Service bulletins for the 2017 Toyota 86
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
101 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
| T-SB-0038-16 | 2018-06-11. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT. TSB: 2017 model year vehicles are equipped with driver?s side floor mat retaining clips to secure the floor mat in the correct position. In addition, some models may utilize retaining clips for passenger side and rear seat floor mats as well. Follow the appropriate Installation Procedure to attach the driver?s side, and if applicable, the passenger?s side and rear seat floor mats to the vehicle carpet using the floor mat retaining clips during Pre-Delivery Service (PDS). |
|---|---|
| T-SB-0037-16 | 2018-06-11. Service bulletin. EQUIPMENT; EQUIPMENT ADAPTIVE/MOBILITY. TSB: Some 2017 model year vehicles are equipped with a Smart Key system, which allows the customer to enter and start the vehicle without using a mechanical key. To ensure the system is operating properly, the Smart Key functions (Smart Entry and Smart Start) should be inspected using the following procedure during Pre-Delivery Service (PDS). Note: Check ALL of the Smart Keys using this procedure. |
| T-SB-0076-16 | 2018-04-23. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM; STRUCTURE. TSB: 2017 86 Pre-Delivery Service. Pre-Delivery Service (PDS) is a critical step in satisfying the dealership?s new car customers. Customer feedback indicates the following areas deserve special attention when performing PDS: *Careful inspection for paint chips/scratches and body dents/dings. Proper operation of electrical accessories (including interior light, clock, and radio reset). *Interior cleanliness. *Proper function of mechanical systems. |
| T-SB-0075-16 | 2018-04-23. Service bulletin. EQUIPMENT. TSB: 2017 Pre-Delivery Service Check Sheet |
| TSB-0039-16 Rev1 | 2018-04-23. Service bulletin. ELECTRICAL SYSTEM:12V/24V/48V BATTERY. TSB: A battery in a stored vehicle is subject to conditions that can reduce its performance and life. These conditions include storage period, temperature, parasitic drain, and battery load. Because of these factors, battery inspection and maintenance are required in order to ensure proper operation and optimal battery life. |
| T-SB-0229-12_Rev | 2018-04-23. Service bulletin. ELECTRICAL SYSTEM. TSB: REVISION NOTICE November 22, 2017 Rev1: ? Applicability has been updated to include 2014 ? 2018 model year vehicles. Any previous printed versions of this bulletin should be discarded. In the event that a Toyota vehicle becomes submerged in water, many components may be physically damaged. Electrical and electronic components, including wiring harnesses, are particularly susceptible to corrosion and subsequent malfunction. Although any flooding can be damaging, salt water flooding elevates the potential for abnormal conditions and may increase risks due to its highly corrosive and conductive nature. Salt residue also continues to corrode and remain conductive even after a vehicle dries. This bulletin is intended to assist with safe handling and inspection of flood damaged vehicles and to provide basic guidance on likely needed repairs. |
| T-TT-0424-16 | 2018-04-02. Service bulletin. WHEELS:LUGS/NUTS/BOLTS/STUDS. TT: Front Brake Vibration Key Points: * Issue can occur at any time if improper torque is applied on lug nuts * Over time, even one lug nut over or under torqued, can cause a vibration issue * When lug nuts are over torqued, this causes the rotor to have a runout out condition which can lead to brake vibration concerns * Brake vibration issues can occur at parking lot to highway speeds * Brake vibration issues can occur at light to moderate braking * Tightening lug nuts in a star pattern method during the torqueing process will assure that even/equal pressure is applied across the rotor hub surface * Torque sticks/wrenches should be used to apply accurate torque values when tightening * Do Not use impact guns/ratchets to completely run lug nuts up to the wheel surface |
| T-SB-0218-17_Rev | 2018-04-02. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; AIR BAGS. TSB: REVISION NOTICE July 20, 2017 Rev1: Applicability has been updated to exclude 2007 ? 2017 model year Avanza vehicles. Some hazardous material treatment and handling regulations at the state and local level define the pre-disposal deployment of airbag and pre-tensioner assemblies as hazardous material treatment. Hazardous material treatment may require special training, certification or licensing in certain areas. TMS recommends that dealership personnel carefully review and follow ALL local and state regulations, and where necessary, contract with Environmental Protection Agency (EPA) Licensed Hazardous Waste Transportation and Disposal facilities. |
| Toyota Safety Re | 2018-04-02. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; EQUIPMENT. Update on Technician Certification Requirements |
| T-SB-0044-16_Rev | 2018-04-02. Service bulletin. STRUCTURE:BODY. TSB: REVISION NOTICE March 07, 2017 Rev1: ? Applicability has been updated to include 2017 model year Toyota vehicles. On some vehicles, when Rapgard? is removed the paint may have a stained appearance. These stains appear to be under the clear coat (repainting this area is NOT necessary). The stain patterns are usually under wrinkles in the Rapgard?. These wrinkles sometimes trap water and cause the paint to stain from the trapped moisture, especially on horizontal surfaces, such as the hood, roof, and trunk. Stains can be removed by heating the stained surface to remove the trapped moisture. |
| T-TT-0482-18 | 2018-04-02. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). TSB: Some vehicles may display a 22-digit request code when attempting to perform a navigation map update. |
| T-SB-0187-12_Rev | 2018-04-02. Service bulletin. TIRES. TSB: REVISION NOTICE February 12, 2018 Rev2: ? Applicability has been updated to include 2015 ? 2018 model year vehicles. January 23, 2014 Rev1: ? Applicability has been updated to include 2013 ? 2014 model year vehicles. Any previous printed versions of this bulletin should be discarded. Toyota vehicles are equipped with either conventional or run-flat tires. Sometimes punctures may occur as a result of contact with road debris or other hazards. If a puncture occurs, it may be possible to repair the tire and return it to service. With a conventional tire it is not possible to drive for an extended amount of time with the tire at low pressures as damage to the tire may occur. With run-flat tires, due to reinforced sidewalls, it is possible to drive for up to 100 miles at speeds less than 55 mph with little or no damage to the tire. The U.S. Tire Manufacturers Association (UTSMA) provides guidelines and recommendations for tire repair and replacement. It also provides information related to: ? Basic tire information ? Tire maintenance and safety ? Driver education, tire safety curriculum. |
| T-SB-0304-17_Rev | 2018-04-02. Service bulletin. EQUIPMENT. TSB: SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin Nos. PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, and T-SB-0144-08. Service Bulletin Nos. PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, and T-SB-0144-08 are obsolete and any printed versions should be discarded. Be sure to review the entire content of this bulletin before proceeding. REVISION NOTICE January 11, 2018 ? The Supersession Notice has been updated. Any previous printed versions of this bulletin should be discarded. Vehicle replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) may be available from Toyota, provided the request meets one of the criteria listed in this Service Bulletin. |
| T-TT-0475-18 | 2018-04-02. Service bulletin. FUEL SYSTEM, GASOLINE. TT: In the event that injector seal repair is required on vehicles equipped with a direct injection fuel system, a Special Service Tool Set is required to properly install the seal onto the injector. As new vehicle configurations have been released, several injector seal tool sets have been distributed to accommodate these new vehicles. There are a total of three injector seal tool sets for Toyota models, located in the appropriate SST cabinets. Each kit contains multiple pieces as shown in the diagram below. The individual pieces must remain together to ensure these tools are used correctly. Refer to the repair manual for the tool information to ensure the correct tool is used for the desired application. |
| T-TT-0482-18 | 2018-03-12. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); ELECTRICAL SYSTEM. TSB: Some vehicles may display a 22-digit request code when attempting to perform a navigation map update. |
| T-SB-0187-12_Rev | 2018-03-12. Service bulletin. TIRES. TSB: REVISION NOTICE February 12, 2018 Rev2: ? Applicability has been updated to include 2015 ? 2018 model year vehicles. January 23, 2014 Rev1: ? Applicability has been updated to include 2013 ? 2014 model year vehicles. Any previous printed versions of this bulletin should be discarded. Toyota vehicles are equipped with either conventional or run-flat tires. Sometimes punctures may occur as a result of contact with road debris or other hazards. If a puncture occurs, it may be possible to repair the tire and return it to service. With a conventional tire it is not possible to drive for an extended amount of time with the tire at low pressures as damage to the tire may occur. With run-flat tires, due to reinforced sidewalls, it is possible to drive for up to 100 miles at speeds less than 55 mph with little or no damage to the tire. The U.S. Tire Manufacturers Association (UTSMA) provides guidelines and recommendations for tire repair and replacement. It also provides information related to: ? Basic tire information ? Tire maintenance and safety ? Driver education, tire safety curriculum. |
| T-SB-0134-16_Rev | 2017-11-14. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. TSB: REVISION NOTICE October 30, 2017 Rev1: * Applicability has been updated to include 2018 model year vehicles. SUPERSESSION NOTICE The information contained in this bulletin supersedes SB No. T-SB-0012-13. Flash reprogramming allows the Electronic Control Unit (ECU) software to be updated without replacing the ECU. Flash calibration updates for specific vehicle models/ECUs are released as field-fix procedures described in individual Service Bulletins. This bulletin details the Techstream ECU flash reprogramming process and outlines use of the Technical Information System (TIS) and the Calibration Update Wizard (CUW). Flash calibration updates can only be applied to the vehicle/ECU combination for which they are intended. ECUs have internal security that will not allow them to be programmed with another ECU's information. |
| T-SB-0304-17 | 2017-11-14. Service bulletin. STRUCTURE:BODY:DOOR. TSB: Vehicle replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) may be available from Toyota, provided the request meets one of the criteria listed in this Service Bulletin. |
| T-SB-0042-16 | 2017-06-15. Service bulletin. TIRES. DURING THE MANUFACTURING PROCESS, TIRES ARE MOUNTED ON THE VEHICLE AS MATCHED SETS TO HELP REDUCE CONDITIONS SUCH AS PULLING OR DRIFTING. IF THE WHEELS ARE REPLACED OR REFINISHED BEFORE VEHICLE DELIVERY, IT IS IMPORTANT THAT THE TIRES REMAIN ON THE VEHICLE IN THE SAME LOCATION AND IN THE SAME DIRECTION OF ROTATION. |
| T-SB-0039-16 REV | 2017-06-12. Service bulletin. ELECTRICAL SYSTEM:12V/24V/48V BATTERY. TSB: A BATTERY IN A STORED VEHICLE IS SUBJECT TO CONDITIONS THAT CAN REDUCE ITS PERFORMANCE AND LIFE. THESE CONDITIONS INCLUDE STORAGE PERIOD, TEMPERATURE, PARASITIC DRAIN, AND BATTERY LOAD. BECAUSE OF THESE FACTORS, BATTERY INSPECTION AND MAINTENANCE ARE REQUIRED IN ORDER TO ENSURE PROPER OPERATION AND OPTIMAL BATTERY LIFE. |
| T-SB-0045-16 | 2017-04-04. Service bulletin. EQUIPMENT; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. TSB: LONG-TERM OR OFF-SITE STORAGE REQUIRES SPECIAL CARE TO KEEP VEHICLES FACTORY FRESH AND READY FOR DELIVERY. THE FOLLOWING GUIDELINES SHOULD BE PERFORMED TO MINIMIZE VEHICLE COMPONENT/PART DEGRADATION DUE TO EXTENDED VEHICLE STORAGE CONDITIONS. LONG-TERM STORAGE CAN AFFECT A VEHICLE’S SYSTEMS AND COMPONENTS. ANY PROBLEMS THAT ARE FOUND SHOULD BE CORRECTED IMMEDIATELY. |
| T-SB-0039-16 | 2017-02-27. Service bulletin. ELECTRICAL SYSTEM:12V/24V/48V BATTERY. TSB: A BATTERY IN A STORED VEHICLE IS SUBJECT TO CONDITIONS THAT CAN REDUCE ITS PERFORMANCE AND LIFE. THESE CONDITIONS INCLUDE STORAGE PERIOD, TEMPERATURE, PARASITIC DRAIN, AND BATTERY LOAD. BECAUSE OF THESE FACTORS, BATTERY INSPECTION AND MAINTENANCE ARE REQUIRED IN ORDER TO ENSURE PROPER OPERATION AND OPTIMAL BATTERY LIFE. AS A MATTER OF POLICY, TOYOTA DOES NOT PROVIDE BATTERY WARRANTY COVERAGE FOR DISCHARGED AND/OR FAILED BATTERIES DUE TO LACK OF MAINTENANCE. IT IS THE DEALER’S RESPONSIBILITY TO MAINTAIN THE SPECIFIED STATE OF CHARGE (SOC) OF THE VEHICLE’S BATTERY WHILE IN STOCK AND ASSURE PROPER STATE OF CHARGE (SOC) AT DELIVERY. TO ELIMINATE CUSTOMER SERVICE CONCERNS DUE TO AN UNDERCHARGED BATTERY DURING THE FIRST FEW WEEKS OF OWNERSHIP, ALL DEALERS SHOULD CHECK BATTERY STATE OF CHARGE (SOC) AND RECHARGE, IF NECESSARY, WITHIN 48 HOURS OF DELIVERY TO CUSTOMERS. |
| T-SB-0038-16 | 2017-02-27. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY. TSB: 2017 MODEL YEAR VEHICLES ARE EQUIPPED WITH DRIVER’S SIDE FLOOR MAT RETAINING CLIPS TO SECURE THE FLOOR MAT IN THE CORRECT POSITION. IN ADDITION, SOME MODELS MAY UTILIZE RETAINING CLIPS FOR PASSENGER SIDE AND REAR SEAT FLOOR MATS AS WELL. FOLLOW THE APPROPRIATE INSTALLATION PROCEDURE TO ATTACH THE DRIVER’S SIDE, AND IF APPLICABLE, THE PASSENGER’S SIDE AND REAR SEAT FLOOR MATS TO THE VEHICLE CARPET USING THE FLOOR MAT RETAINING CLIPS DURING PRE-DELIVERY SERVICE (PDS). |
| T-SB-0037-16 | 2017-02-27. Service bulletin. EQUIPMENT. TSB: SOME 2017 MODEL YEAR VEHICLES ARE EQUIPPED WITH A SMART KEY SYSTEM, WHICH ALLOWS THE CUSTOMER TO ENTER AND START THE VEHICLE WITHOUT USING A MECHANICAL KEY. TO ENSURE THE SYSTEM IS OPERATING PROPERLY, THE SMART KEY FUNCTIONS (SMART ENTRY AND SMART START) SHOULD BE INSPECTED USING THE FOLLOWING PROCEDURE DURING PRE-DELIVERY SERVICE (PDS). NOTE: CHECK ALL OF THE SMART KEYS USING THIS PROCEDURE. |
| T-SB-0076-16 | 2017-01-04. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. TSB: 2017 86 PRE-DELIVERY SERVICE. PRE-DELIVERY SERVICE (PDS) IS A CRITICAL STEP IN SATISFYING THE DEALERSHIP’S NEW CAR CUSTOMERS. CUSTOMER FEEDBACK INDICATES THE FOLLOWING AREAS DESERVE SPECIAL ATTENTION WHEN PERFORMING PDS: *CAREFUL INSPECTION FOR PAINT CHIPS/SCRATCHES AND BODY DENTS/DINGS. PROPER OPERATION OF ELECTRICAL ACCESSORIES (INCLUDING INTERIOR LIGHT, CLOCK, AND RADIO RESET). *INTERIOR CLEANLINESS. *PROPER FUNCTION OF MECHANICAL SYSTEMS. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.