Transport Canada recall 1999235
A recall listed here may apply to a vehicle of this year, make and model. Only the manufacturer can say whether it applies to one vehicle: check the VIN with the official lookups.
| Published by | Transport Canada (Canada) |
|---|---|
| Campaign number | 1999235 |
| Manufacturer's number | 99085 |
| Reported | 1999-12-22 |
| Component | Emissions |
| Notification type | Compliance Mfr |
| Units potentially affected | 152 |
What is wrong
On certain vehicles, the crankshaft position sensors may fail and cause an intermittent engine chuggle, stall or possible long starting crank time and/or a no-start condition, as well as illumination of the Malfunction Indicator Lamp (MIL). Correction: Dealers will replace both crankshaft position sensors.
| 2000 CADILLAC ELDORADO | |
|---|---|
| 2000 CADILLAC SEVILLE |
A vehicle with no link is not in this site's catalog, which covers cars, multipurpose vehicles and trucks by model year. The campaign is from data as of 2026-10-19.
Bulletins for the same vehicles and component
| 16NA383 | 2019-07-01. Service bulletin. This informational bulletin advises of a new fuel injection kit used for decarbonizing the intake valves, and explains how toptier fuels should be used to reduce carbon build up. |
|---|---|
| PIP4925B | 2019-03-18. Service bulletin. This preliminary information document communicates a tip on the way to diagnose possible induction or exhaust air leaks using the evaporative emission cart smoke machine and ultrasonic leak detector tools. |
| PIP5232A | 2018-05-07. Service bulletin. This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire. |
| PIP5232 | 2018-05-07. Service bulletin. This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire. |
| PIP5232B | 2017-08-15. Service bulletin. This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire. |
| PIT4943D | 2017-08-15. Service bulletin. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay. |
| PIP5232C | 2017-08-15. Service bulletin. This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the coil grounds ring terminal at the engine block for the bank with the concern and repair the wire. |
| 040605008 | 2005-02-14. Service bulletin. AVAILABILITY OF EXHAUST MUFFLER FOR SERVICE. *TT |
A bulletin is the manufacturer's note to its dealers. It is not part of this recall.
Check one vehicle officially
Contains information licensed under the Open Government Licence – Canada.