WenmarOpen by Wenmar Pro

NHTSA recall 26V051000

A recall listed here may apply to a vehicle of this year, make and model. Only the manufacturer can say whether it applies to one vehicle: check the VIN with the official lookups.

Campaign
Published byNHTSA (United States)
Campaign number26V051000
Manufacturer's number20D
ManufacturerChrysler (FCA US, LLC)
Reported2026-01-29
Owners notified2026-03-12
ComponentSUSPENSION:REAR:SPRINGS:COIL SPRINGS
Units potentially affected80620
Part numbers68375896AC
Remedy progress the manufacturer reported
ReportQuarterly report 2, for 2026 quarter 2
Filed with NHTSA2026-07-17
Vehicles in the campaign80620
Reported remedied24286 (30%)
Reported unreachable2659
Reported removed3762

These are the manufacturer's totals for the whole campaign at the end of 2026 quarter 2, as filed with NHTSA. They do not say whether one vehicle has been remedied: check the VIN with the official lookups. The reports are from data as of 2026-10-19.

What is wrong

Chrysler (FCA US, LLC) is recalling certain 2021-2023 Jeep Grand Cherokee L and 2022-2023 Jeep Grand Cherokee vehicles. The rear coil springs may be incorrectly installed and detach from the vehicle while driving.

What can happen

Rear coil springs that detach from the vehicle while driving increase the risk of a crash.

The remedy

Dealers will inspect and repair the rear coil spring assembly, as necessary, free of charge. Interim notification letters, notifying owners of the safety risk, were mailed February 12, 2026. Additional letters will be sent once the final remedy is available, anticipated in March 2026. Owners may contact FCA US, LLC customer service at 1-800-853-1403. FCA US, LLC's number for this recall is 20D. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on January 30, 2026. This recall replaces NHTSA recall number 23V413. Vehicles already repaired under the previous recall will need to have the new remedy completed.

Vehicles this campaign lists
2022 JEEP GRAND CHEROKEEBuilt from 2021-06-30.
2023 JEEP GRAND CHEROKEEBuilt to 2023-05-31.
2021 JEEP GRAND CHEROKEE LBuilt from 2020-12-05.
2022 JEEP GRAND CHEROKEE L
2023 JEEP GRAND CHEROKEE LBuilt to 2023-05-31.

A vehicle with no link is not in this site's catalog, which covers cars, multipurpose vehicles and trucks by model year. The campaign is from data as of 2026-10-19.

Investigated as RQ25005

This recall followed 1 NHTSA investigation. An investigation is NHTSA looking into a possible defect. It is not a finding that a defect exists, and it does not say that any one vehicle is affected.

NHTSA investigations that led to this recall
RQ25005Recall query, opened 2025-12-11. Recall 23V-413 Post Remedy Failures. SUSPENSION:REAR:SPRINGS:COIL SPRINGS.

From NHTSA's investigation file, as of 2026-10-19. The JSON has NHTSA's summary of each.

Bulletins for the same vehicles and component

Bulletins for the same vehicles and component
9100897Rev12026-09-17. Service bulletin. Qudra Lift Reman Compressor Excessive Repairs on Quadra Lift Reman Compressors Part Numbers: 68041137AF / R8572790AA / 68087233AA / 52124932AE / 52124934AE / 68064343AC Purpose The Star Parts Catalog has been updated to support component-level repair of the Quadra-Lift air suspension system. Replace only the component confirmed failed through diagnostics. Avoid replacing the complete assembly when an individual service component can correct the concern. Available Service Components Part Number Description R8572790AA Air Suspension Compressor 68087233AA Air Suspension Valve Block 52124932AE Front Air Suspension Hose Assembly 52124934AE Rear Air Suspension Hose Assembly 68064343AC Air Suspension Reservoir 68087240AA Temperature Sensor 68041137AF Compressor Assembly Diagnostic Decision Tree Customer Complaint: Service Air Suspension Message / Sagging / Unable to Adjust Ride Height / Compressor Running Continuously. Step 1: Retrieve and record all DTCs. C15D9 (Low Air Mass): Perform air mass test, complete system fill, leak-down test, and leak source identification before compressor replacement. C15A1 (Unable to Obtain Desired Ride Height): Verify ride height, perform leak-down test, inspect valve block, air lines, and air springs. C1562-98 (Over Temperature): Inspect for excessive compressor run time, leaks, low air mass, and restrictions before condemning the compressor. If a leak is found, repair the leak and verify operation before replacing the compressor. If no leak is found, perform compressor functional evaluation. If moisture is in the lines and valve block, then evacuate or replace lines. Only replace the compressor when a defect is verified (internal leak, failed solenoid, weak output, seized motor, failed functional test, or electrical failure). Service Component Selection Guide Verified Root Cause Recommended Repair Compressor Internal Failure Replace Compressor Valve Block Failure Replace Valve Block Air Line Leak Replace Air Line Air Spring Leak Replace Air Spring Temperature Sensor Failure Replace Temperature Sensor Technician Reminder Replace only the component confirmed failed through diagnostics. In many cases, compressor replacement is not required when the root cause is an air leak, valve block issue, airline concern, or sensor fault.
91008972026-09-10. Service bulletin. Qudra Lift Reman Compressor Excessive Repairs on Quadra Lift Reman Compressors Part Numbers: 68041137AF / R8572790AA / 68087233AA / 52124932AE / 52124934AE / 68064343AC Purpose The Star Parts Catalog has been updated to support component-level repair of the Quadra-Lift air suspension system. Replace only the component confirmed failed through diagnostics. Avoid replacing the complete assembly when an individual service component can correct the concern. Available Service Components Part Number Description R8572790AA Air Suspension Compressor 68087233AA Air Suspension Valve Block 52124932AE Front Air Suspension Hose Assembly 52124934AE Rear Air Suspension Hose Assembly 68064343AC Air Suspension Temperature Sensor 68041137AF Service Components Reference Diagnostic Decision Tree Customer Complaint: Service Air Suspension Message / Sagging / Unable to Adjust Ride Height / Compressor Running Continuously. Step 1: Retrieve and record all DTCs. C15D9 (Low Air Mass): Perform air mass test, complete system fill, leak-down test, and leak source identification before compressor replacement. C15A1 (Unable to Obtain Desired Ride Height): Verify ride height, perform leak-down test, inspect valve block, air lines, and air springs. C1562-98 (Over Temperature): Inspect for excessive compressor run time, leaks, low air mass, and restrictions before condemning the compressor. If a leak is found, repair the leak and verify operation before replacing the compressor. If no leak is found, perform compressor functional evaluation. If moisture is in the lines and valve block, then evacuate or replace lines. Only replace the compressor when a defect is verified (internal leak, failed solenoid, weak output, seized motor, failed functional test, or electrical failure). Service Component Selection Guide Verified Root Cause Recommended Repair Compressor Internal Failure Replace Compressor Valve Block Failure Replace Valve Block Air Line Leak Replace Air Line Air Spring Leak Replace Air Spring Temperature Sensor Failure Replace Temperature Sensor Technician Reminder Replace only the component confirmed failed through diagnostics. In many cases, compressor replacement is not required when the root cause is an air leak, valve block issue, airline concern, or sensor fault.
S2102000004 REV.D2026-07-02. Service bulletin. WL Front Control Arm Bushing - Handling Link Has Loose Rubber Appearance
9100811 Rev 42026-07-02. Service bulletin. Clunking when going over bumps, potholes, or turns. During diagnosis dealers may find rubber separating from the bushing on the handling link (SOL S2102000004 Rev C. for reference). This is normal and most likely is not attributed to the noise. Please follow normal diagnosis and ensure all tie-rod and ball joints are properly torqued and if worn, replace. If diagnosis leads to lower control arm replacement, the tension link(s) should be replaced first then test driven to ensure noise has disappeared before any handling link replacements.
S2503000001 REV.A2026-06-18. Service bulletin. Service 4WD Message, With Any Combination Of The Following Front Axle Disconnect (FAD) Diagnostic Trouble Codes
9100811Rev32026-06-03. Service bulletin. ***68375577A$ is not showing the correct verbiage please update and correct*** Clunking when going over bumps, potholes, or turns. During diagnosis dealers may find rubber separating from the bushing on the handling link (SOL S2102000004 Rev C. for reference). This is normal and most likely is not attributed to the noise. Please follow normal diagnosis and ensure all tie-rod and ball joints are properly torqued and if worn, replace. If diagnosis leads to lower control arm replacement, the tension link(s) should be replaced first then test driven to ensure noise has disappeared before any handling link replacements.
9100811 REV12026-05-28. Service bulletin. Clunking when going over bumps, potholes, or turns. During diagnosis dealers may find rubber separating from the bushing on the handling link (SOL S2102000004 Rev C. for reference). This is normal and most likely is not attributed to the noise. Please follow normal diagnosis and ensure all tie-rod and ball joints are properly torqued and if worn, replace. If diagnosis leads to lower control arm replacement, the tension link(s) should be replaced first then test driven to ensure noise has disappeared before any handling link replacements.
91008112026-05-20. Service bulletin. Clunking when going over bumps, potholes, or turns. During diagnosis dealers may find rubber separating from the bushing on the tension link. This is normal and most likely is not attributed to the noise. Please follow normal diagnosis and ensure all tie-rod and ball joints are properly torqued and if worn, replace. If diagnosis leads to lower control arm replacement, the tension link(s) should be replaced first then test driven to ensure noise has disappeared before any handling link replacements.
S2102000004 REV.C2026-04-29. Service bulletin. WL Front Control Arm Bushing - Handling Link Has Loose
9100446 Rev 52026-04-29. Service bulletin. BSR from the front suspension. Investigate the disconnecting stabilizer bar for a broken or cacked weld on the upper mount (anti rotation bracket). Instead of the replacing the whole stabilizer bar use Kit #PN#68730602AB. Refer to SOL #S2502000002 for additional information.

A bulletin is the manufacturer's note to its dealers. It is not part of this recall.

Check one vehicle officially