NHTSA recall 02V316000
A recall listed here may apply to a vehicle of this year, make and model. Only the manufacturer can say whether it applies to one vehicle: check the VIN with the official lookups.
| Published by | NHTSA (United States) |
|---|---|
| Campaign number | 02V316000 |
| Manufacturer's number | R2021 |
| Manufacturer | NISSAN NORTH AMERICA, INC. |
| Reported | 2002-11-26 |
| Owners notified | 2003-01-13 |
| Component | WHEELS:RIM |
| Units potentially affected | 6500 |
What is wrong
ON CERTAIN SPORT UTILITY VEHICLES EQUIPPED WITH A V6 ENGINE, AN INCORRECT SIZE WHEEL RIM FOR THE SPARE TIRE WAS PROVIDED IN THESE VEHICLES. THE WHEEL RIM DOES NOT FIT PROPERLY AS A REPLACEMENT FOR A FRONT WHEEL.
What can happen
WHEN INSTALLED ON THE FRONT OF THE VEHICLE, THE WHEEL RIM WILL CONTACT THE BRAKE CALIPER CAUSING A LOUD RUBBING NOISE AND COULD RESULT IN WEAR ON THE CALIPER AND/OR WHEEL RIM IF DRIVING CONTINUES. CONTINUED USAGE OF THE SPARE TIRE WHEEL AT THE FRONT LOCATION CAN ALSO RESULT IN LOOSENING OF THE LUG NUTS AND DETERIORATION IN BRAKING PERFORMANCE. THIS COULD EVENTUALLY CAUSE THE WHEEL ASSEMBLY TO SEPARATE FORM THE VEHICLE AND RESULT IN LOSS OF CONTROL AND A CRASH.
The remedy
DEALERS WILL REPLACE THE SPARE TIRE WHEEL RIM WITH A NEW ONE, AND REMOUNT THE SPARE TIRE ON IT. OWNER NOTIFICATION BEGAN JANUARY 13, 2003. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT NISSAN AT 1-800-647-7261.
Notes
ALSO CONTACT THE NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION'S AUTO SAFETY HOTLINE AT 1-888-DASH-2-DOT (1-888-327-4236).
| 2003 NISSAN FRONTIER | Built 2002-07-17 to 2002-11-07. |
|---|
A vehicle with no link is not in this site's catalog, which covers cars, multipurpose vehicles and trucks by model year. The campaign is from data as of 2026-10-19.
Bulletins for the same vehicles and component
| NTB10-126C | 2023-03-07. Service bulletin. WHEEL BEARING COLLISION DAMAGE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. |
|---|---|
| NTB92123D | 2021-05-10. Service bulletin. Nissan Original Equipment or Genuine Accessory Alloy wheels, along with their finish coating (clear, chrome, titanium, etc.), are specifically developed to achieve Nissan design and performance standards. These Original Equipment or Genuine Accessory wheels are subjected to testing to ensure they meet Nissan's standards. Nissan Original Equipment Alloy or Genuine Accessory wheels subjected to aftermarket chroming may no longer continue to meet these standards and may be seriously damaged. Therefore, Nissan most strongly discourages, and recommends that these wheels NEVER be subjected to, aftermarket chroming. See this bulletinfor further detail. |
| NTB04094A | 2021-05-10. Service bulletin. If YOU CONFIRM: A vehicle needs to have the brake rotors resurfaced (front or rear). ACTION: Use the ProCut PFM Series on-car brake lathe to perform brake rotor resurfacing and follow the tips listed in this bulletin. - The ProCut PFM Series brake lathe has been chosen as the approved tool for rotor resurfacing. - The ProCut PFM Series brake lathe can be ordered from TECH-MATE at 1-800-662-2001. - ProCut technical support or service can be obtained by calling 1-800-543-6618. NOTE: Brake rotors may need to be resurfaced during routine brake repair or for brake "judder" incidents. - Brake judder: A brake pedal pulsation and/or steering wheel shimmy when braking that occurs when there is too much thickness variation of the brake rotors (see NTB00-033). See this bulletin for further detail. |
| NTB00033E | 2021-05-10. Service bulletin. SERVICE INFORMATION - This bulletin is to assist you in responding to customer questions about brake operation, and provides diagnostic and repair information for each item listed, if any should occur. - Most brake incidents fall into the following categories: a. Brake Noise: A squeak, squeal, clunk, or groan that occurs when the brakes are applied or released. b. Brake Judder: A vibration that can be felt in the vehicle, steering wheel or brake pedal when the brakes are applied. c. Pedal Feel: The effort needed to operate the brakes is too high or too low. SERVICE PROCEDURE 1. Verify the condition by road testing the vehicle with the customer. 2. Determine the specific brake incident based on the description in the Service Information above. 3. Follow the appropriate repair procedure(s), listed on the following pages, for your specific incident. See this bulletin for further details. |
A bulletin is the manufacturer's note to its dealers. It is not part of this recall.