WenmarOpen by Wenmar Pro

Service bulletins for the 2022 Ram 5500

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

436 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Only bulletins with component: Transmission and driveline are shown. Show all

Bulletins, newest first
S1923000015RevB2023-01-09. Service bulletin. POWER TRAIN. Transmission Column Shifter Lever Feels Loose
1803522REVA2022-12-12. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. The customer may experience one or more of the following: Customer may complain of slow PTO idle ramp up. Message will appear "Hot Oil" and exit high idle or PTO mode, when in high idle or PTO mode and running between 10-30 minutes (no load). High frequency exhaust noise at idle after cold start.
21030222022-12-12. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. Flash: Transmission Control Module (TCM) Updates This bulletin involves reprogramming the TCM with the latest available software. Customers may comment on one or more of the following: Harsh shifts. Poor shift quality, with light pedal.(Sales Codes ETM and ETN Only). Poor shift quality, 32-48 kph (20-30 mph), at low rpm with light to medium pedal apply, typically tipping in from zero pedal.(Sales Codes ETM and ETN Only). Coasting shift bump with exhaust brake and/or tow/haul active.(Sales Codes ETM and ETN Only). Poor shift quality, often when increasing pedal during a shift.(Sales Code ESB Only). Squawk/chirp/squeak type noise during a 3-4 upshift.(D2 Only). Poor 1-2 upshift quality.(D2 with ETM or DD/DP with Sales Code ESB Only).
18128222022-10-17. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the Engine Control Module (ECM) / Powertrain Control Module (PCM) with the latest available software.PCM software related to this Technical Service Bulletin (TSB) is included within the Y43 Recall. If not already completed, please perform the Y43 recall if the vehicle is on the recall VIN list. For all other vehicles perform the Repair Procedure below. Customers may experience the following: Idle Instability. The following improvements are also included in this update:wiTECH routine improvement, fuel system run-up test. wiTECH routine improvement, aftertreatment system performance test. Power Take Off (PTO) system improvements.
S22080000732022-10-17. Service bulletin. POWER TRAIN. No Start, After Flash And Or PCM Replace, DTC P0513 Invalid Skim Key Setting
90040092022-09-26. Service bulletin. POWER TRAIN. Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
18-055-222022-06-27. Service bulletin. BACK OVER PREVENTION; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); FUEL SYSTEM, GASOLINE; SERVICE BRAKES, HYDRAULIC; FUEL SYSTEM, DIESEL; EXTERIOR LIGHTING; ELECTRICAL SYSTEM. Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the Engine Control Module (ECM) / Powertrain Control Module (PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set: P0506-00-Idle Control System RPM - Lower Than Expected. P0088 - Fuel Rail Pressure Too High - Bank 1. P0607-00 - ECU Internal Performance. P20E8-00 - Reductant Pressure Too Low. P0301-00 - Cylinder 1 Misfire. P0302-00 - Cylinder 2 Misfire. P0303-00 - Cylinder 3 Misfire. P0304-00 - Cylinder 4 Misfire. P0305-00 - Cylinder 5 Misfire. P0306-00 - Cylinder 6 Misfire. P1C54-00 - SCR NOx Catalyst Missing. P242F-00 - Diesel Particulate Filter Restriction - Ash Accumulation(68RFE Only). P2463-00 - Diesel Particulate Filter Restriction - Soot Accumulation Bank 1(68RFE Only). P1451-00 - Diesel Particulate Filter System Performance(68RFE Only). P0299-00 - Turbocharger Underboost. P2706-00 - MS Solenoid Circuit (68RFE Only). P1D73-00 - AGS Performance. P061B - Internal Control Module Torque Calculation Performance. P064B-00 - PTO Control Module. The customer may also notice the following:PTO Customers: Allows E-Stop to work in any gear. PTO customers that use remote start: Prevents PTO cancellation in cab from disabling remote start. Harsh downshift clunk during exhaust brake deceleration. DEF gauge erratic when DEF level is low. Stall when putting in reverse in cold ambient temps. Engine stumble during engine warm up. Unstable idle when AC compressor cycles. Power Take Off (PTO) intermittently turns off with no DTCs. In addition the following software enhancements are included:Engine oil pressure switch modification. Oil Change Monitor Improvements For Severe Duty Operation. System Improvement for PTO operation. wiTECH Mass Air Flow (MAF) data parameter improvement.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.