NHTSA recall 94V135000
A recall listed here may apply to a vehicle of this year, make and model. Only the manufacturer can say whether it applies to one vehicle: check the VIN with the official lookups.
| Published by | NHTSA (United States) |
|---|---|
| Campaign number | 94V135000 |
| Manufacturer | NISSAN NORTH AMERICA, INC. |
| Reported | 1994-07-25 |
| Owners notified | 1994-08-19 |
| Component | SERVICE BRAKES, HYDRAULIC:BRAKE FLUID LOW WARNING: LAMP |
| Units potentially affected | 7500 |
What is wrong
THE INSTRUMENT PANEL BRAKE WARNING LIGHT WILL NOT ILLUMINATE WHEN THE BRAKE FLUID LEVEL IN THE MASTER CYLINDER DROPS SUFFICIENTLY TO ACTIVATE THE LOW LEVEL SWITCH DUE TO AN IMPROPERLY WIRED DIODE, REQUIRED BY FMVSS NO. 105, "HYDRAULIC BRAKE SYSTEMS."
What can happen
CONSEQUENCE OF NON-COMPLIANCE: THERE WOULD BE NO INDICATION TO THE DRIVER OF THE VEHICLE THAT BRAKE FLUID WAS LOW. LOW BRAKE FLUID CAN BE CAUSED BY A LEAK IN THE SYSTEM WHICH MAY RESULT IN PARTIAL OR COMPLETE LOSS OF BRAKES AND AN ACCIDENT.
The remedy
DEALERS WILL CORRECT THE ELECTRICAL CIRCUIT FOR THE BRAKE WARNING SYSTEM SO THAT THE WARNING LAMP WILL ILLUMINATE WHEN THE LOW LEVEL SWITCH IS ACTIVATED.
Notes
SYSTEM: BRAKES; HYDRAULIC; LAMP LIGHT; BRAKE WARNING; FMVSS 105.VEHICLE DESCRIPTION: PASSENGER CARS.NOTE: IF YOUR VEHICLE IS PRESENTED TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND THE REMEDY IS NOT PROVIDED WITHIN A REASONABLE TIME AND FREE OF CHARGE, OR THE REMEDY DOES NOT CORRECT THE DEFECT OR NONCOMPLIANCE, PLEASE CONTACT NISSAN SERVICE CENTER AT 1-800-647-7261. ALSO, CONTACT THE NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION'S AUTO SAFETY HOTLINE AT 1-800-424-9393.
| 1995 NISSAN 240SX | Built 1994-02-01 to 1995-01-01. |
|---|
A vehicle with no link is not in this site's catalog, which covers cars, multipurpose vehicles and trucks by model year. The campaign is from data as of 2026-10-19.
Bulletins for the same vehicles and component
| NTB04094A | 2021-05-10. Service bulletin. If YOU CONFIRM: A vehicle needs to have the brake rotors resurfaced (front or rear). ACTION: Use the ProCut PFM Series on-car brake lathe to perform brake rotor resurfacing and follow the tips listed in this bulletin. - The ProCut PFM Series brake lathe has been chosen as the approved tool for rotor resurfacing. - The ProCut PFM Series brake lathe can be ordered from TECH-MATE at 1-800-662-2001. - ProCut technical support or service can be obtained by calling 1-800-543-6618. NOTE: Brake rotors may need to be resurfaced during routine brake repair or for brake "judder" incidents. - Brake judder: A brake pedal pulsation and/or steering wheel shimmy when braking that occurs when there is too much thickness variation of the brake rotors (see NTB00-033). See this bulletin for further detail. |
|---|---|
| NTB00033E | 2021-05-10. Service bulletin. SERVICE INFORMATION - This bulletin is to assist you in responding to customer questions about brake operation, and provides diagnostic and repair information for each item listed, if any should occur. - Most brake incidents fall into the following categories: a. Brake Noise: A squeak, squeal, clunk, or groan that occurs when the brakes are applied or released. b. Brake Judder: A vibration that can be felt in the vehicle, steering wheel or brake pedal when the brakes are applied. c. Pedal Feel: The effort needed to operate the brakes is too high or too low. SERVICE PROCEDURE 1. Verify the condition by road testing the vehicle with the customer. 2. Determine the specific brake incident based on the description in the Service Information above. 3. Follow the appropriate repair procedure(s), listed on the following pages, for your specific incident. See this bulletin for further details. |
A bulletin is the manufacturer's note to its dealers. It is not part of this recall.