Transport Canada recall 2021373
A recall listed here may apply to a vehicle of this year, make and model. Only the manufacturer can say whether it applies to one vehicle: check the VIN with the official lookups.
| Published by | Transport Canada (Canada) |
|---|---|
| Campaign number | 2021373 |
| Manufacturer's number | PM983 |
| Reported | 2021-06-11 |
| Component | Powertrain |
| Notification type | Safety Mfr |
| Units potentially affected | 207 |
What is wrong
Issue:
On certain vehicles equipped with a manual transmission, the gear selector cable could come loose. If this happens, the driver may not be able to shift the transmission into gear, or may unintentionally shift into the wrong gear. This could cause sudden and unexpected vehicle movements.
Safety Risk:
Sudden and unexpected movement of the vehicle could increase the risk of a crash.
Corrective Action:
Nissan will notify owners by mail and instruct you to take your vehicle to a dealer to replace the transmission control assembly.
| 2020 NISSAN SENTRA |
|---|
A vehicle with no link is not in this site's catalog, which covers cars, multipurpose vehicles and trucks by model year. The campaign is from data as of 2026-10-19.
Bulletins for the same vehicles and component
| NTB24-022 | 2024-04-06. Service bulletin. CVT SUB-ASSEMBLY SERVICE PARTS ARE NOW AVAILABLE SERVICE INFORMATION The CVT Belt & Pulley (sub-assembly) Kit is now available to order. The sub-assembly kit part numbers and other parts needed, if a repair is indicated, are listed in PARTS INFORMATION. • This bulletin does not include diagnostic or service procedure information. • Refer to the ESM for necessary diagnostic information before performing a CVT repair. |
|---|---|
| NTB23-030 | 2023-05-06. Service bulletin. CVT SHIFT SELECTOR LEVER KNOB REMOVAL AND INSTALLATION SERVICE INFORMATION If the CVT Shift Selector Lever Knob needs to be removed or installed for any reason, refer to the SERVICE PROCEDURE in this bulletin, beginning on page 2. |
| NTB21-013B | 2023-04-10. Service bulletin. PREVENT FRONT AXLE THREAD DAMAGE DURING NUT REMOVAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. |
| NTB12-055J | 2023-04-06. Service bulletin. CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. |
| NTB22-101 | 2022-12-06. Service bulletin. DRIVE SHAFT BOOT SERVICE INFORMATION SERVICE INFORMATION If a Drive Shaft (Axle Shaft) Boot on an APPLIED VEHICLE is found to be leaking grease, AND There is no abnormal noise or obvious CV Joint risk due to water intrusion and/or complete grease loss, check for REPAIR KIT-DUST BOOT (CV Joint Boot Kit) availability. • If there is a REPAIR KIT-DUST BOOT (CV Joint Boot Kit) available for the vehicle being repaired, do NOT replace the axle. Install a new boot kit following the procedure in the ESM. o Refer to the ESM: TRANSMISSION & DRIVELINE > FRONT AXLE > REMOVAL AND INSTALLATION > FRONT DRIVE SHAFT BOOT o If the complete axle (drive shaft) is replaced when only a new boot is required, the over-repair may be charged back to the dealer. • If there is NOT a REPAIR KIT-DUST BOOT (CV Joint Boot Kit) available for the vehicle being repaired, refer to the ESM for further diagnostic information. IMPORTANT: When servicing vehicles with staked axle nuts, refer to NTB21-013 to prevent Drive Shaft thread damage. |
| NTB21-013A | 2022-10-07. Service bulletin. PREVENT FRONT AXLE THREAD DAMAGE DURING NUT REMOVAL This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. |
| NTB12-055I | 2022-10-07. Service bulletin. CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. |
| NTB12-055H | 2021-07-10. Service bulletin. CLICKING NOISE FROM FRONT OR REAR AXLE DURING TAKE-OFF/ACCELERATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. |
| NTB21-013 | 2021-03-06. Service bulletin. PREVENT FRONT AXLE THREAD DAMAGE DURING NUT REMOVAL SERVICE INFORMATION If an Applied Vehicle needs to have a front axle nut removed, for any reason, the staking of the nut into the axle keyway must first be removed. The essential tool (part number # J-52982, Figure 1) required to remove the nut staking, is called out as a “Cape Chisel” in the Electronic Service Manual (ESM), and must be used to prevent thread damage to the axle (see Figure 2 on page 2). • The Cape Chisel arrived at dealers in December of 2020. • Damaged threads, due to improper removal of the stake placed in the nut, will not be covered by warranty. For information on using the Cape Chisel, refer to the Electronic Service Manual (ESM): Section TRANSMISSION & DRIVELINE > FRONT AXLE > REMOVAL AND INSTALLATION > FRONT DRIVE SHAFT > LH/RH. |
| NTB20-055 | 2020-08-09. Service bulletin. 2020 SENTRA; A/T SHIFT LOCK AND REMOTE START INOPERATIVE WITH NEW BCM SERVICE PART SERVICE INFORMATION After installing a new BCM service part, if the Intelligent Key UNLOCK button is pressed before performing the configuration with CONSULT-III plus, certain BCM configuration parameters will be permanently locked in the default setting; one of these parameters is Remote Engine Start (RES). • The default setting for Remote Engine Start is WITHOUT. • The RES function WILL BE permanently disabled if the UNLOCK button is pressed BEFORE the BCM service part is configured. IMPORTANT: To avoid permanently disabling the RES feature after replacing the BCM, the configuration procedure must be performed first so that all of the vehicle features operate correctly. Avoid pressing the UNLOCK button on the Intelligent Key after a BCM replacement. Wait until the configuration process has completed and the default configuration has been overwritten with the correct data before pressing any Intelligent Key buttons. Things to remember when replacing a BCM: • It is not necessary to register Intelligent Keys to a new BCM. • Never press the UNLOCK button on the Intelligent Key until the configuration settings step has been completed. • Complete the configuration of the BCM either manually, or by downloading saved configuration from the previous BCM (stored in CONSULT-III plus). |
A bulletin is the manufacturer's note to its dealers. It is not part of this recall.
Check one vehicle officially
Contains information licensed under the Open Government Licence – Canada.