NHTSA recall 23V413000

A recall listed here may apply to a vehicle of this year, make and model. Only the manufacturer can say whether it applies to one vehicle: check the VIN with the official lookups.

Campaign
Published by	NHTSA (United States)
Campaign number	23V413000
Manufacturer's number	64A
Manufacturer	Chrysler (FCA US, LLC)
Reported	2023-06-08
Owners notified	2023-06-29
Component	SUSPENSION:REAR:SPRINGS:COIL SPRINGS
Units potentially affected	305282
Part numbers	Please see attached titled "FCA US LLC Recall Part Numbers-64A-WL Rear Coil Detachment-06082023.pdf"

Remedy progress the manufacturer reported
Report	Annual report 1, for 2025 quarter 2 to 2026 quarter 1
Filed with NHTSA	2026-04-28
Vehicles in the campaign	305282
Reported remedied	305282 (100%)
Reported unreachable	0
Reported removed	0

These are the manufacturer's totals for the whole campaign at the end of 2026 quarter 1, as filed with NHTSA. They do not say whether one vehicle has been remedied: check the VIN with the official lookups. The reports are from data as of 2026-10-19.

What is wrong

Chrysler (FCA US, LLC) is recalling certain 2022-2023 Jeep Grand Cherokee and 2021-2023 Jeep Grand Cherokee L vehicles. The rear coil springs may have been incorrectly installed and detach from the vehicle while driving.

What can happen

Rear coil springs that detach from the vehicle while driving increases the risk of a crash.

The remedy

Dealers will inspect and if necessary, repair the rear coil spring assemblies, free of charge. Owner notification letters were mailed June 29, 2023. Owners may contact FCA US, LLC customer service at 1-800-853-1403. FCA US, LLC's number for this recall is 64A. This recall is replaced by NHTSA recall 26V051. All vehicles will need to have the new recall remedy performed.

Notes

Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.nhtsa.gov.

Vehicles this campaign lists
2021 JEEP GRAND CHEROKEE
2023 JEEP GRAND CHEROKEE	Built to 2023-05-31.
2022 JEEP GRAND CHEROKEE 4XE	Listed as a series or trim of this model.

A vehicle with no link is not in this site's catalog, which covers cars, multipurpose vehicles and trucks by model year. The campaign is from data as of 2026-10-19.

Bulletins for the same vehicles and component

Bulletins for the same vehicles and component
9100897Rev1	2026-09-17. Service bulletin. Qudra Lift Reman Compressor Excessive Repairs on Quadra Lift Reman Compressors Part Numbers: 68041137AF / R8572790AA / 68087233AA / 52124932AE / 52124934AE / 68064343AC Purpose The Star Parts Catalog has been updated to support component-level repair of the Quadra-Lift air suspension system. Replace only the component confirmed failed through diagnostics. Avoid replacing the complete assembly when an individual service component can correct the concern. Available Service Components Part Number Description R8572790AA Air Suspension Compressor 68087233AA Air Suspension Valve Block 52124932AE Front Air Suspension Hose Assembly 52124934AE Rear Air Suspension Hose Assembly 68064343AC Air Suspension Reservoir 68087240AA Temperature Sensor 68041137AF Compressor Assembly Diagnostic Decision Tree Customer Complaint: Service Air Suspension Message / Sagging / Unable to Adjust Ride Height / Compressor Running Continuously. Step 1: Retrieve and record all DTCs. C15D9 (Low Air Mass): Perform air mass test, complete system fill, leak-down test, and leak source identification before compressor replacement. C15A1 (Unable to Obtain Desired Ride Height): Verify ride height, perform leak-down test, inspect valve block, air lines, and air springs. C1562-98 (Over Temperature): Inspect for excessive compressor run time, leaks, low air mass, and restrictions before condemning the compressor. If a leak is found, repair the leak and verify operation before replacing the compressor. If no leak is found, perform compressor functional evaluation. If moisture is in the lines and valve block, then evacuate or replace lines. Only replace the compressor when a defect is verified (internal leak, failed solenoid, weak output, seized motor, failed functional test, or electrical failure). Service Component Selection Guide Verified Root Cause Recommended Repair Compressor Internal Failure Replace Compressor Valve Block Failure Replace Valve Block Air Line Leak Replace Air Line Air Spring Leak Replace Air Spring Temperature Sensor Failure Replace Temperature Sensor Technician Reminder Replace only the component confirmed failed through diagnostics. In many cases, compressor replacement is not required when the root cause is an air leak, valve block issue, airline concern, or sensor fault.
9100897	2026-09-10. Service bulletin. Qudra Lift Reman Compressor Excessive Repairs on Quadra Lift Reman Compressors Part Numbers: 68041137AF / R8572790AA / 68087233AA / 52124932AE / 52124934AE / 68064343AC Purpose The Star Parts Catalog has been updated to support component-level repair of the Quadra-Lift air suspension system. Replace only the component confirmed failed through diagnostics. Avoid replacing the complete assembly when an individual service component can correct the concern. Available Service Components Part Number Description R8572790AA Air Suspension Compressor 68087233AA Air Suspension Valve Block 52124932AE Front Air Suspension Hose Assembly 52124934AE Rear Air Suspension Hose Assembly 68064343AC Air Suspension Temperature Sensor 68041137AF Service Components Reference Diagnostic Decision Tree Customer Complaint: Service Air Suspension Message / Sagging / Unable to Adjust Ride Height / Compressor Running Continuously. Step 1: Retrieve and record all DTCs. C15D9 (Low Air Mass): Perform air mass test, complete system fill, leak-down test, and leak source identification before compressor replacement. C15A1 (Unable to Obtain Desired Ride Height): Verify ride height, perform leak-down test, inspect valve block, air lines, and air springs. C1562-98 (Over Temperature): Inspect for excessive compressor run time, leaks, low air mass, and restrictions before condemning the compressor. If a leak is found, repair the leak and verify operation before replacing the compressor. If no leak is found, perform compressor functional evaluation. If moisture is in the lines and valve block, then evacuate or replace lines. Only replace the compressor when a defect is verified (internal leak, failed solenoid, weak output, seized motor, failed functional test, or electrical failure). Service Component Selection Guide Verified Root Cause Recommended Repair Compressor Internal Failure Replace Compressor Valve Block Failure Replace Valve Block Air Line Leak Replace Air Line Air Spring Leak Replace Air Spring Temperature Sensor Failure Replace Temperature Sensor Technician Reminder Replace only the component confirmed failed through diagnostics. In many cases, compressor replacement is not required when the root cause is an air leak, valve block issue, airline concern, or sensor fault.
S2102000004 REV.D	2026-07-02. Service bulletin. WL Front Control Arm Bushing - Handling Link Has Loose Rubber Appearance
9100811 Rev 4	2026-07-02. Service bulletin. Clunking when going over bumps, potholes, or turns. During diagnosis dealers may find rubber separating from the bushing on the handling link (SOL S2102000004 Rev C. for reference). This is normal and most likely is not attributed to the noise. Please follow normal diagnosis and ensure all tie-rod and ball joints are properly torqued and if worn, replace. If diagnosis leads to lower control arm replacement, the tension link(s) should be replaced first then test driven to ensure noise has disappeared before any handling link replacements.
S2503000001 REV.A	2026-06-18. Service bulletin. Service 4WD Message, With Any Combination Of The Following Front Axle Disconnect (FAD) Diagnostic Trouble Codes
9100811Rev3	2026-06-03. Service bulletin. *68375577A$ is not showing the correct verbiage please update and correct* Clunking when going over bumps, potholes, or turns. During diagnosis dealers may find rubber separating from the bushing on the handling link (SOL S2102000004 Rev C. for reference). This is normal and most likely is not attributed to the noise. Please follow normal diagnosis and ensure all tie-rod and ball joints are properly torqued and if worn, replace. If diagnosis leads to lower control arm replacement, the tension link(s) should be replaced first then test driven to ensure noise has disappeared before any handling link replacements.
9100811 REV1	2026-05-28. Service bulletin. Clunking when going over bumps, potholes, or turns. During diagnosis dealers may find rubber separating from the bushing on the handling link (SOL S2102000004 Rev C. for reference). This is normal and most likely is not attributed to the noise. Please follow normal diagnosis and ensure all tie-rod and ball joints are properly torqued and if worn, replace. If diagnosis leads to lower control arm replacement, the tension link(s) should be replaced first then test driven to ensure noise has disappeared before any handling link replacements.
9100811	2026-05-20. Service bulletin. Clunking when going over bumps, potholes, or turns. During diagnosis dealers may find rubber separating from the bushing on the tension link. This is normal and most likely is not attributed to the noise. Please follow normal diagnosis and ensure all tie-rod and ball joints are properly torqued and if worn, replace. If diagnosis leads to lower control arm replacement, the tension link(s) should be replaced first then test driven to ensure noise has disappeared before any handling link replacements.
S2102000004 REV.C	2026-04-29. Service bulletin. WL Front Control Arm Bushing - Handling Link Has Loose
9100446 Rev 5	2026-04-29. Service bulletin. BSR from the front suspension. Investigate the disconnecting stabilizer bar for a broken or cacked weld on the upper mount (anti rotation bracket). Instead of the replacing the whole stabilizer bar use Kit #PN#68730602AB. Refer to SOL #S2502000002 for additional information.

A bulletin is the manufacturer's note to its dealers. It is not part of this recall.