{"vehicle":{"id":"1998_bmw_k-1200-rs","year":1998,"make":"BMW","model":"K 1200 RS"},"may_apply":true,"as_of":{"us":"2026-10-19","ca":"2026-10-19"},"recalls":[{"source":"tc","country":"ca","campaign":"2000219","date":"2000-10-05","manufacturer":null,"component":"Engine","summary":"On certain vehicles, the snap ring which retains the cover for the oil thermostat element in the thermostat housing, may not have been completely seated during production.  The oil thermostat housing is located in the oil pump intermediate flange.  Should the cover loosen or detach, the entire volume of oil could escape from the engine in a relatively short time. In addition to significant engine damage, oil could travel along the engine cover and ultimately contact the rear tire.  This could result in loss of traction and possible loss of vehicle control.  Correction:  Snap ring will be inspected to make sure that it is fully seated.  If the snap ring is not fully seated, the complete fuel pump intermediate flange will be replaced.","mfr_campaign":"RC2000-219","units":202,"do_not_drive":null,"park_outside":null,"notification":"Safety Mfr","match":"exact","models":["K1200RS"],"built_from":null,"built_to":null,"url":"https://open.wenmarpro.com/recalls/tc/2000219"},{"source":"tc","country":"ca","campaign":"2000218","date":"2000-10-05","manufacturer":null,"component":"Engine","summary":"On certain motorcycles, the cylinder head sealing plugs, covering holes in the area of the spark plugs, may not be fully seated.  If either or both of the sealing plugs were to detach from their mounting point during vehicle operation, coolant could escape from the holes, travel along the engine cover and contact the rear tire.  This could result in loss of traction and possible loss of vehicle control.  Correction:  Sealing plugs will be replaced with stainless steel plugs.","mfr_campaign":"RC2000-218","units":29,"do_not_drive":null,"park_outside":null,"notification":"Safety Mfr","match":"exact","models":["K1200RS"],"built_from":null,"built_to":null,"url":"https://open.wenmarpro.com/recalls/tc/2000218"},{"source":"nhtsa","country":"us","campaign":"00V266000","date":"2000-09-12","manufacturer":"BAYERISCHE MOTOREN WERKE","component":"ENGINE AND ENGINE COOLING:ENGINE","summary":"VEHICLE DESCRIPTION:   MOTORCYCLES.  THE CYLINDER HEAD CONTAINS TWO SEALING PLUGS COVERING HOLES IN THE AREA NEAR THE SPARK PLUGS.  ONE OR BOTH PLUGS MAY NOT HAVE BEEN FULLY SEATED DURING VEHICLE ASSEMBLY.  EITHER OR BOTH OF THE SEALING PLUGS COULD LOOSEN OR COMPLETELY DETACH FROM THEIR MOUNTING POINT DURING VEHICLE OPERATION.","mfr_campaign":null,"units":188,"do_not_drive":false,"park_outside":false,"notification":null,"match":"exact","models":["K1200RS"],"built_from":"1997-03-20","built_to":"1997-04-14","url":"https://open.wenmarpro.com/recalls/nhtsa/00V266000"},{"source":"nhtsa","country":"us","campaign":"00V264000","date":"2000-09-12","manufacturer":"BAYERISCHE MOTOREN WERKE","component":"ENGINE AND ENGINE COOLING:ENGINE","summary":"VEHICLE DESCRIPTION:   MOTORCYCLES.  A SPRING-LOADED THERMOSTATIC ELEMENT IN THE OIL THERMOSTAT HOUSING IS HELD IN PLACE BY A COVER THAT IS RETAINED BY A SNAP RING.  THE SNAP RING MAY NOT HAVE BEEN PROPERLY INSTALLED DURING PRODUCTION.  DURING VEHICLE OPERATION, THE SNAP RING COULD UNSEAT, ALLOWING THE COVER TO LOOSEN OR DETACH, RESULTING IN LOSS OF THE ENTIRE OIL VOLUME.","mfr_campaign":null,"units":2368,"do_not_drive":false,"park_outside":false,"notification":null,"match":"exact","models":["K1200RS"],"built_from":"1997-02-01","built_to":"1999-08-31","url":"https://open.wenmarpro.com/recalls/nhtsa/00V264000"},{"source":"tc","country":"ca","campaign":"1999005","date":"1999-01-14","manufacturer":null,"component":"Fuel System","summary":"On certain vehicles, deformation of the fuel tank when the vehicle is operated in high ambient temperature conditions could cause a gap to form between the fuel tank mounting surface and the fuel pump gasket.  This could result in fuel leakage and the possibility of fire.  Correction:  The fuel pump to tank gasket will be replace with an improved gasket that will prevent fuel leakage from the fuel pump/tank interface should tank deformation occur in high temperature conditions.","mfr_campaign":null,"units":88,"do_not_drive":null,"park_outside":null,"notification":"Safety Mfr","match":"exact","models":["K1200RS"],"built_from":null,"built_to":null,"url":"https://open.wenmarpro.com/recalls/tc/1999005"},{"source":"nhtsa","country":"us","campaign":"98V258000","date":"1998-10-14","manufacturer":"BAYERISCHE MOTOREN WERKE","component":"FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY","summary":"VEHICLE DESCRIPTION:  MOTORCYCLES.  DURING EXTENDED OPERATION IN HIGH AMBIENT TEMPERATURE CONDITIONS, THE AREA OF THE PUMP MOUNTING SURFACE OF THE FUEL TANK CAN DEFORM, FORMING A GAP BETWEEN THE TANK MOUNTING SURFACE AND THE GASKET, ALLOWING FUEL TO ESCAPE FROM THE TANK AT THAT AREA.","mfr_campaign":null,"units":1000,"do_not_drive":false,"park_outside":false,"notification":null,"match":"exact","models":["K1200RS"],"built_from":"1997-01-01","built_to":"1997-10-31","url":"https://open.wenmarpro.com/recalls/nhtsa/98V258000"},{"source":"nhtsa","country":"us","campaign":"97V134000","date":"1997-08-08","manufacturer":"BAYERISCHE MOTOREN WERKE","component":"SERVICE BRAKES, HYDRAULIC","summary":"VEHICLE DESCRIPTION:  MOTORCYCLES.    THE ADJUSTING SCREW FOR THE PRESSURE POINT OF EITHER THE BRAKE OR CLUTCH LEVERS MAY NOT BE SUFFICIENTLY TIGHT, DUE TO GREASE CONTAMINATION OF THE THREADS.","mfr_campaign":null,"units":973,"do_not_drive":false,"park_outside":false,"notification":null,"match":"exact","models":["K1200RS"],"built_from":"1997-03-01","built_to":"1997-08-30","url":"https://open.wenmarpro.com/recalls/nhtsa/97V134000"}],"lookup":{"nhtsa":"https://www.nhtsa.gov/recalls","tc":"https://wwwapps.tc.gc.ca/Saf-Sec-Sur/7/VRDB-BDRV/search-recherche/menu.aspx?lang=eng","maker":null},"attribution":["Contains information licensed under the Open Government Licence – Canada."]}