer case slips, increasing the temperature. If the temperature model detects a critical temperature of 240°C, the system protects itself by disconnecting until it cools down to around 160°C, after which the all‑wheel drive becomes available again and the warning message disappears.Vehicles can handle flat terrain easily, but steep slopes or situations where wheels slip might cause additional resistance, leading to the described protection events and message in the dash. Remedy Recommendation is to release the vehicle back to the client with an explanation that the vehicle is operating as designed. Please advise the client to limit vehicle acceleration in limited traction situations to avoid disabling of the 4Matic system ‑ please see "Notes on all‑wheel drive" provided in the operators manual. |
|---|---|
| LI14.20-N-073867 | 2026-07-02. Service bulletin. Complaint Complaint A: The engine is jolting/bucking between 1700 and 1900 rpm. Complaint B: One or more mechanical related fault codes for EGR Valve stored in CDI control unit, with possible Check Engine Light. Review list of mechanical fault codes in table below. NOTE: If one or more electrical related fault codes for EGR Valve are also present in CDI, utilize Complaint C. Review list of electrical fault codes PDF document in attachments. Complaint C: One or more electrical related fault codes for EGR Valve stored in CDI control unit, with possible Check Engine Light. Review list of electrical fault codes PDF document attached. NOTE: This LI supersedes LI14.20-N-073813, which is no longer valid. Cause Cause of Complaint A: Increased friction between the EGR Valve blade and seat due to soot deposits causing a delay of the EGR Valve being able to reach the target value of the EGR Valve position controller. NOTE: This causes the EGR Valve blade and potentially the boost pressure controller to oscillate. Cause of Complaint B: Soot deposits between the EGR Valve blade and seat leading to the EGR Valve no longer being able to meet the de-sired target of the EGR Valve position controller. Cause of Complaint C: Internal EGR Valve or other electrical faults related to the EGR Valve function. Remedy Remedy for Complaint A: Perform the following steps: 1. Disable the EGR Valve (Y27/17) by disconnecting the electrical connector. 2. Perform a test drive to check if the jolting/bucking issue resolves. 3. If the jolting/bucking is resolved, proceed to Remedy for Complaint B. 4. If jolting/bucking is still present, proceed with diagnosis to determine the root cause. Consider checking the follo-wing, but not limited to: •EGR system including the EGR Cooler, EGR Bypass Flap, EGR Temperature Sensor, and pipes for proper operati-on, excessive sooting and/or clogging, as well as EGR Bypass Flap vacuum element, switchover valve, and vacuum system. •Visually check the leak oil line or T-piece; reference LI07.00-N-059118. |
| LI28.00-N-063339 | 2026-01-02. Service bulletin. Clunking noise on load change or gear engagement Complaint Clunking noise can be heard on some load changes or when changing from N->R or N->D Cause Movement of transfer case splines Remedy Apply bearing retainer (green) Loctite to both output shaft splines of the transfer case. Loctite 648, 609 and 603 are acceptable for this repair. Note: Do not apply Loctite to input shaft (connection with transmission) splines of the transfer case else possible damage could occur. |
| LI27.19-N-079793 | 2025-10-07. Service bulletin. Complaint Transmission control unit Y3/8n4 (fully integrated transmission control unit (VGS)) not listed in quick test and/or no communication possible with VGS. Cause Transmission control unit Y3/8n4 Remedy For vehicles with 722.9 transmission: Ensure LI54.15-P-057373 is performed before replacing any component parts. After processing and complying with the above document(s): 1. Perform an ignition reset on Y3/8n4 (VGS) 2. Inspect transmission connector for loose connections, damaged wiring or pins and any other concerns. If communication with the VGS cannot be established, the complete valve body ('electrohydraulic controller unit (EHS)') must be replaced. Installation of a VGS repair kit is not permitted in this case as it is not possible to transfer the necessary valve characteristics without communication with the original control unit. |
| LI2700N048696 | 2021-12-20. Service bulletin. Automatic transmission oil loss in area of electrical connection and oil pan gasket. |
| LI0708N0652191 | 2021-12-20. Service bulletin. Reduced engine power output. |
| LI0704N0605273 | 2021-12-20. Service bulletin. Reduced engine power output. |
| LI27 00-N-066833 | 2019-04-08. Service bulletin. Transmission leak in area of oil pump |
| LI49 00-N-067929 | 2018-12-17. Service bulletin. Automatic Transmission Housing Cracked: Damage Resulting From Cracked Diesel Particulate Filter Bracket |
| LI42.10-N-048721 | 2018-05-07. Service bulletin. Brake noises (squeaking) at the front axle |