Transport Canada recall 2019337
A recall listed here may apply to a vehicle of this year, make and model. Only the manufacturer can say whether it applies to one vehicle: check the VIN with the official lookups.
| Published by | Transport Canada (Canada) |
|---|---|
| Campaign number | 2019337 |
| Manufacturer's number | 3819F |
| Reported | 2019-07-05 |
| Component | Seats And Restraints |
| Notification type | Safety Mfr |
| Units potentially affected | 2945 |
What is wrong
Issue:
The material on the driver and front passenger seatbacks may not be installed correctly. This could cause it to in interfere with the release button for the head restraint. As a result, the button could be stuck in the ‘release’ position and allow the head restraint to move up and down freely. In a crash, this could allow the head restraint to detach.
Safety Risk:
A head restraint that does not remain in place in a crash could create a risk of injury.
Corrective Actions:
Mazda will notify owners by mail and instruct them to take their vehicle to a dealership to install a plastic spacer at the bottom of the head restraint lock release button.
| 2019 MAZDA MAZDA3 |
|---|
A vehicle with no link is not in this site's catalog, which covers cars, multipurpose vehicles and trucks by model year. The campaign is from data as of 2026-10-19.
Bulletins for the same vehicles and component
| 09-016-26a | 2026-08-04. Service bulletin. This bulletin supersedes the previously issued bulletin(s) listed below. The changes are noted in Red. 09-016/26 05/06/26 DESCRIPTION Some customers may complain that the seat warmer does not operate when turning the ignition on while the seat is warm but when turning the ignition off then on again, the seat warmer begins to operate appropriately. DTCs “B1030:13” and/or “B1032:13” are stored. This is caused by the seat warmers fail-safe mode which prevents it from working during the initial drive cycle. To correct this issue, the seat warmer has been modified to optimize the temperature control. B1030:13 Seat warmer unit (LH) circuit malfunction (Heater side) B1032:13 Seat warmer unit (RH) circuit malfunction (Heater side) Customers having this concern should have their vehicle repaired using the following repair procedure. REPAIR PROCEDURE 1. Verify the customer concern. 2. Remove the front seat cushion trim and the front seat back trim for both the driver and passenger seats according to the instructions in MGSS. |
|---|---|
| 09-016-26 | 2026-06-02. Service bulletin. DESCRIPTION Some customers may complain that the seat warmer does not operate when turning the ignition on while the seat is warm but when turning the ignition off then on again, the seat warmer begins to operate appropriately. DTCs “B1030:13” and/or “B1032:13” are stored. This is caused by the seat warmers fail-safe mode which prevents it from working during the initial drive cycle. To correct this issue, the seat warmer has been modified to optimize the temperature control. B1030:13 Seat warmer unit (LH) circuit malfunction (Heater side) B1032:13 Seat warmer unit (RH) circuit malfunction (Heater side) REPAIR PROCEDURE 1. Verify the customer concern. 2. Remove the front seat cushion trim and the front seat back trim for both the driver and passenger seats according to the instructions in MGSS. |
| 09-005-25 | 2025-02-05. Service bulletin. Some customers may complain that the seat warmer does not operate when turning the ignition on while the seat is warm but when turning the ignition off then on again, the seat warmer begins to operate appropriately. DTCs “B1030:13” and/or “B1032:13” are stored. This is caused by the seat warmers fail-safe mode which prevents it from working during the initial drive cycle. To correct this issue, the seat warmer has been modified to optimize the temperature control. B1030:13 Seat warmer unit (LH) circuit malfunction (Heater side) B1032:13 Seat warmer unit (RH) circuit malfunction (Heater side) |
| 09-012-23b | 2023-08-03. Service bulletin. Some customers may complain that the seat warmer does not operate when turning the ignition on while the seat is warm but when turning the ignition off then on again, the seat warmer begins to operate appropriately. DTCs B1030:13 and/or B1032:13 are stored. This is caused by the seat warmers fail-safe mode which prevents it from working during the initial drive cycle. To correct this issue, the seat warmer has been modified to optimize the temperature control. B1030:13 Seat warmer unit (LH) circuit malfunction (Heater side) B1032:13 Seat warmer unit (RH) circuit malfunction (Heater side) |
| 09-012-23a | 2023-04-04. Service bulletin. Some customers may complain that the seat warmer does not operate when turning the ignition on while the seat is warm but when turning the ignition off then on again, the seat warmer begins to operate appropriately. DTCs “B1030:13” and/or “B1032:13” are stored. This is caused by the seat warmers fail-safe mode which prevents it from working during the initial drive cycle. To correct this issue, the seat warmer has been modified to optimize the temperature control. B1030:13 Seat warmer unit (LH) circuit malfunction (Heater side), B1032:13 Seat warmer unit (RH) circuit malfunction (Heater side) |
| 09-012-23 | 2023-03-03. Service bulletin. Some customers may complain that the seat warmer does not operate when turning the ignition on while the seat is warm but when turning the ignition off then on again, the seat warmer begins to operate appropriately. DTCs “B1030:13” and/or “B1032:13” are stored. This is caused by the seat warmer's fail-safe mode which prevents it from working during the initial drive cycle. To correct this issue, the seat warmer has been modified to optimize the temperature control. B1030:13 Seat warmer unit (LH) circuit malfunction (Heater side), B1032:13 Seat warmer unit (RH) circuit malfunction (Heater side) |
| 09-044-22 | 2022-12-02. Service bulletin. Some customers may complain that the seat warmer does not operate when turning the ignition on while the seat is warm but when turning the ignition off then on again, the seat warmer begins to operate appropriately. DTCs "B1030:13" and/or "B1032:13" are stored. This is caused by the seat warmer's fail-safe mode which prevents it from working during the initial drive cycle. To correct this issue, the seat warmer has been modified to optimize the temperature control. - B1030:13 Seat warmer unit (LH) circuit malfunction (Heater side) - B1032:13 Seat warmer unit (RH) circuit malfunction (Heater side) |
| SA-009-21 | 2021-02-06. Service bulletin. Some customers may complain that the seat warmer turns off after 10 minutes in manual mode and will not turn back on until the vehicle is restarted. DTC B1030:13 (Seat warmer unit (LH) circuit malfunction (heater side)) may also be stored. This may be caused by a faulty seat warmer control unit (A). |
| 09-007-20-3674a | 2021-01-05. Service bulletin. At PDI or when new vehicle is delivered, some customers may complain about wrinkles on the leather seat cushion and/or seat back surface. Customers having this concern should have their vehicle repaired by a qualified upholstery repair specialist using the following repair procedure. |
| 09-027-20-3703 | 2020-09-01. Service bulletin. Some customers may complain about a squeaking noise when sliding the front seat. This is caused by a deformed front seat side bolster that rubs on the rear console lid. To eliminate this concern, the shape of the front seats has been changed. |
A bulletin is the manufacturer's note to its dealers. It is not part of this recall.
Check one vehicle officially
Contains information licensed under the Open Government Licence – Canada.