NHTSA recall 99V302000
A recall listed here may apply to a vehicle of this year, make and model. Only the manufacturer can say whether it applies to one vehicle: check the VIN with the official lookups.
| Published by | NHTSA (United States) |
|---|---|
| Campaign number | 99V302000 |
| Manufacturer's number | 99075 |
| Manufacturer | GENERAL MOTORS CORP. |
| Reported | 1999-10-29 |
| Owners notified | 1999-11-18 |
| Component | FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY:FILLER PIPE AND CAP |
| Units potentially affected | 43218 |
What is wrong
CERTAIN PASSENGER VEHICLES FAIL TO COMPLY WITH REQUIREMENTS OF FMVSS NO. 301, "FUEL SYSTEM INTEGRITY." THE FUEL FILL FITTING IS NOT PROPERLY SECURED TO THE FUEL TANK. IN THAT CONDITION, FUEL LEAKAGE WOULD EXCEED THE PERMISSIBLE AMOUNT IN AN FMVSS TEST. FUEL LEAKS MAY OCCUR, PARTICULARLY AFTER REFUELING OR WHEN THE TANK IS MORE THAN HALF FULL.
What can happen
IF AN IGNITION SOURCE WERE PRESENT, A FIRE COULD OCCUR.
The remedy
DEALERS WILL INSPECT THE FUEL TANK AND REPLACE IT IF NECESSARY.
Notes
GM RECALL NO. 99075. OWNER NOTIFICATION BEGAN NOVEMBER 18, 1999. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT CHEVROLET AT 1-800-222-1020. ALSO CONTACT THE NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION'S AUTO SAFETY HOTLINE AT 1-888-DASH-2-DOT (1-888-327-4236).
| 2000 CHEVROLET MALIBU | Built 1999-04-01 to 1999-09-30. |
|---|
A vehicle with no link is not in this site's catalog, which covers cars, multipurpose vehicles and trucks by model year. The campaign is from data as of 2026-10-19.
Bulletins for the same vehicles and component
| PIT4943D | 2017-08-15. Service bulletin. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay. |
|---|
A bulletin is the manufacturer's note to its dealers. It is not part of this recall.