Transport Canada recall 2019300
A recall listed here may apply to a vehicle of this year, make and model. Only the manufacturer can say whether it applies to one vehicle: check the VIN with the official lookups.
| Published by | Transport Canada (Canada) |
|---|---|
| Campaign number | 2019300 |
| Manufacturer's number | 4190019 |
| Reported | 2019-06-17 |
| Component | Powertrain |
| Notification type | Safety Mfr |
| Units potentially affected | 152 |
What is wrong
Issue:
On certain vehicles, the driveshaft may detach from the transmission flange. This could cause a loss of power to the drive wheels.
Safety Risk:
A loss of power to the drive wheels could increase the risk of a crash.
Corrective Actions:
The company will notify owners by mail and instruct them to take their vehicle to a dealer to replace the carbon-fiber driveshaft.
| 2015 MERCEDES-BENZ AMG GT | |
|---|---|
| 2016 MERCEDES-BENZ AMG GT | |
| 2017 MERCEDES-BENZ AMG GT |
A vehicle with no link is not in this site's catalog, which covers cars, multipurpose vehicles and trucks by model year. The campaign is from data as of 2026-10-19.
Bulletins for the same vehicles and component
| LI35.30-P-058566 | 2026-07-14. Service bulletin. Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The noise is heard once in each instance when changing direction of travel. Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to cracking of the microweld between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened. See also LI33.20-P-078406 Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove side shafts 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") with Molykote and leave to dry for "one hour" in removed condition 4. Reinstall side shafts Note: Before using the antifriction coating (Molykote), stir it or shake it thoroughly for (at least 1 minute). |
|---|---|
| CL- Auto Trans Leak | 2026-04-30. Other. The purpose of this letter is to advise you of additional benefits that Mercedes-Benz USA, LLC ("MBUSA") is providing to you regarding your vehicle ownership. What's Included In our continuing efforts to assure the proper performance of Mercedes-Benz vehicles and to enhance the satisfaction of our customers, MBUSA is extending the warranty of the Automatic Transmission on the vehicles listed below. Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, determined that the Automatic Transmission could potentially fail and result in a leak. The warranty of the Automatic Transmission has therefore been extended from the original New Vehicle Limited Warranty of 4 years / 50,000 miles to 8 years / unlimited miles, and applies to the vehicle regardless of ownership This extended warranty applies to the aforementioned condition that necessitates the service and/or replacement of the Automatic Transmission under the New Vehicle Limited Warranty terms and conditions. The following vehicles are included: Any repairs under this warranty extension must be performed by an authorized Mercedes-Benz dealership. This extended warranty does not cover any other components beyond the ones mentioned above, and New Vehicle Limited warranty terms apply, including the exclusions with respect to extra expenses, as identified in the Service and Warranty Information booklet. In the case of failure of any other component other than the aforementioned part beyond the New Vehicle Limited Warranty of 4 years / 50,000 miles, the associated repair will not be covered and will remain your responsibility. |
| EW - Auto Trans Leak | 2026-04-27. Warranty extension. Mercedes-Benz AG (“MBAG”), the manufacturer of Mercedes-Benz vehicles, has extended the warranty on the transmission from the original New Vehicle Limited Warranty of 4 years/50,000 miles to 8 years/unlimited miles on certain Model Year (“MY”) 2016 AMG GT (190 Platform) vehicles. This warranty extension includes the automatic transmission which may leak due to a potential misalignment of the radial shaft seal. This extended limited warranty applies to all aforementioned conditions that necessitate the servicing and or replacement of the automatic transmission under the standard warranty terms and conditions. Please be advised that all automatic transmissions found to be leaking will be replaced The following damage codes and parts can only be claimed for the replacement of the automatic transmission: Damage Code: 27 03E04 Parts: A 190 260 06 00 Transmission A 190 260 05 00 Transmission |
| LI33.30-P-056665 | 2025-06-03. Service bulletin. Complaint Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The clunk is heard once when changing from forward to reverse (and vice versa). Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to micromovement in the connection between the wheel bearing inner race and the joint housing of the side shaft. Note: The collar nut must always be replaced after being loosened and must be tightened to the specified torque. Remedy Coat contact surface of side shaft with wheel bearing with Molykote paint. To do this, proceed as follows: 1. Remove outboard side shafts (extract outer joint gearing from wheel hub) 2. Clean contact surface A (see image file in attachment "Outer joint housing before") before coating with Molykote, using "spirit" (free of dust and grease) 3. Coat contact surface A (see image file in attachment "Outer joint housing after") using Molykote and leave to dry for one hour in removed condition 4. Reinstall side shafts |
| LI27.60-P-077704 | 2024-10-26. Service bulletin. Complaint DSI selection lever module cannot be switched to park position "P" - malfunction of "P" button. Vehicle will shift into park automatically at ignition off or with opening the driver door. Cause Possible causes: 1. Contamination/ingress of dust 2. Short circuit due to ingress of water Note: This repair may not be covered by warranty due to outside influence. Remedy Clean printed circuit board under plastic housing and button "P": 1. Remove DSI (AR27.60-P-0901FRX) 2. Remove housing of DSI (see picture 1) 3. Remove cover around "P" button above printed circuit board (see picture 2) 4. Check printed circuit board: Liquid residues and/or contamination (cf. picture 3) 5. Check "P" button: Water residues and/or contamination (cf. picture 4) 6. Carefully clean the affected areas. We recommend an electrical contact cleaner such as BW-100 or CRC QD Electronic Cleaner as example. 7. Assemble and check for proper function |
| LI27.50-P-049710 | 2019-11-04. Service bulletin. Automatic transmission limp-home mode, fault codes 0717, 0718, 0722, 0723, 2200, 2201, 2204, 2205, 2206, 2207, 2767, 2768, P071700, P071800, P072200, P072300, P276700, P276800 |
| LI27.40-P-058480 | 2019-11-04. Service bulletin. Dual Clutch Transmission leak has been observed. |
| LI27.40-P-058480 | 2019-11-04. Service bulletin. Dual clutch transmission leaking |
| LI54.21-P-061171 | 2018-05-07. Service bulletin. Message in instrument cluster "Measurement of engine oil level not possible" |
A bulletin is the manufacturer's note to its dealers. It is not part of this recall.
Check one vehicle officially
Contains information licensed under the Open Government Licence – Canada.