P0272 on the 2025 Ram 3500
The bulletins listed name this code in NHTSA's summary, or are about the same components. A bulletin or a recall listed here may apply to the model year. None of it is a diagnosis.
Nobody has written a description of this code yet.
| 18-061-26 | 2026-07-02. Service bulletin. Not applicable to vehicles built for US market. SA Market Only - Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0263-00 - Cylinder 1 Contribution/Balance. ● P0266-00 - Cylinder 2 Contribution/Balance. ● P0269-00 - Cylinder 3 Contribution/Balance. ● P0272-00 - Cylinder 4 Contribution/Balance. ● P0275-00 - Cylinder 5 Contribution/Balance. ● P0278-00 - Cylinder 6 Contribution/Balance. Customers may also comment one or more of the following: ● The engine runs rough and exhibits stumbling and shaking. ● Loss of power. NOTE: The perceived loss of power is due to an insufficient injector/torque response. This bulletin involves inspecting and possibly reprogramming the PCM with the latest available software. |
|---|---|
| 18-014-26 REV. A | 2026-04-29. Service bulletin. Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P0088-00 - Fuel Rail Pressure Too High - Bank 1.** ● P20CF-00 - Exhaust After treatment Fuel Injector "A" Stuck Open. ● P20DB-00 - Exhaust After treatment Fuel Supply Control Stuck Open. ● U0109-00 - Lost Communication With Fuel Pump Control Module. ● P1451-00 - Diesel Particulate Filter System Performance. ● P2463-00 - Diesel Particulate Filter Restriction - Soot Accumulation Bank 1. ● P2459-00 - Diesel Particulate Filter Regeneration Too Frequent. ● P0087-00 - Fuel Rail Pressure Too Low. ● P2540-00 - Low Pressure Fuel System Sensor Circuit Range/performance. ● P2543-00 - Low Pressure Fuel System Sensor Circuit Intermittent. ● P214D-00 - SCR NOX Catalyst Outlet Temperature Too High During Particulate Filter Regeneration. ● P242B-00 - Exhaust Gas Temperature Sensor Circuit Performance - Bank 1 Sensor 3. ● P24DA-00 - Particulate Matter Sensor Exhaust Sample Error Bank 1. ● P20EE-00 - SCR Nox Catalyst Efficiency Below Threshold - Bank 1 Catalyst 1. ● P226C-00 - Turbocharger Boost Control "A" Slow Response. ● P2281-00 - Air Leak Between MAF And Throttle Body. ● P229F-00 - NOX Sensor Circuit Range/performance - Bank 1. ● P0100-00 - Mass Or Volume Air Flow Sensor "A" Circuit. ● P203F-00 - Reductant Level Too Low. ● P0423-00 - Heated Catalyst Efficiency Below Threshold Bank 1. ● P0263-00 - Cylinder 1 Contribution-Balance. ● P0266-00 - Cylinder 2 Contribution-Balance. ● P0269-00 - Cylinder 3 Contribution-Balance. ● P0272-00 - Cylinder 4 Contribution-Balance. ● P0275-00 - Cylinder 5 Contribution-Balance. ● P0278-00 - Cylinder 6 Contribution/Balance. ● P026B-00 - Injection Timing Performance. ● P020A-00 - Cylinder 1 Injection Timing. ● P020B-00 - Cylinder 2 Injection Timing. ● P020C-00 - Cylinder 3 Injection Timing. ● P020D-00 - Cylinder 4 Injection Timing. ● P020E-00 - Cylinder 5 Injection Timing. ● P020F-00 - Cylinder 6 Injection Timing. ● P06B9-00 - Cylinder 1 Glow Plug Circuit Performance. ● P06BA-00 - Cylinder 2 Glow Plug Circuit Performance. ● P06BB-00 - Cylinder 3 Glow Plug Circuit Performance. ● P06BC-00 - Cylinder 4 Glow Plug Circuit Performance. ● P06BD-00 - Cylinder 5 Glow Plug Circuit Performance. ● P06BE-00 - Cylinder 6 Glow Plug Circuit Performance. Customers may also comment on one or more of the following: ● Long engine crank times, particularly after fuel filter change. ● Inverter drops out when shifting from P to D gears. ● Diesel Exhaust Fluid (DEF) level gauge slow to update after a refill. ● Poor cold start performance. ● Cruise control drops out/cancels on its own. ● Engine stumble, runs rough, or a slight lack of power. The following software enhancements are also available: ● Reduce the occurrence of false faults Diagnostic Trouble Codes (DTCs) P0300-00, **P0088-00** and P0315-00. ● Improved troubleshooting and repair accuracy for air handling components through APT test in wiTECH. ● DTC P1451-00 re-tune to reduce false faults. ● Improvements to allow DTC P2509-00 faults to be cleared with wiTECH. ● Adaptive Cruise Control (ACC) software fix to prevent cruise control dropouts. ● Engine stumble fix for improved drivability. ● Engine stall detection allowing DTC P032F-00 to clear after a power cycle. ● Allow multiple PROXI rewrites. ● Enable cold re-prime (DTC P208B-00 improvement) This bulletin involves inspecting and possibly reprogramming the Engine Control Module (ECM/PCM) with the latest available software |
| 18-009-26 REV.A | 2026-03-13. Service bulletin. Flash: Powertrain Control Module (PCM) Updates V2D Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P2540-00 - Low Pressure Fuel System Sensor Circuit Range/Performance. ● P0506-00 - Idle Control System RPM - Lower Than Expected. ● P20CF-00 - Exhaust Aftertreatment Fuel Injector "A" Stuck Open. ● P20DB-00 - Exhaust Aftertreatment Fuel Supply Control Stuck Open. ● P040B-00 - EGR Temperature Sensor 1 Circuit Performance. ● U0109-00 - Lost Communication With Fuel Pump Control Module. ● P1451-00 - Diesel Particulate Filter System Performance. ● P2463-00 - Diesel Particulate Filter Restriction - Soot Accumulation Bank 1. ● P1191-00-Inlet Air Temperature Sensor Rational/Performance. ● P229F-00 - NOX Sensor Circuit Range/Performance - Bank 1. ● P2281-00 - Air Leak Between MAF And Throttle Body.** ● P06B9-00 - Cylinder 1 Glow Plug Circuit Performance. ● P06BA-00 - Cylinder 2 Glow Plug Circuit Performance. ● P06BB-00 - Cylinder 3 Glow Plug Circuit Performance. ● P06BC-00 - Cylinder 4 Glow Plug Circuit Performance. ● P06BD-00 - Cylinder 5 Glow Plug Circuit Performance. ● P06BE-00 - Cylinder 6 Glow Plug Circuit Performance. ● P0263-00 - Cylinder 1 Contribution/balance. ● P0266-00 - Cylinder 2 Contribution-balance. ● P0269-00 - Cylinder 3 Contribution/balance. ● P0272-00 - Cylinder 4 Contribution/balance. ● P0275-00 - Cylinder 5 Contribution/balance. ● P0278-00 - Cylinder 6 Contribution/balance. ● P026B-00 - Injection Timing Performance. ● P020A-00 - Cylinder 1 Injection Timing. ● P020B-00 - Cylinder 2 Injection Timing. ● P020C-00 - Cylinder 3 Injection Timing. ● P020D-00 - Cylinder 4 Injection Timing. ● P020E-00 - Cylinder 5 Injection Timing. ● P020F-00 - Cylinder 6 Injection Timing. T08 FSAR-TSB-6965 -2- ● P0072-00 - Ambient Air Temperature Sensor Circuit "A" Low. ● P0087-00 - Fuel Rail Pressure Too Low. ● P2543-00 - Low Pressure Fuel System Sen |
| 18-014-26 | 2026-02-12. Service bulletin. Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P20CF - 00 Exhaust After treatment Fuel Injector "A" Stuck Open. ● P20DB - 00 Exhaust After treatment Fuel Supply Control Stuck Open. ● U0109 - 00 Lost Communication With Fuel Pump Control Module. ● P1451 - 00 Diesel Particulate Filter System Performance. ● P2463 - 00 Diesel Particulate Filter Restriction - Soot Accumulation Bank 1. ● P2459 - 00 Diesel Particulate Filter Regeneration Too Frequent.** ● P0087-00 - Fuel Rail Pressure Too Low. ● P2540-00 - Low Pressure Fuel System Sensor Circuit Range/performance. ● P2543-00 - Low Pressure Fuel System Sensor Circuit Intermittent. ● P214D-00 - SCR NOX Catalyst Outlet Temperature Too High During Particulate Filter Regeneration. ● P242B-00 - Exhaust Gas Temperature Sensor Circuit Performance - Bank 1 Sensor 3. ● P24DA-00 - Particulate Matter Sensor Exhaust Sample Error Bank 1. ● P20EE-00 - SCR Nox Catalyst Efficiency Below Threshold - Bank 1 Catalyst 1. ● P226C-00 - Turbocharger Boost Control "A" Slow Response. ● P2281-00 - Air Leak Between MAF And Throttle Body. ● P229F-00 - NOX Sensor Circuit Range/performance - Bank 1. ● P0100-00 - Mass Or Volume Air Flow Sensor "A" Circuit. ● P203F-00 - Reductant Level Too Low. ● P0423-00 - Heated Catalyst Efficiency Below Threshold Bank 1. ● P0263-00 - Cylinder 1 Contribution-Balance. ● P0266-00 - Cylinder 2 Contribution-Balance. ● P0269-00 - Cylinder 3 Contribution-Balance. ● P0272-00 - Cylinder 4 Contribution-Balance. ● P0275-00 - Cylinder 5 Contribution-Balance. ● P0278-00 - Cylinder 6 Contribution/Balance. ● P026B-00 - Injection Timing Performance. ● P020A-00 - Cylinder 1 Injection Timing. ● P020B-00 - Cylinder 2 Injection Timing. ● P020C-00 - Cylinder 3 Injection Timing. ● P020D-00 - Cylinder 4 Injection Timing. B18 FSAR-TSB-6872 -2- ● P020E-00 - Cylinder |
| 18-009-26 | 2026-02-04. Service bulletin. Flash: Powertrain Control Module (PCM) Updates V2C Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P06B9-00 - Cylinder 1 Glow Plug Circuit Performance. ● P06BA-00 - Cylinder 2 Glow Plug Circuit Performance. ● P06BB-00 - Cylinder 3 Glow Plug Circuit Performance. ● P06BC-00 - Cylinder 4 Glow Plug Circuit Performance. ● P06BD-00 - Cylinder 5 Glow Plug Circuit Performance. ● P06BE-00 - Cylinder 6 Glow Plug Circuit Performance. ● P0263-00 - Cylinder 1 Contribution/balance. ● P0266-00 - Cylinder 2 Contribution-balance. ● P0269-00 - Cylinder 3 Contribution/balance. ● P0272-00 - Cylinder 4 Contribution/balance. ● P0275-00 - Cylinder 5 Contribution/balance. ● P0278-00 - Cylinder 6 Contribution/balance. ● P026B-00 - Injection Timing Performance. ● P020A-00 - Cylinder 1 Injection Timing. ● P020B-00 - Cylinder 2 Injection Timing. ● P020C-00 - Cylinder 3 Injection Timing. ● P020D-00 - Cylinder 4 Injection Timing. ● P020E-00 - Cylinder 5 Injection Timing. ● P020F-00 - Cylinder 6 Injection Timing. ● P0072-00 - Ambient Air Temperature Sensor Circuit "A" Low. ● P0087-00 - Fuel Rail Pressure Too Low. ● P2540-00 - Low Pressure Fuel System Sensor Circuit Range/Performance. ● P2543-00 - Low Pressure Fuel System Sensor Circuit Intermittent. ● P20EE-00 - SCR NOX Catalyst Efficiency Below Threshold - Bank 1 Catalyst 1. ● P203F-00 - Reductant Level Too Low. ● P2698-00 - Exhaust Aftertreatment Fuel Injector "A" Performance. ● P1C54-00 - SCR NOX Catalyst Missing. ● P056E-00 - Cold Start Turbocharger/Supercharger Boost Control "A" Performance. ● P242F-00 - Diesel Particulate Filter Restriction - Ash Accumulation. ● P1451-00 - Diesel Particulate Filter System Performance. M18 FSAR-TSB-6753 -2- ● P0234-00 - Turbocharger Overboost Condition. ● P20E8-00 - Reductant Pressure Too Low. ● P208B-00 - Reductant Pump 1 Control Performance. Customers may also comment on one or more of |
| 18-021-25 REV. B | 2025-10-15. Service bulletin. Flash: Powertrain Control Module (PCM) Updates *Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle must exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0087-00 - Fuel Rail Pressure Too Low. ● P2540-00 - Low Pressure Fuel System Sensor Circuit Range/performance. ● P2543-00 - Low Pressure Fuel System Sensor Circuit Intermittent. ● P214D-00 - SCR NOX Catalyst Outlet Temperature Too High During Particulate Filter Regeneration. ● P242B-00 - Exhaust Gas Temperature Sensor Circuit Performance - Bank 1 Sensor 3. ● P24DA-00 - Particulate Matter Sensor Exhaust Sample Error Bank 1. ● P20EE-00 - SCR Nox Catalyst Efficiency Below Threshold - Bank 1 Catalyst 1. ● P226C-00 - Turbocharger Boost Control "A" Slow Response. ● P2281-00 - Air Leak Between MAF And Throttle Body. ● P229F-00 - NOX Sensor Circuit Range/performance - Bank 1. ● P0100-00 - Mass Or Volume Air Flow Sensor "A" Circuit. ● P203F-00 - Reductant Level Too Low. ● P0423-00 - Heated Catalyst Efficiency Below Threshold Bank 1. ● P0263-00 - Cylinder 1 Contribution-Balance. ● P0266-00 - Cylinder 2 Contribution-Balance. ● P0269-00 - Cylinder 3 Contribution-Balance. ● P0272-00 - Cylinder 4 Contribution-Balance. ● P0275-00 - Cylinder 5 Contribution-Balance. ● P0278-00 - Cylinder 6 Contribution/Balance. ● P026B-00 - Injection Timing Performance. ● P020A-00 - Cylinder 1 Injection Timing. ● P020B-00 - Cylinder 2 Injection Timing. ● P020C-00 - Cylinder 3 Injection Timing. ● P020D-00 - Cylinder 4 Injection Timing. ● P020E-00 - Cylinder 5 Injection Timing. ● P020F-00 - Cylinder 6 Injection Timing. ● P06B9-00 - Cylinder 1 Glow Plug Circuit Performance. ● P06BA-00 - Cylinder 2 Glow Plug Circuit Performance. ● P06BB-00 - Cylinder 3 Glow Plug Circuit Performance. ● P06BC-00 - Cylinder 4 Glow Plug Circuit Performance. ● P06BD-00 - Cylinder 5 Glow Plug Circuit Performance. ● P06BE-00 - Cylinder 6 Glow Plug Circuit Performance. Customers may also comment on one or more of the following: ● **Inverter drops out when shifting from P to D gears. ● Diesel Exhaust Fluid (DEF) level gauge slow to update after a refill. ● Poor cold start performance.** ● Cruise control drops out/cancels on its own. ● Engine stumble, runs rough, or a slight lack of power. The following software enhancements are also available: ● **Improved troubleshooting and repair accuracy for air handling components through APT test in WiTECH. ** ● Reduce the occurrence of false faults Diagnostic Trouble Codes (DTCs) P0300-00 and P0315-00. ● DTC P1451-00 re-tune to reduce false faults. ● Improvements to allow DTC P2509-00 faults to be cleared with wiTECH. ● Adaptive Cruise Control (ACC) software fix to prevent cruise control dropouts. ● Engine stumble fix for improved drivability. ● Engine stall detection allowing DTC P032F-00 to clear after a power cycle. ● Allow multiple PROXI rewrites. ● Enable cold re-prime (DTC P208B-00 improvement). This bulletin involves inspecting and possibly reprogramming the Engine Control Module (ECM/PCM) with the latest available software |
| 18-075-25 REV. A | 2025-10-08. Service bulletin. Flash: Powertrain Control Module (PCM) Updates Customers must experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● **P0263 - 00 Cylinder 1 Contribution/balance. ● P0266 - 00 Cylinder 2 Contribution-balance. ● P0269 - 00 Cylinder 3 Contribution/balance. ● P0272 - 00 Cylinder 4 Contribution/balance. ● P0275 - 00 Cylinder 5 Contribution/balance. ● P0278 - 00 Cylinder 6 Contribution/balance. ● P026B - 00 Injection Timing Performance. ● P020A - 00 Cylinder 1 Injection Timing. ● P020B - 00 Cylinder 2 Injection Timing. ● P020C - 00 Cylinder 3 Injection Timing. ● P020D - 00 Cylinder 4 Injection Timing. ● P020E - 00 Cylinder 5 Injection Timing. ● P020F - 00 Cylinder 6 Injection Timing. ● P06B9 - 00 Cylinder 1 Glow Plug Circuit Performance. ● P06BA - 00 Cylinder 2 Glow Plug Circuit Performance. ● P06BB - 00 Cylinder 3 Glow Plug Circuit Performance. ● P06BC - 00 Cylinder 4 Glow Plug Circuit Performance. ● P06BD - 00 Cylinder 5 Glow Plug Circuit Performance. ● P06BE - 00 Cylinder 6 Glow Plug Circuit Performance. ● P0072 - 00 Ambient Air Temperature Sensor Circuit "A" Low. ● P0087 - 00 Fuel Rail Pressure Too Low. ● P2540 - 00 Low Pressure Fuel System Sensor Circuit Range/Performance. ● P2543 - 00 Low Pressure Fuel System Sensor Circuit Intermittent. ● P20EE - 00 SCR NOX Catalyst Efficiency Below Threshold - Bank 1 Catalyst 1. ● P203F - 00 Reductant Level Too Low. ● P2698 - 00 Exhaust Aftertreatment Fuel Injector "A" Performance.** ● P1C54 - 00 SCR NOX Catalyst Missing. ● P056E - 00 Cold Start Turbocharger/Supercharger Boost Control "A" Performance. ● P242F - 00 Diesel Particulate Filter Restriction - Ash Accumulation. ● P1451 - 00 Diesel Particulate Filter System Performance. ● P0234 - 00 Turbocharger Overboost Condition. ● P20E8 - 00 Reductant Pressure Too Low. ● P208B - 00 Reductant Pump 1 Control Performance. Customers may also comment on one or more of the following: ● **Diesel Exhaust Fluid (DEF) level gauge inaccuracy. ● Poor cold start performance. ● Unable to initiate manual Diesel Particulate Filter (DPF) regen through EVIC.** ● Unable to engage Power Take-Off (PTO) in mobile condition while the vehicle is moving, but has no issue engaging PTO while the vehicle is stationary. ● Engine stalls under high PTO loads at high altitudes. ● PTO does not work during the split-shaft mode. ● Engine/Cab shake during engine shutdown. ● PTO light not blinking when PTO disengaged. ● Poor engine starting performance. ● DEF level gauge fluctuations. ● In cold conditions the engine automatically increases idle speed when in Park to help with warm-up. Once warmed up, it returns to normal idle speed. If the engine is cycling in and out of this elevated idle speed condition, the customer could complain that its not behaving properly. ● Poor alternator charging and battery life **This bulletin involves inspecting and possibly reprogramming the PCM with the latest available software.** |
7 on file from NHTSA, as of 2026-10-19. See them in the bulletin list. A bulletin lists model years: read the document for which vehicles it concerns.