WenmarOpen by Wenmar Pro

Service bulletin SB-10152

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
TypeService bulletin
NHTSA id10033904
Published by NHTSA2010-09-29
Manufacturer's numberSB-10152
Manufacturer's date2010-05-01
NHTSA componentSTEERING:ELECTRIC POWER ASSIST SYSTEM; STEERING:HYDRAULIC POWER ASSIST SYSTEM

NHTSA's summary

BUICK: UPDATE FOR INVENTORY AND CUSTOMER VEHICLES POWER STEERING LINE FITTING POSITIONED INCORRECTLY-EXPIRES WITH BASE WARRANTY. PROCEDURE TO INSPECT THE POSITION OF THE POWER STEERING LINE BANJO FITTING LOCKING DEVICE ON CERTAIN VEHICLES EQUIPPED WITH A 2.4L 4 CYLINDER ENGINE (LAF). *PE

The document

No address for NHTSA's copy can be built for this communication. Ask the dealer for it by the manufacturer's number.

Components

Steering, Power steering

Vehicles listed
BUICK LACROSSE2010
BUICK REGAL2011

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Other bulletins for the same vehicles and component
PIT5076C2023-12-26. Service bulletin. Learning Issues When Repairing Service Stability/Traction Message.
13-02-32-001B2018-05-29. Service bulletin. This technical bulletin provides a procedure to repair any power steering leak that may be caused from extremely low temperatures and use the recommended fluid.
13-02-32-001C2018-05-29. Service bulletin. This technical bulletin provides a procedure to repair any power steering leak that may be caused from extremely low temperatures and use the recommended fluid.
12-02-32-002A2018-04-23. Service bulletin. This technical bulletin provides a revision for 12-02-32-002 to add the 2013-2014 model years, add noise as a possible condition and add a Note in the Instructions section.
13-02-32-001A2018-04-23. Service bulletin. This technical bulletin provides a revision for 13-02-32-001 to update the models information.
PIT5076C2017-08-15. Service bulletin. This Preliminary Information communication advises the technician to insure that global diagnostic service 2 diagnostic packages are up to date prior to learning the steering angle sensor for a diagnostic trouble code C710 symptom code 71 set in the electronic brake control module or the power steering control module. When rechecking for diagnostic trouble codes a U0074 U0077, U0180D, U01293, U0126, U0125, C0186, C0196, or C0287 are set and will not clear diagnose the Chassis bus. If no fault is found in the chassis bus check for an multiple diagnostic interface to data link connector issue. Technician is to try a different multiple diagnostic interface cable and attempt the steering angle sensor learn again following service information instruction then try to clear the codes again.
PIC5598J2017-08-15. Service bulletin. This Preliminary Information communication advises the technician that the part restriction on the electric power steering module for NJ1 part numbers has ended. Dealer can order parts directly through your parts department.
13-02-32-001D2017-08-15. Service bulletin. This technical bulletin provides a procedure to flush and bleed the power steering system to correct a condition of power steering noise or fluid leak from power steering pump, gear or high pressure hose during extreme low temperature conditions.
PIP4716F2017-08-15. Service bulletin. This Preliminary Information communication provides information to the technician about vehicles that may have a short, sharp rattle noise from the front of the engine at start up. Technician may find Diagnostic Trouble Codes P0011 P0014 P0016 or P0017. Technician will need to inspect the engine belt. If the vehicle is equipped with a hydraulic power steering, technician will need to verify the power steering pulley outer edge is aligned flush with shaft and repair as needed. If pulley alignment is correct or vehicle does not have hydraulic steering, replace the engine belt. If the noise is still present and it is coming from the cam actuators they will need to be replaced.
SB-16-NA-1092016-08-06. Service bulletin. "THIS TECHNICAL BULLETIN PROVIDES A PROCEDURE TO INSPECT THE STEERING GEAR FOR A NORMAL CONDITION OF GREASE OR SEALANT ON EXTERIOR CASE OF GEAR DUE TO THE MANUFACTURING PROCESS."