NHTSA recall 12V289000
A recall listed here may apply to a vehicle of this year, make and model. Only the manufacturer can say whether it applies to one vehicle: check the VIN with the official lookups.
| Published by | NHTSA (United States) |
|---|---|
| Campaign number | 12V289000 |
| Manufacturer's number | 12133 |
| Manufacturer | GENERAL MOTORS LLC |
| Reported | 2012-06-22 |
| Owners notified | 2012-07-09 |
| Component | FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY:MOUNTING |
| Units potentially affected | 53239 |
What is wrong
GENERAL MOTORS (GM) IS RECALLING CERTAIN MODEL YEAR 2011 AND 2012 CHEVROLET CRUZE VEHICLES MANUFACTURED FROM OCTOBER 2, 2009, THROUGH MAY 14, 2012. ATTACHMENT WELDS FOR THE FUEL TANK STRAP SECONDARY BRACKETS MAY HAVE BEEN OMITTED.
What can happen
THE FUEL TANK COULD COME LOOSE IN A CRASH, POSSIBLY ALLOWING FUEL TO LEAK FROM THE TANK. A FUEL LEAK IN THE PRESENCE OF AN IGNITION SOURCE COULD RESULT IN A FIRE.
The remedy
GM WILL NOTIFY OWNERS, AND DEALERS WILL INSPECT THE VEHICLE FOR MISSING WELDS. IF THE VEHICLE IS MISSING WELDS, DEALERS WILL SECURE THE BRACKET ATTACHMENTS WITH FASTENERS. REPAIRS WILL BE PERFORMED FREE OF CHARGE. THE SAFETY RECALL BEGAN ON JULY 9, 2012. OWNERS MAY CONTACT THE CHEVROLET OWNER CENTER AT 1-866-694-6546.
Notes
GM’S CAMPAIGN NUMBER IS 12133.OWNERS MAY ALSO CONTACT THE NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION'S VEHICLE SAFETY HOTLINE AT 1-888-327-4236 (TTY 1-800-424-9153), OR GO TO <A HREF=HTTP://WWW.SAFERCAR.GOV>HTTP://WWW.SAFERCAR.GOV</A> .
| 2011 CHEVROLET CRUZE | Built 2009-10-02 to 2011-06-20. |
|---|---|
| 2012 CHEVROLET CRUZE | Built 2011-06-23 to 2012-05-14. |
A vehicle with no link is not in this site's catalog, which covers cars, multipurpose vehicles and trucks by model year. The campaign is from data as of 2026-10-19.
Bulletins for the same vehicles and component
| PIT4943D | 2017-08-15. Service bulletin. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay. |
|---|---|
| PI-0526A | 2011-10-03. Service bulletin. BUICK/CHEVROLET/GMC: INDICATOR LAMP IS MALFUNCTIONING INTERMITTENTLY. *PE |
A bulletin is the manufacturer's note to its dealers. It is not part of this recall.