Transport Canada recall 2016428
A recall listed here may apply to a vehicle of this year, make and model. Only the manufacturer can say whether it applies to one vehicle: check the VIN with the official lookups.
| Published by | Transport Canada (Canada) |
|---|---|
| Campaign number | 2016428 |
| Manufacturer's number | AL26 |
| Reported | 2016-09-02 |
| Component | Powertrain |
| Notification type | Safety Mfr |
| Units potentially affected | 1498 |
What is wrong
On certain vehicles, the transmission wire harness connections may have been improperly crimped. This could cause an unexpected shift to neutral which could result in a loss of motive power, which in conjunction with traffic and road conditions, and the driver's reactions may increase the risk of a crash. Correction: Dealers will update vehicle software to eliminate the potential for an unexpected loss of motive power due to this issue.
| 2015 ACURA TLX |
|---|
A vehicle with no link is not in this site's catalog, which covers cars, multipurpose vehicles and trucks by model year. The campaign is from data as of 2026-10-19.
Bulletins for the same vehicles and component
| BTS-151101 V2 | 2021-05-14. Service bulletin. Replacement TCMs don’t come with trim data. After installation, you need to run a teach-in (hydraulic pressure characteristic calibration) procedure with the HDS. The problem is that A/T DTC P287C (transmission adaptive values not learned) is set, which prevents teach-in. This happens because the TCM is programmed to look for trim data any time the ignition is cycled. If the TCM doesn’t see that trim data, it sets A/T DTC P287C. If any DTCs are set, the TCM won’t initiate teach-in and, as a result, can’t learn the trim data. It’s a classic catch-22 situation. |
|---|---|
| SB-16-012 | 2021-05-13. Service bulletin. BACKGROUND American Honda has made several shift quality improvements in the 2015 and 2016 TLX V6. SYMPTOM There is a sensation of acceleration while coasting down a hill. There is a sensation of a surge while braking. The transmission feels like it stays in gear too long. CORRECTIVE ACTION Update the TCM software. Clear all DTC’s created during the update and do the idle learn procedure. This software update will change the way the transmission shifts. After the update it may take up to 30 miles for the transmission to adapt to the client’s driving habits. |
| B19-003 | 2020-12-09. Service bulletin. Service Bulletin - During a downshift from 9th or 8th gear to 7th gear or lower, a miscalculation in the TCM software causes the MIL to come on with DTC P0716 (input shaft [mainshaft] speed sensor [range/performance]). |
| B20-015 | 2020-11-03. Service bulletin. Service Bulletin - The transmission has intermittent harsh or jerky upshifts with steady acceleration. |
| B19-003 | 2020-10-21. Service bulletin. Service Bulletin - During a downshift from 9th or 8th gear to 7th gear or lower, a miscalculation in the TCM software causes the MIL to come on with DTC P0716 (input shaft [mainshaft] speed sensor [range/performance]). |
| B15-040 | 2020-09-16. Service bulletin. Service Bulletin - Under very specific driving conditions the customer may notice the 2-3 upshift is more pronounced (firmer) than the other shifts. The transmission is working properly and this does not indicate a problem. This is not a durability concern. |
| B20-015 | 2020-09-04. Service bulletin. Service Bulletin - The transmission has intermittent harsh or jerky upshifts with steady acceleration. |
| B19-003 | 2019-09-18. Service bulletin. Service Bulletin - During a downshift from 9th or 8th gear to 7th gear or lower, a miscalculation in the TCM software causes the MIL to come on with DTC P0716 (input shaft [mainshaft] speed sensor [range/performance]). |
| B19-003 | 2019-07-23. Service bulletin. Service Bulletin - During a downshift from 9th or 8th gear to 7th gear or lower, a miscalculation in the TCM software causes the MIL to come on with DTC P0716, input shaft [mainshaft] speed sensor [range/performance]. |
| B19-003 | 2019-06-19. Service bulletin. Service Bulletin - During a downshift from 9th or 8th gear to 7th gear or lower, a miscalculation in the TCM software causes the MIL to come on with DTC P0716, input shaft [mainshaft] speed sensor [range/performance]. |
A bulletin is the manufacturer's note to its dealers. It is not part of this recall.
Check one vehicle officially
Contains information licensed under the Open Government Licence – Canada.