NHTSA recall 13V464000
A recall listed here may apply to a vehicle of this year, make and model. Only the manufacturer can say whether it applies to one vehicle: check the VIN with the official lookups.
| Published by | NHTSA (United States) |
|---|---|
| Campaign number | 13V464000 |
| Manufacturer's number | 13296 |
| Manufacturer | General Motors LLC |
| Reported | 2013-09-26 |
| Owners notified | 2013-11-07 |
| Component | FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY:MOUNTING |
| Units potentially affected | 1558 |
| Report | Quarterly report 6, for 2015 quarter 1 |
|---|---|
| Filed with NHTSA | 2015-04-15 |
| Vehicles in the campaign | 1558 |
| Reported remedied | 1425 (91%) |
| Reported unreachable | 11 |
| Reported removed | 0 |
These are the manufacturer's totals for the whole campaign at the end of 2015 quarter 1, as filed with NHTSA. They do not say whether one vehicle has been remedied: check the VIN with the official lookups. The reports are from data as of 2026-10-19.
What is wrong
General Motors (GM) is recalling certain model year 2013 and 2014 Chevrolet Sonic vehicles manufactured August 2, 2013, through August 12, 2013. Due to insufficient welds, the front fuel tank strap bracket may separate from the vehicle.
What can happen
If the front fuel tank strap bracket separates, the increased load may lead to the failure of the other tank support. As a result, the fuel tank may come loose from the vehicle causing a fuel leak. A fuel leak, in the presence of an ignition source, may result in a fire.
The remedy
GM will notify owners, and dealers will inspect the front fuel tank strap bracket, and repair it as necessary, free of charge. The recall began on November 7, 2013. Owners may contact GM at 1-800-521-7300. GM's recall campaign number is 13296.
Notes
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.
| 2013 CHEVROLET SONIC | Built 2013-08-02 to 2013-08-09. |
|---|---|
| 2014 CHEVROLET SONIC | Built 2013-08-12 to 2013-08-12. |
A vehicle with no link is not in this site's catalog, which covers cars, multipurpose vehicles and trucks by model year. The campaign is from data as of 2026-10-19.
Bulletins for the same vehicles and component
| PIT4943D | 2017-08-15. Service bulletin. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay. |
|---|---|
| SB-13296A-A | 2016-03-16. Service bulletin. SUMMARY TO BE PROVIDED ON A FUTURE DATE. |
| SB-13296 | 2016-03-16. Service bulletin. SUMMARY TO BE PROVIDED ON A FUTURE DATE. |
| SB-13296-A | 2016-03-16. Service bulletin. SUMMARY TO BE PROVIDED ON A FUTURE DATE. |
A bulletin is the manufacturer's note to its dealers. It is not part of this recall.