Transport Canada recall 2014114
A recall listed here may apply to a vehicle of this year, make and model. Only the manufacturer can say whether it applies to one vehicle: check the VIN with the official lookups.
| Published by | Transport Canada (Canada) |
|---|---|
| Campaign number | 2014114 |
| Manufacturer's number | 7414D |
| Reported | 2014-04-07 |
| Component | Fuel System |
| Notification type | Safety Mfr |
| Units potentially affected | 3567 |
What is wrong
On certain vehicles, a defect in the fuel tank venting system could allow the fuel tank to be overfilled, causing fuel to enter the charcoal canister and possibly resulting in a fuel leak. Leaking fuel, in the presence of an ignition source, could lead to a fire causing injury and/or damage to property. Correction: Dealers will affect repairs.
| 2014 MAZDA MAZDA6 |
|---|
A vehicle with no link is not in this site's catalog, which covers cars, multipurpose vehicles and trucks by model year. The campaign is from data as of 2026-10-19.
Bulletins for the same vehicles and component
| MT-002-21a | 2021-10-31. Service bulletin. Ethanol is becoming a common additive in gasoline. Gasoline containing ethanol is likely available at your local gasoline station. Typical blends of ethanol include E10 and E85. E10: A blend of 10% ethanol and 90% gasoline. E85: A blend of 85% ethanol and 15% gasoline All Mazda vehicles can run on gasoline containing up to 10% ethanol (E10) but only some 1999-2001 B3000 trucks can run on gasoline with more than 10% ethanol blended. E10 compatible vehicles: All Mazda vehicles. E85 compatible vehicles: 1999-2001 B3000 Mazda trucks with the 8th VIN digit is V. |
|---|---|
| 01-003-17 | 2021-01-25. Service bulletin. When the engine is started for the first time after parking overnight in cold weather (below freezing), some vehicles may exhibit the check engine light on with DTC P0451 (fuel tank pressure sensor: sensor characteristic malfunction) stored in memory. This concern may be caused by an increase in discharge resistance due to water accumulated and frozen in the canister vent hose. |
| 00-003-19-3583 | 2019-03-21. Service bulletin. In support of the new MRT distribution, Mazda will ship to dealers a new Dual Purpose Diagnostic Leak Detector beginning March, 2019. Training videos will be posted to MGSS shortly and Workshop Manual procedures will be revised gradually. |
| 01-005-18-3415 | 2018-05-07. Service bulletin. Some vehicles may experience a rough idle with the check engine light on and DTC P0015 / P0524 stored in memory. P0015:00 - Exhaust CMP timing over-retarded P0524:00 - Engine oil pressure too low This is caused by a drop in engine oil pressure due to a piece of foreign object stuck on the oil pump pressure relief valve or oil control valve (OCV). The temporary entry of the foreign object triggers a check engine light on, but rough idle will not be produced until a later time. |
| RF-16-03R1 | 2018-04-23. Service bulletin. The SKYACTIV®-G 2.5T engine requires a unique oil filter (PY8W-14-302) which is NOT interchangeable with other SKYACTIV® oil filters. The unique oil filter can be identified with two white bands as shown below. |
| 09-048-14-2975 | 2017-05-11. Service bulletin. SOME CUSTOMERS MAY COMPLAIN THAT THE FUEL GAUGE SHOWS EMPTY AND/OR THE DISTANCE-TO-EMPTY ON THE MULTI-INFORMATION DISPLAY (MID) INDICATES “0” WITH A CERTAIN AMOUNT OF FUEL REMAINING IN THE TANK.THIS MAY BE A NORMAL OPERATION OF THE FAIL-SAFE FUNCTION:1.IF FOREIGN MATERIAL (CONTAINED IN A POOR-QUALITY FUEL) ADHERES TO THE FUEL GAUGE SENDER UNIT, THE FAIL-SAFE FUNC-TION INITIATES BY FORCING THE FUEL GAUGE AND THE DISTANCE-TO-EMPTY TO INDICATE “ZERO FUEL AMOUNT”.2.IMMEDIATELY AFTER THE FOREIGN MATERIAL IS DISLODGED BY SHAKING OF THE FUEL DURING DRIVING OR REFUELING, THE FUEL GAUGE WILL RETURN TO A NORMAL READING, BUT THE DISTANCE-TO-EMPTY WILL CONTINUE TO READ “0” UNTIL THE NEXT REFUEL-ING OF 3 US GALLONS (10 LITERS) OR MORE.TO CORRECT THE PROBLEM THE FOLLOWING CHANGE HAS BEEN MADE:1.THERE IS NO MASS-PRODUCTION CHANGE TO PREVENT ADHESION OF FOREIGN MATERIAL TO THE FUEL GAUGE SENDER UNIT. SO THE FACT REMAINS UNCHANGED THAT THE FUEL GAUGE AND THE DISTANCE-TO-EMPTY INDICATE “ZERO FUEL AMOUNT” WHEN FOREIGN MATERIAL ADHERES TO THE FUEL GAUGE SENDER UNIT, AND THE FAIL-SAFE FUNCTION INITIATES.2.TO EQUALIZE THE RECOVERY TIMING FROM THE FAIL-SAFE MODE, THE LOGIC HAS BEEN CHANGED SO THAT THE DISTANCE-TO-EMPTY RECOVERS FROM “0” TO A NORMAL READING IMMEDIATELY AFTER THE FOREIGN MATERIAL IS DISLODGED (AT THE SAME TIME AS THE FUEL GAUGE). |
| 09-048-14-2975A | 2017-05-11. Service bulletin. SOME CUSTOMERS MAY COMPLAIN THAT THE FUEL GAUGE SHOWS EMPTY AND/OR THE DISTANCE-TO-EMPTY ON THE MULTI-INFORMATION DISPLAY (MID) INDICATES “0” WITH A CERTAIN AMOUNT OF FUEL REMAINING IN THE TANK.THIS MAY BE A NORMAL OPERATION OF THE FAIL-SAFE FUNCTION:1.IF FOREIGN MATERIAL (CONTAINED IN A POOR-QUALITY FUEL) ADHERES TO THE FUEL GAUGE SENDER UNIT, THE FAIL-SAFE FUNC-TION INITIATES BY FORCING THE FUEL GAUGE AND THE DISTANCE-TO-EMPTY TO INDICATE “ZERO FUEL AMOUNT”.2.IMMEDIATELY AFTER THE FOREIGN MATERIAL IS DISLODGED BY SHAKING OF THE FUEL DURING DRIVING OR REFUELING, THE FUEL GAUGE WILL RETURN TO A NORMAL READING, BUT THE DISTANCE-TO-EMPTY WILL CONTINUE TO READ “0” UNTIL THE NEXT REFUEL-ING OF 3 US GALLONS (10 LITERS) OR MORE.TO CORRECT THE PROBLEM THE FOLLOWING CHANGE HAS BEEN MADE:1.THERE IS NO MASS-PRODUCTION CHANGE TO PREVENT ADHESION OF FOREIGN MATERIAL TO THE FUEL GAUGE SENDER UNIT. SO THE FACT REMAINS UNCHANGED THAT THE FUEL GAUGE AND THE DISTANCE-TO-EMPTY INDICATE “ZERO FUEL AMOUNT” WHEN FOREIGN MATERIAL ADHERES TO THE FUEL GAUGE SENDER UNIT, AND THE FAIL-SAFE FUNCTION INITIATES.2.TO EQUALIZE THE RECOVERY TIMING FROM THE FAIL-SAFE MODE, THE LOGIC HAS BEEN CHANGED SO THAT THE DISTANCE-TO-EMPTY RECOVERS FROM “0” TO A NORMAL READING IMMEDIATELY AFTER THE FOREIGN MATERIAL IS DISLODGED (AT THE SAME TIME AS THE FUEL GAUGE). |
| 09-048-14 | 2016-03-31. Service bulletin. SUMMARY TO BE PROVIDED ON A FUTURE DATE. |
| 09-048-14 | 2016-03-31. Service bulletin. SUMMARY TO BE PROVIDED ON A FUTURE DATE. |
| SB-01-010-14 | 2014-08-26. Service bulletin. MAZDA: DUE TO HIGH PRESSURE FUEL PUMP NOT GENERATING TARGET FUEL PRESSURE, CAUSED BY MANUFACTURING ERROR, THE CHECK ENGINE LIGHT COMES ON. MODEL 2012-2014. *PE |
A bulletin is the manufacturer's note to its dealers. It is not part of this recall.
Check one vehicle officially
Contains information licensed under the Open Government Licence – Canada.