NHTSA recall 99V100000
A recall listed here may apply to a vehicle of this year, make and model. Only the manufacturer can say whether it applies to one vehicle: check the VIN with the official lookups.
| Published by | NHTSA (United States) |
|---|---|
| Campaign number | 99V100000 |
| Manufacturer | BAYERISCHE MOTOREN WERKE |
| Reported | 1999-05-03 |
| Owners notified | 1999-05-14 |
| Component | SERVICE BRAKES, HYDRAULIC:PEDALS AND LINKAGES |
| Units potentially affected | 31067 |
What is wrong
VEHICLE DESCRIPTION: PASSENGER VEHICLES. IT IS POSSIBLE THAT THE RETAINING CLIP THAT SECURES THE BRAKE BOOSTER PUSHROD TO THE BRAKE PEDAL ARM WAS NOT PROPERLY INSTALLED DURING PRODUCTION. IT IS POSSIBLE FOR THE CLIP TO DETACH FROM THE PIN ON THE BRAKE PEDAL ARM ALLOWING THE PUSHROD TO DISCONNECT FROM THE ARM.
What can happen
IF THIS OCCURS, BRAKING IS NOT POSSIBLE.
The remedy
DEALERS WILL INSPECT THE CLIP FOR TIGHT INSTALLATION AND REPLACE THE CLIP IF IT IS LOOSE.
Notes
OWNER NOTIFICATION BEGAN MAY 14, 1999.OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT BMW AT 1-800-831-1117.ALSO CONTACT THE NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION'S AUTO SAFETY HOTLINE AT 1-888-DASH-2-DOT (1-888-327-4236).
| 1999 BMW 323I | Built 1998-06-01 to 1999-03-08. |
|---|---|
| 1999 BMW 328I | Built 1998-06-01 to 1999-03-08. |
A vehicle with no link is not in this site's catalog, which covers cars, multipurpose vehicles and trucks by model year. The campaign is from data as of 2026-10-19.
Bulletins for the same vehicles and component
| B340414 | 2021-05-24. Service bulletin. Diagnosis of Compound Brake System Complaints in M Vehicles: 1. Visible cracks are caused by high thermal stresses during rapid heating and cooling of the brake discs. Braking from high speed with cold brake components (less than 212 degrees F) increases the likelihood of cracks to form. |
|---|---|
| 340414 | 2018-11-13. Service bulletin. Diagnosis of Compound Brake System Complaints in M Vehicles. INFORMATION 1. Visible cracks are caused by high thermal stresses during rapid heating and cooling of the brake discs. Braking from high speed with cold brake components (less than 212 degrees F) increases the likelihood of cracks to form. These surface hairline cracks are usually spread over the entire brake disc friction area, and have no negative influence on the durability or braking performance. The rotors should not be replaced only for their appearance reasons. When performing routine service on the brake system (pad replacement due to wear), the brake discs should be replaced if surface cracks are found to be greater than 13 mm, or if the brake disc thickness is below the minimum thickness. Always replace brake discs in pairs (per axle). Install new brake pads when replacing discs. By doing this, the service life of the friction pad surface is increased, and an even material loss is ensured. 2. Vibrations and/or steering wheel torsional vibrations during braking are caused by applying the brakes on discs with minimal to heavy corrosion. These vibrations are most noticeable when braking from high speeds with cold brake components (less than 212 degrees F), and will diminish with normal everyday operation. Parts replacement is not required. 3. After high brake loads, running noises can be heard when applying the brakes, and may also be heard to a limited extent after the brakes are released. (See the note in the Owner's Manual). These noises are reduced during normal everyday operation, due to further erosion of the brake pad friction lining. Visible surface cracks or craterlike recesses on the brake pad surface are caused by a minor difference in the material of the pad lining, which will decrease with further operation and should not be replaced due to their appearance. |
| B340414 | 2018-11-05. Service bulletin. Diagnosis of Compound Brake System Complaints in M Vehicles This Service Information bulletin supersedes SI 34 04 14 dated December 2014. Designates changes to the bulletin. INFORMATION 1.Visible cracks are caused by high thermal stresses during rapid heating and cooling of the brake discs. Braking from high speed with cold brake components (less than 212 degrees F) increases the likelihood of cracks to form. These surface hairline cracks are usually spread over the entire brake disc friction area, and have no negative influence on the durability or braking performance. The rotors should not be replaced only for their appearance reasons.When performing routine service on the brake system (pad replacement due to wear), the brake discs should be replaced if surface cracks are found to be greater than 13 mm, or if the brake disc thickness is below the minimum thickness. Always replace brake discs in pairs (per axle). Install new brake pads when replacing discs. By doing this, the service life of the friction pad surface is increased, and an even material loss is ensured. 2. Vibrations and/or steering wheel torsional vibrations during braking are caused by applying the brakes on discs with minimal to heavy corrosion. These vibrations are most noticeable when braking from high speeds with cold brake components (less than 212 degrees F), and will diminish with normal everyday operation. Parts replacement is not required. 3.After high brake loads, running noises can be heard when applying the brakes, and may also be heard to a limited extent after the brakes are released. (See the note in the Owner's Manual). These noises are reduced during normal everyday operation, due to further erosion of the brake pad friction lining. Visible surface cracks or craterlike recesses on the brake pad surface are caused by a minor difference in the material of the pad lining, which will decrease with further operation and should not be replaced due to their appearance. |
| SI-B-34-11-08 | 2009-12-09. Service bulletin. BMW VEHICLES: TEILECLEARING FOR DYNAMIC STABILITY CONTROL (DSC). A PART REPLACEMENT AUTHORIZATION MUST BE OBTAINED BY SUBMITTING A TC CASE IN PUMA BEFORE ANY OF THE FOLLOWING DSC COMPONENTS ARE REPLACED UNDER WARRANTY FOR THE VEHICLES LISTED IN THE MODEL SECTION OF THIS BULLETIN: DSC CONTROL MODULE, DSC HYDRO UNIT, AND YAW RATE SENSOR. NO MODEL YEARS LISTED. *PE |
A bulletin is the manufacturer's note to its dealers. It is not part of this recall.