NHTSA recall 03V307000
A recall listed here may apply to a vehicle of this year, make and model. Only the manufacturer can say whether it applies to one vehicle: check the VIN with the official lookups.
| Published by | NHTSA (United States) |
|---|---|
| Campaign number | 03V307000 |
| Manufacturer's number | RU301 |
| Manufacturer | NISSAN NORTH AMERICA, INC. |
| Reported | 2003-08-22 |
| Owners notified | 2003-09-15 |
| Component | WHEELS |
| Units potentially affected | 31700 |
What is wrong
2000 NISSAN XTERRA VEHICLES MANUFACTURED BETWEEN OCTOBER 15, 1999, AND FEBRUARY 29, 2000. THE ALLOY WHEELS USED ON THESE VEHICLES MAY NOT HAVE BEEN PROPERLY MANUFACTURED AND COULD DEVELOP CRACKS IN THE WHEEL SPOKES.
What can happen
IF A SUFFICIENT NUMBER OF SPOKE CRACKS DEVELOP, THE WHEEL COULD FAIL AND SEPARATE FROM THE MOUNTING HUB, POSSIBLY RESULTING IN A VEHICLE CRASH WITHOUT PRIOR WARNING.
The remedy
NISSAN WILL NOTIFY ITS CUSTOMERS AND REPLACE THE FOUR ALLOY WHEELS WITH XTERRA SE MODEL BRIGHT ALLOY WHEELS FREE OF CHARGE. THE SPARE TIRE STEEL WHEEL IS NOT AFFECTED. OWNER NOTIFICATION BEGAN ON SEPTEMBER 15, 2003. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT NISSAN AT 1-800-647-7261. INFORMATION CAN ALSO BE OBTAINED THROUGH NISSAN'S WEB SITE AT WWW.NISSANUSA.COM.
Notes
ALSO, CUSTOMERS CAN CONTACT THE NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION'S AUTO SAFETY HOTLINE AT 1-888-DASH-2-DOT (1-888-327-4236).
| 2000 NISSAN XTERRA | Built 1999-10-15 to 2000-02-29. |
|---|
A vehicle with no link is not in this site's catalog, which covers cars, multipurpose vehicles and trucks by model year. The campaign is from data as of 2026-10-19.
Bulletins for the same vehicles and component
| NTB10-126C | 2023-03-07. Service bulletin. WHEEL BEARING COLLISION DAMAGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. |
|---|---|
| NTB92123D | 2021-05-10. Service bulletin. Nissan Original Equipment or Genuine Accessory Alloy wheels, along with their finish coating (clear, chrome, titanium, etc.), are specifically developed to achieve Nissan design and performance standards. These Original Equipment or Genuine Accessory wheels are subjected to testing to ensure they meet Nissan's standards. Nissan Original Equipment Alloy or Genuine Accessory wheels subjected to aftermarket chroming may no longer continue to meet these standards and may be seriously damaged. Therefore, Nissan most strongly discourages, and recommends that these wheels NEVER be subjected to, aftermarket chroming. See this bulletinfor further detail. |
| NTB04094A | 2021-05-10. Service bulletin. If YOU CONFIRM: A vehicle needs to have the brake rotors resurfaced (front or rear). ACTION: Use the ProCut PFM Series on-car brake lathe to perform brake rotor resurfacing and follow the tips listed in this bulletin. - The ProCut PFM Series brake lathe has been chosen as the approved tool for rotor resurfacing. - The ProCut PFM Series brake lathe can be ordered from TECH-MATE at 1-800-662-2001. - ProCut technical support or service can be obtained by calling 1-800-543-6618. NOTE: Brake rotors may need to be resurfaced during routine brake repair or for brake "judder" incidents. - Brake judder: A brake pedal pulsation and/or steering wheel shimmy when braking that occurs when there is too much thickness variation of the brake rotors (see NTB00-033). See this bulletin for further detail. |
| NTB00033E | 2021-05-10. Service bulletin. SERVICE INFORMATION - This bulletin is to assist you in responding to customer questions about brake operation, and provides diagnostic and repair information for each item listed, if any should occur. - Most brake incidents fall into the following categories: a. Brake Noise: A squeak, squeal, clunk, or groan that occurs when the brakes are applied or released. b. Brake Judder: A vibration that can be felt in the vehicle, steering wheel or brake pedal when the brakes are applied. c. Pedal Feel: The effort needed to operate the brakes is too high or too low. SERVICE PROCEDURE 1. Verify the condition by road testing the vehicle with the customer. 2. Determine the specific brake incident based on the description in the Service Information above. 3. Follow the appropriate repair procedure(s), listed on the following pages, for your specific incident. See this bulletin for further details. |
A bulletin is the manufacturer's note to its dealers. It is not part of this recall.