WenmarOpen by Wenmar Pro

Service bulletin 14B10

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
TypeService bulletin
NHTSA id10058264
Published by NHTSA2015-08-24
Manufacturer's number14B10
Manufacturer's date2015-05-15
NHTSA componentENGINE

NHTSA's summary

FORD 2014 F-150 W/3.7L: THIS TSB CONTAINS AN OWNER NOTIFICATION LETTER. SELECT DOCUMENT SEARCH BUTTON BELOW. CUSTOMER SATISFACTION PROGRAM EFFECTIVE NOV.13,2015 FOR VEHICLE MODELS REGARDING THE ENGINE BLOCK REPLACEMENT. *LJ

The document

No address for NHTSA's copy can be built for this communication. Ask the dealer for it by the manufacturer's number.

Components

Engine

Vehicles listed
FORD F-1502014

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Other bulletins for the same vehicles and component
SSM 523342024-03-20. Service bulletin. Some 2011-2024 Mustang and F-150 vehicles equipped with a 5.0L engine may exhibit a tick tap and/or typewriter ticking noise at idle after an engine oil change. It is often referred to as typewriter noise because of its similarity to the sound of a mechanical typewriter. The noise in question may be heard on some engines when engine temperatures reach 150°F (65°C) or higher and engine speed is at idle up to approximately 1700 RPM. It can typically be heard at the front wheel well and is often isolated to the transmission bell housing or oil pan area. The typewriter noise tick rate can be faster or slower and is not detrimental to the engine function or durability and has no short or long term effects on the engine. This an operating characteristic of the 5.0L engine and no repairs should be attempted. This information along with an example audio clip has been added to the WSM Section 303-00 Engine System General Information > Diagnosis and Testing > Engine > PPT F > Step F2.
SSM 497612021-05-03. Service bulletin. Some 2011-2021 Mustang and F-150 vehicles equipped with a 5.0L engine may exhibit a ticking noise at idle after an engine oil change. It is often referred to as typewriter noise because of its similarity to the sound of a mechanical typewriter. The noise in question may be heard on some engines when engine temperatures reach 150F (65Å’C) or higher and engine speed is at idle up to approximately 1700 RPMs. It can typically be heard at the front wheel well and is often isolated to the transmission bell housing or oil pan area. The typewriter noise is not detrimental to the engine function or durability and has no short or long term effects on the engine. This an operating characteristic of the 5.0L engine and no repairs should be attempted.
DOR-N3Z7B-032020-03-30. Service bulletin. This SKU is an Oil Dipstick. The customer communication requested return of unsold inventory to inspect the dipstick tube. The dipstick tube inner diameter may be small enough that it prevents installation of the OE dipstick.
SSM 479482019-05-07. Service bulletin. SSM 47948 - 2010-2019 Various Vehicles - Turbocharged Engines - Oil Supply Filter Replacement When Replacing The Turbocharger Or The Turbocharger Oil Supply Tube For 2010-2019 vehicles equipped with turbocharged engines, when diagnosing and/or replacing turbo related concerns, all steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. When specified in the WSM, the turbocharger oil supply filter must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.
SSM 478302019-04-08. Service bulletin. Some 5.0L 4V engines may exhibit a tick/tap/rattle or knock immediately after secondary timing chain tensioner installation. In some cases the secondary timing chain tensioners are not fully released during installation.To confirm, remove both valve covers and inspect the secondary timing chains and tensioners. If the chain is loose fitting and the tensioner does not appear to be extended, using your hand depress the chain/guide and tensioner several times or until the tensioner releases taking up the slack in the chain. If the chain does not have slack, follow Workshop Manual Section 303-00 to diagnose. The Workshop Manual section 303-01C has been updated to reflect the installation releasing process for the secondary timing chain tensioner.
SSM 477972019-04-08. Service bulletin. Some 2009-2017 Expedition/Navigator, 2009-2014 F-150/Mustang, 2008-2009 Sable, 2008-2019 Taurus/Flex/MKT, 2013-2019 Police Interceptor Sedan/Utility, and 2011-2019 Explorer vehicles may exhibit inoperative or intermittent HVAC blower motor function at various fan speed settings. This may be due to a poor electrical connection at the blower motor speed control. If the blower motor speed control is determined to be the causal part, replacement of the electrical connector pigtail harness (14S411) to the blower motor speed control is also recommended to avoid repeat repairs. Refer to Wiring Diagram, Cell 5 for recommended splicing procedures. Refer to Wiring Diagram, Cells 54/55 to obtain the service pigtail connector part number.
SSM 478302019-04-01. Service bulletin. Some 5.0L 4V engines may exhibit a tick/tap/rattle or knock immediately after secondary timing chain tensioner installation. In some cases the secondary timing chain tensioners are not fully released during installation.To confirm, remove both valve covers and inspect the secondary timing chains and tensioners. If the chain is loose fitting and the tensioner does not appear to be extended, using your hand depress the chain/guide and tensioner several times or until the tensioner releases taking up the slack in the chain. If the chain does not have slack, follow Workshop Manual Section 303-00 to diagnose. The Workshop Manual section 303-01C has been updated to reflect the installation releasing process for the secondary timing chain tensioner.
TSB 18-22732018-12-03. Service bulletin. Some 2013-2018 F-150/Expedition/Navigator vehicles may exhibit an intermittent grinding noise coming from the right or left IWE area in 2WD mode. Follow the Service Procedure steps to correct the condition.
TSB 18-23052018-11-19. Service bulletin. Some 2011-2015 F-150 vehicles equipped with a 3.5L EcoBoost engine and built on or before 29-May-2015 may exhibit a ticking/tapping or rattle type noise from the top front cover area of the engine upon initial start-up that may last for 2-5 seconds after a cold soak of 6 hours or more. Follow the Service Procedure steps to correct the condition.
SSM 473942018-07-23. Service bulletin. Some 2013-2018 F-150, 2015-2018 Transit/Expedition, and 2015-2017 Navigator vehicles equipped with a 3.5L EcoBoost engine with greater than 20,000 miles may exhibit a tick type noise from the cylinder block area. This noise may be caused by a cracked piston skirt. The noise can be isolated to a cylinder using a stethoscope or other suitable listening device. Canceling the affected cylinder will reduce or eliminate the noise. If the noise is isolated to a specific cylinder, it is recommended to replace the short block. If the noise cannot be isolated using the methods described, refer to the Workshop Manual (WSM) for diagnosis. A cracked piston skirt does not result in metal contamination of the engine or any related cylinder head damage. Prior approval for short block replacement is not required under new vehicle limited warranty coverage.