WenmarOpen by Wenmar Pro

Service bulletin 5NP-D2Y6N-12

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
TypeService bulletin
NHTSA id10089623
Published by NHTSA2017-01-26
Manufacturer's number5NP-D2Y6N-12
Manufacturer's date2016-11-04
NHTSA componentPOWER TRAIN:AUTOMATIC TRANSMISSION

NHTSA's summary

"UPDATE THE WARRANTY INFORMATION. DESCRIPTION: DO NOT REPLACE THE TRANSMISSION FOR THE DTC LISTED BELOW. INSTEAD, FOLLOW THE REPAIR PROCEDURE AND REPLACE THE E-MODULE."

The document

No address for NHTSA's copy can be built for this communication. Ask the dealer for it by the manufacturer's number.

Components

Transmission and driveline, Automatic transmission

Vehicles listed
GENESIS G802017
GENESIS G902017
HYUNDAI EQUUS2012, 2013, 2014, 2015, 2016
HYUNDAI EQUUS2017
HYUNDAI GENESIS2012, 2013
HYUNDAI GENESIS2015, 2016
HYUNDAI GENESIS COUPE2013, 2014, 2015, 2016

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Recalls for the same vehicles and component
15V0970002015-02-19. EXTERIOR LIGHTING:TAIL LIGHTS; ELECTRICAL SYSTEM; POWER TRAIN:AUTOMATIC TRANSMISSION:GEAR POSITION INDICATION (PRNDL)

A recall listed here may apply to some of the same vehicles. Only the manufacturer can say whether it applies to one vehicle.

Other bulletins for the same vehicles and component
21-AT-010HG2024-04-11. Service bulletin. This TSB provides a procedure to replace the solenoids listed below for slipping, shift flare and/or harsh shift during the 2~3, 3~4 or 4~5 upshift.
19-AT-023HG2024-04-11. Service bulletin. If you are servicing a vehicle with a transmission slipping concern, follow the Service Procedure shown below and perform a stall test. This TSB provides a procedure to test each clutch in the transmission. If the vehicle fails the stall test, replace the transmission. PASS: Stall speed is between 1700~2900 rpm (See shop manual for stall speed). FAIL: Engine revs to redline limit (6,000~6,500 rpm). If so, replace the transmission.
19-AT-011HG2019-07-01. Service bulletin. The procedure describes the procedure to check the ATF level for 8-speed Rear-Wheel-Drive vehicles.
19-AT-011H2019-07-01. Service bulletin. The procedure describes the procedure to check the ATF level for 8-speed Rear-Wheel-Drive vehicles.
19-AT-008H2019-05-20. Service bulletin. When servicing a vehicle with a ?Check Engine light? and any of the DTCs listed below, follow the Service Procedure and replace the related solenoid and E-module.
19-FL-003HG2019-05-20. Service bulletin. This bulletin provides the procedure to write the Vehicle Identification Number (VIN) during the replacement of the Engine Control Module (ECM) or Powertrain Control Module (PCM). Once the VIN has been programmed to the ECM/PCM, it cannot be removed or overwritten.
19-AT-007H2019-05-20. Service bulletin. This bulletin provides a procedure to transfer oil pressure data to the TCU using GDS Mobile. This procedure is necessary to reduce the TCU learning time and improve the shift quality.
19-AT-007HG2019-05-20. Service bulletin. This bulletin provides a procedure to transfer oil pressure data to the TCU using GDS Mobile. This procedure is necessary to reduce the TCM learning time and improve the shift quality.
19-AT-001HG2019-03-18. Service bulletin. When servicing a vehicle with a ?Check Engine light? and any of the DTCs listed below, follow the Service Procedure and replace the E-module.
5NP-H3D9Z-032017-08-10. Service bulletin. The following vehicles are equipped with an 8-speed automatic transmission. The ATF level can be checked by the procedure shown below.