NHTSA recall 00V160000
A recall listed here may apply to a vehicle of this year, make and model. Only the manufacturer can say whether it applies to one vehicle: check the VIN with the official lookups.
| Published by | NHTSA (United States) |
|---|---|
| Campaign number | 00V160000 |
| Manufacturer's number | 00056 |
| Manufacturer | GENERAL MOTORS CORP. |
| Reported | 2000-06-16 |
| Owners notified | 2000-06-21 |
| Component | FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY:FILLER PIPE AND CAP |
| Units potentially affected | 248 |
What is wrong
VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE CLAMP THAT SECURES THE FLEXIBLE FUEL FILL HOSE TO THE METAL FILL TUBE MAY BE LOOSE AND COULD SEPARATE.
What can happen
THIS COULD CAUSE FUEL LEAKAGE EXCEEDING THE PERMISSIBLE AMOUNT.
The remedy
DEALERS WILL INSPECT THE FUEL HOSE FILL NECK CLAMP AND, IF NECESSARY, REPOSITION AND TIGHTEN THE CLAMP.
Notes
OWNER NOTIFICATION BEGAN JUNE 21, 2000. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT CHEVROLET AT 1-800-222-1020 OR BUICK AT 1-800-521-7300.ALSO CONTACT THE NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION'S AUTO SAFETY HOTLINE AT 1-888-DASH-2-DOT (1-888-327-4236).
| 2000 BUICK CENTURY | Built 2000-05-01 to 2000-05-31. |
|---|---|
| 2000 BUICK REGAL | Built 2000-05-01 to 2000-05-31. |
| 2000 CHEVROLET LUMINA | Built 2000-05-01 to 2000-05-31. |
A vehicle with no link is not in this site's catalog, which covers cars, multipurpose vehicles and trucks by model year. The campaign is from data as of 2026-10-19.
Bulletins for the same vehicles and component
| PIT4943D | 2017-08-15. Service bulletin. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay. |
|---|---|
| 020101 | 2001-04-06. Service bulletin. INFORMATION ON VEHICLES EXHIBITING AN OPR VALVE CAUSING DIAGNOSTIC TROUBLE CODE P0442, OR CAUSING A LEAK, AIR WILL BE HEARD EXITING THE RUBBER DUMP HOSE LOCATED ON THE LEFT SIDE OF THE FUEL TANK. *TT |
A bulletin is the manufacturer's note to its dealers. It is not part of this recall.