Transport Canada recall 2026019
A recall listed here may apply to a vehicle of this year, make and model. Only the manufacturer can say whether it applies to one vehicle: check the VIN with the official lookups.
| Published by | Transport Canada (Canada) |
|---|---|
| Campaign number | 2026019 |
| Manufacturer's number | 26C02 |
| Reported | 2026-01-21 |
| Component | Structure |
| Notification type | Compliance Mfr |
| Units potentially affected | 5 |
What is wrong
Issue:
On a small number of vehicles, the windshield may not be properly attached and could separate from the vehicle in a crash.
Safety Risk:
A windshield that detaches in a crash could create an increased risk of injury.
Corrective Actions:
Ford will notify owners by mail and advise you to take your vehicle to a dealership to reinstall the windshield.
| 2026 FORD EXPLORER |
|---|
A vehicle with no link is not in this site's catalog, which covers cars, multipurpose vehicles and trucks by model year. The campaign is from data as of 2026-10-19.
Bulletins for the same vehicles and component
| SSM 55186 | 2026-09-21. Service bulletin. Some 2026 Explorer vehicles may exhibit wind noise and/or water intrusion from the panoramic roof panel glass seal. Inspection may find that the seal is rolled or separated from the glass. The seal is not serviceable separately from the glass. To correct this condition, replace the panoramic roof panel glass assembly. Refer to Workshop Manual, Section 501-11 > Removal and Installation > Panoramic Roof Panel Glass. For claiming, use causal part 78500A18 and labor operation 50282BG. |
|---|---|
| RGTM-26.AF Expl&Aviator | 2026-09-01. Over-the-air update. Quality improvements include: -Rear Gate latch calibration update to permit unlatching via the release button when the system has lost position memory and is stuck in a middle-latch position |
| SSM 55060 | 2026-08-04. Service bulletin. Some 2024-2026 Explorer vehicles built on or before 27-Feb-2026 and equipped with the panoramic glass roof may exhibit an uneven gap at the front edge of the roof opening panel shield when fully closed. The gap is an appearance issue only, but may allow outside light to pass through the opening. A new gap hider seal has been released to correct this condition (service part number SB5Z-7851884-A). Adjustment or replacement of the glass, shade or headliner assembly is not necessary. The new seal is installed directly onto the existing vertical flange that is present and visible at the front of the opening when the shade is opened. Once installed, the front edge of the shade will press against the new seal when fully closed. To install, center the seal in the opening with the flexible material facing the power shade and press the seal u-channel over the vertical flange. Explorer vehicles built on or after 27-Feb-2026 have the seal already installed and can be referenced if necessary. Once the seal is installed, perform the shield/shade initialization procedure in Workshop Manual (WSM), Section 501-05 > Gen |
| SSM 54882 | 2026-06-03. Service bulletin. Some 2025-2026 Explorer/Aviator vehicles may exhibit a no crank/no start/discharged battery condition with diagnostic trouble codes (DTC) B144D:29, B144E:29, B1555:29, B1556:29 and/or U3003:16 stored in the rear gate trunk module (RGTM). The power liftgate may also be inoperative. This may be due to water intrusion into the left and/or right power liftgate motors caused by a loose grommet on the electrical harness at the body pass-through. To correct this condition, install a new power liftgate motor corresponding to the DTC(s) set in the RGTM (B144D:29/B144E:29 Ýleft¨ or B1555:29/B1556:29 Ýright¨). To prevent water intrusion into the new liftgate motor, make sure the grommet on the new motor is seated properly by pushing on the grommet at the body pass-through until it clicks into place. For claiming, use causal part 14B351 (Explorer) or 14B350 (Aviator) and labor operations 12651D and 14350AL (left) or 14350AR (right) or 14350AT (both) <br /><br /> If a vehicle with this concern exhibits water intrusion, corrosion, or unseated grommets in or around the liftgate motor, submit a Global Concern Report |
| SSM 54829 | 2026-05-19. Service bulletin. Some 2024-2026 Nautilus and 2025-2026 Explorer/Aviator vehicles equipped with power autofold exterior mirrors may exhibit concerns with the passenger mirror not automatically folding in or out at times, while the driver side mirror automatically folds properly. This may be due to the software in the driver door module (DDM) and passenger door module (PDM). To correct the condition, reprogram the DDM and PDM using the latest software level of the Ford Diagnosis and Repair System (FDRS) scan tool. For claiming, use causal part 14B291 and labor operation MT14B291SSM up to 0.4 hours. |
| SSM 54800 | 2026-05-14. Service bulletin. Some 2025-2026 Explorer/Aviator and 2026 Expedition/Navigator vehicles may exhibit an intermittent inoperative remote start feature using either the key fobs or the Ford/Lincoln App. This may be due to the software in the body control module (BCM). After replicating the concern, use the Ford Diagnosis and Repair System (FDRS) to monitor the RMTSTRT_F_ARB_LST and RMTSTRT_F_TRGT_NM parameter identification (PIDS) in the BCM. If both PID values show "true" in any of the last 5 saved values, engineering is currently working on a solution for this condition that is expected in Q4 2026. Schedule service appointments for customers once the repair becomes available. If either of the BCM PID values do not show "true" in any of the saved values, refer to Workshop Manual (WSM), Section 501-14 Handles, Locks, Latches, Entry Systems > Diagnosis and Testing > Locks, Latches and Entry Systems > Pinpoint Test R (Explorer/Aviator)/Pinpoint Test V (Expedition/Navigator) for normal diagnostics and repair as necessary outside of this article. For claiming, use causal part 15604 and labor operations 12651D and 12651D45 |
| SSM 54601 | 2026-02-27. Service bulletin. Ford and Lincoln vehicles equipped with wired keyless entry keypad systems and accessory wireless keyless entry keypad systems may or may not come with a wallet card containing the master code. Unlike the integrated wired keypad, the accessory wireless keypad master code cannot be retrieved from the vehicle using a diagnostic scan tool or from the label printed on the body control module (BCM). The Factory Keyless Entry Code application within the diagnostic scan tool will not provide an applicable master code for the accessory wireless keypad. If the wallet card for an accessory keypad is not available, the "Wireless RF Keypad Diagnosis Guide" can be referenced and provides direction on how to retrieve the master code. This guide is located under the Workshop Manual tab > Accessories > Installation > Wireless RF Keypad Diagnosis Guide > PPT C > Step C2.<br /><br /> Note: The only available keypad for some vehicles from the assembly plant is the accessory wireless keyless entry keypad. The integrated wired keypad cannot be installed on vehicles not equipped from the factory with a wired keyless entry k |
| SSM 54516 | 2026-01-27. Service bulletin. 2020-2026 Police Interceptor Utility vehicles may require level III ballistic panels to be replaced due to broken mounting tabs. Individual level III ballistic panel mounting tab service parts are now available: right-hand (78201B68) and left-hand (78201B69). Replacement of the level III ballistic panel assembly is not required for this condition. Level IV ballistic panels do not have removable mounting tabs and still require complete panel replacement. Level III vs level IV ballistic panels can be identified by a large roman numeral label on the panel or by the vehicle window sticker if equipped. |
A bulletin is the manufacturer's note to its dealers. It is not part of this recall.
Check one vehicle officially
Contains information licensed under the Open Government Licence – Canada.