WenmarOpen by Wenmar Pro

Service bulletins for the 2014 Nissan Rogue

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

332 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Bulletins, newest first
NTB140672021-05-10. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM; EQUIPMENT. IF YOU CONFIRM The maintenance interval mileage in the Vehicle Information Display resets to zero with each ON > OFF > ON ignition cycle, ACTION Reprogram the Vehicle Information Display (METER/M&A) per the Service Procedure in this bulletin. See this bulletin for further detail.
NTB14039A2021-05-10. Service bulletin. ELECTRICAL SYSTEM:BODY CONTROL MODULE/BCM; ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM):SOFTWARE. SERVICE INFORMATION If one or both Intelligent Keys cannot be located prior to customer delivery of an Applied Vehicle, refer to the applicable section of this bulletin for Intelligent Key registration instructions. - One (1) Intelligent Key Is Lost ---- Page 2 - Two (2) Intelligent Keys Are Lost ---- Page 3 NOTE - If both Intelligent Keys are lost with the BCM in Transit Mode, the BCM and ECM will need to be replaced. Refer to pages 3 - 5 for more information. See this bulletin for more detail.
PC3042021-05-10. Service bulletin. EQUIPMENT; EQUIPMENT:APPLIANCE:AIR CONDITIONER. Nissan is conducting a dealer inventory inspection of the automatic climate control system operation on 910 specific 2014 Rogue vehicles identified in SERVICE COMM.
NTB10066A2021-05-10. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. SERVICE INFORMATION Related to communication codes U1000, U1001, U1002, U1010: - Always diagnose the communication codes first. - When a module reports a U1000 code, it is typically operating normally; however, there is a communication error external to that module on the CAN network. - U1000 indicates an error. V-CAN diagram or CAN Diag Support Monitor provides data to determine the location of the error. See this bulletin for more information.
PC300A2021-05-10. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM:IGNITION. The original VIN list provided with the initial announcement contained 29 vehicles that are not equipped with push-button ignition. These 29 vehicles are exempt from the repair and are no longer subject to the quality hold.
PC3002021-05-10. Service bulletin. ELECTRICAL SYSTEM; ELECTRICAL SYSTEM:IGNITION. Nissan is conducting a dealer inventory service action to replace the push button ignition switch on 158 specific 2014 Rogue vehicles identified in SERVICE COMM.
NTB140552021-05-10. Service bulletin. TIRES; EQUIPMENT. SERVICE INFORMATION For 2014 - 2015 Rogue (T32) equipped with third row seats: Do not install or add a spare tire to the vehicle. The vehicle is not designed to be equipped with a spare tire. See this bulletin for further detail.
NTB140502021-05-10. Service bulletin. FORWARD COLLISION AVOIDANCE; EQUIPMENT. SERVICE INFORMATION When performing Distance Sensor Alignment, use the corrected specification (L) for positioning the target board. NOTE: The Distance Sensor is used for the Forward Collision Warning (FCW) system. The specification in the ElectronicService Manual (ESM), Section DAS, Driver Assistance Systems, for positioning the Distance Sensor Target Board is incorrect. Use the corrected specification (L) listed in this bulletin.
NTB140482021-05-10. Service bulletin. EQUIPMENT; WHEELS. SERVICE INFORMATION Factory wheel covers are installed on vehicles during Pre Delivery Inspection (PDI). Care must be taken to properly install the wheel covers to avoid damage. Go to SERVICE PROCEDURE in this bulletin for proper wheel cover installation. NOTE: Damage to wheel covers caused by improper installation is not covered under warranty. See this bulletin for further detail.
NTB140472021-05-10. Service bulletin. ELECTRICAL SYSTEM; STRUCTURE. IF YOU CONFIRM: The "front door power window and door lock/unlock switch (RH) finisher" (switch finisher) has a loose fit, causting an excessive gap. See Figure 1. ACTION: 1. Remove the passenger front door finisher (door finisher). - Refer to the Electronic Service Manual (ESM), section INT-Interior, for removal procedure. 2. Install a foam block where shown in SERVICE PROCEDURE. - Use the foam block listed in PARTS INFORMATION. 3. Install the door finisher with a new switch finisher listed in PARTS INFORMATION. - Refer to the ESM, section INT-Interior, for installation procedure. See this bulletin for further detail.
NTB140382021-05-10. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT; ELECTRICAL SYSTEM. SERVICE INFORMATION When registering the Intelligent Keys (I-Keys) to a vehicle for one of the following concerns: * After replacing the BCM. Or * When one of the I-Keys has been lost and needs to be replaced. Or * When additional I-Keys are being added to the vehicle. Always use the following steps to insure proper registration of the I-Keys: 1. First Initialize the BCM. 2. Register all of the vehicle?s ?previously registered? I-Keys to the vehicle first. And then 3. Register any new (additional) I-Keys only after all of the pre-existing I-Keys have been registered. 4. Confirm operations of all I-Keys. Please see this bulletiln for further details.
NTB140322021-05-10. Service bulletin. ELECTRICAL SYSTEM:WIRING. SERVICE INFORMATION Warranty claims coding for repairing wiring harnesses for all Nissan vehicles has changed. This bulletin gives an outline of the technician?s responsibilities in assisting the dealer?s claims administrator to properly code a harness repair. Failure to provide correct information may result in claims suspension or rejection. See this bulletin for further detail.
NTB140262021-05-10. Service bulletin. ELECTRICAL SYSTEM. IF YOU CONFIRM: An electrical issue caused by corrosion in the Main Harness to Body Harness connectors located at the bottom of the driver side A-pillar: Connector numbers M13 to B3 and/or M14 to B4. ACTIONS: 1. Preform repairs to harness connectors as needed. 2. Apply Harness Protector to cover the harness connectors. See this bulletin for further detail.
NTB140212021-05-10. Service bulletin. STEERING; ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. IF YOU CONFIRM The Instrument Lower Panel LH (as shown in Figure 1) molded plastic clip will not stay secured. ACTION Install a shim between the Steering Member and the Instrument Panel and apply felt tape to the Instrument Lower Panel LH with the SERVICE PROCEDURE starting on page 2. Please see this bulletin for further details.
PC2742021-05-10. Service bulletin. EQUIPMENT; WHEELS. Nissan is conducting a Dealer Inventory Inspection to inspect the right front and right rear lug nuts on 372 certain specific 2014 Nissan Rogue and Pathfinder vehicles currently in dealer inventory.
PC2662021-05-10. Service bulletin. EQUIPMENT; EQUIPMENT ADAPTIVE/MOBILITY. Nissan is conducting a customer satisfaction action on certain MY2014 Nissan Rogue SL AWD vehicles to send customers a Cargo Protector accessory that was inadvertently listed on the Monroney label but was not installed.
PC266OL2021-05-10. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; EQUIPMENT. Nissan is conducting a customer satisfaction action on certain MY2014 Nissan Rogue SL AWD vehicles to send customers a Cargo Protector accessory that was inadvertently listed on the Monroney label but was not installed.
NTB140192021-05-10. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. IF YOU CONFIRM The MIL is on with any one of these DTCs alone, or any combination of any of DTCs: * P2765 - CLUTCH B SPEED SENSOR * P0500 - VEH SPEED SEN/CIRC * P1574 - ASCD VHL SPD SEN * P1715 - INPUT SPEED SENSOR * P0720 - VEH SPD SEN/CIR And * Moisture and/or corrosion is present on or around the Secondary Speed Sensor pins. ACTION a. Remove the moisture from the Harness connector with CRC QD (or equivalent) electric cleaner. b. Replace Secondary Speed Sensor shown in Figure 1. Please see this bulletin for further details.
NTB140182021-05-10. Service bulletin. EQUIPMENT; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; EQUIPMENT ADAPTIVE/MOBILITY. IF YOU CONFIRM A rattle coming from the exhaust center tube heat shield, and a heat shield spot weld is detached, ACTION Install a band clamp around the heat shield and over the detached spot weld. See this bulletin for further detail.
PC268A2021-05-10. Service bulletin. EQUIPMENT; STEERING. On a very small percentage of vehicles, the steering column bolt may need to be replaced by the dealership. Nissan is placing the vehicles that have not had the inspection performed on a Quality Hold.
PC2672021-05-10. Service bulletin. EQUIPMENT; STEERING. Nissan is conducting a Dealer Service Action to inspect and, if necessary, replace the steering knuckle on certain specific 2014 Nissan Rogue vehicles currently in inventory.
PC2682021-05-10. Service bulletin. STEERING. Nissan is conducting a Dealer Service Action to inspect the steering column bolt on certain specific 2014 Nissan Leaf and Rogue vehicles currently in dealer inventory only.
NTB08055C2021-05-10. Service bulletin. EQUIPMENT; AIR BAGS. SERVICE INFORMATION Information necessary to service the Supplemental Restraint System (SRS) safely is included in the "RESTRAINTS" section of the Electronic Service Manual (ESM) for each vehicle. IMPORTANT: Turn the ignition switch OFF, disconnect both battery terminals, and wait at least 3 minutes before performing any service on the SRS. See this bulletin for further detail.
PC2602021-05-10. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. Nissan is conducting a Dealer Service Action to inspect the CVT output speed sensor on certain specific 2014 Nissan Altima, Pathfinder, Rogue vehicles currently in dealer inventory only.
NTB12091A2021-05-10. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM); ENGINE. SERVICE INFORMATION Replacement Engine Control Modules (ECMs) for many newer Nissan vehicles are now "Blank" ECMs. Blank ECMs come without software and must be programmed (not reprogrammed) before they will function. See this bulletin for further detail.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.