WenmarOpen by Wenmar Pro

Service bulletins for the 2015 Nissan Altima

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

332 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Bulletins, newest first
NTB15013C2021-05-10. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:INTERNAL:CVT; POWER TRAIN; EQUIPMENT. IMPORTANT: Metal debris and friction material may become trapped in the radiator, cooling hoses, bypass valve or external CVT fluid cooler. This debris can contaminate the newly serviced transmission, control valve or torque converter. In severe cases this debris can block or restrict flow and may cause damage to the newly serviced CVT. SERVICE INFORMATION When a CVT, control valve or torque converter replacement is necessary for one of the applied vehicles, the CVT transmission fluid coolers (radiator based fluid cooler and external auxiliary cooler if present) must be flushed. Please see this bulletin for further details.
NTB15111A2021-05-10. Service bulletin. EXTERIOR LIGHTING:BRAKE LIGHTS; ELECTRICAL SYSTEM; ENGINE. IF YOU CONFIRM The following, or the customer reports the following: - Intermittently there is low power when accelerating, And/or - The stop lamps (brake lights) stay ON after releasing the brake pedal, with the ignition ON or OFF. ACTION - Delete the stop lamp relay and bypass the stop lamp relay circuit. - Replace the stop lamp switch with the one listed in PARTS INFORMATION. See this bulletin for further detail.
NTB15015F2021-05-10. Service bulletin. POWER TRAIN; EQUIPMENT ADAPTIVE/MOBILITY. IF YOU CONFIRM: The customer reports a transmission judder (shake, shudder, single or multiple bumps or vibration) AND One of these DTCs is stored: - P17F0 (CVT_JUDDER (T/M INSPECTION)) - P17F1 (CVT_JUDDER (C/U INSPECTION)) NOTE - If a transmission judder (as described above) is not reported, this bulletin does not apply. - If either P17F0 or P17F1 are not stored, this bulletin does not apply. - NTB15-014, Enhanced Diagnostic Logic For CVT Judder, has reprogramming instructions that may apply. ACTIONS: Perform the SERVICE PROCEDURE, starting on page 3. - Review the Repair Flow Chart in this bulletin. NOTE: Essential Tool Tech Cam (borescope) J-51951 has been sent to dealers. This tool?s attachments make CVTinspection possible. See this bulletin for further detail.
NTB13106E2021-05-10. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); STEERING; ELECTRICAL SYSTEM; BACK OVER PREVENTION. SERVICE INFORMATION If the configuration of the Audio/Navigation unit has not been completed correctly, some of the symptoms that may occur are: * Intermittent or no back up camera operation * No steering wheel switch response to audio inputs * No volume response from volume knob * Volume very loud or very quiet and adjustment is overly sensitive * Equalizer is adjusted so that Bass control is at maximum all the time * DTC U1000 for AVM C/U could be present If the above symptoms occur: * Confirm the configuration of the Audio/Navigation unit is correct. NOTE: Correct configuration of the appropriate control unit will restore correct operation. Audio/Navigation unit configuration is outlined starting on page 2. See this bulletin for further detail.
NTB13099E2021-05-10. Service bulletin. EQUIPMENT; EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM. SERVICE INFORMATION If the Audio Unit needs to be replaced in an Applied Vehicle for any reason: - Write down replacement Audio Unit's registration "code" . - Replace the Audio Unit as instructed in the Electronic Service Manual (ESM) and any applicable bulletins. - Register the replacement Audio Unit with Nissan Owner Services. NOTE: The Apps mode will not function if the Audio Unit serial number (registration code) is not registered. See this bulletin for further detail.
NTB09099A2021-05-10. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER; EQUIPMENT ADAPTIVE/MOBILITY. IF YOU CONFIRM A refrigerant leak at a refrigerant pipe/hose joint location. ACTIONS 1. Inspect the metal surfaces of the pipe/hose joint for damage or contamination. NOTE: Do not replace a refrigerant pipe, hose, or other A/C component if an o-ring seal will solve the leak incident, if it should occur. 2. If no damage is found to the joint metal surfaces, replace the O-ring seal. See this bulletin for further detail.
NTB09131B2021-05-10. Service bulletin. FORWARD COLLISION AVOIDANCE; EQUIPMENT:OTHER:LABELS. SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement "Certification Label" or "VIN Plate / Label" may be needed. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. See this bulletin for further detail.
NTB15014B2021-05-10. Service bulletin. EQUIPMENT; POWER TRAIN:AUTOMATIC TRANSMISSION:INTERNAL:CVT; POWER TRAIN. IF YOU CONFIRM The customer reports a transmission judder (shake, shudder, single or multiple bumps or vibration). NOTE: A new diagnostic logic has been established to enhance the diagnostic process by storing diagnostic trouble codes (DTCs) on Applied Vehicles. The new DTCs are: P17F1 (CVT_JUDDER [C/U INSPECTION]) P17F0 (CVT_JUDDER [T/M INSPECTION]) ACTION 1. Refer to page 4, step 6 in the SERVICE PROCEDURE to confirm this bulletin applies to the vehicle you are working on. NOTE:The current TCM Part Numbers in this bulletin have been updated. The vehicle you are working on may require reprogramming per this bulletin again. 2. If this bulletin applies, reprogram the TCM (Transmission Control Module) See this bulletin for further detail.
NTB15085B2021-05-10. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); POWER TRAIN:AUTOMATIC TRANSMISSION:INTERNAL:CVT; ELECTRICAL SYSTEM:SOFTWARE. IF YOU CONFIRM: The CVT has a delayed engagement when shifting into Drive or Reverse, and there are no DTCs stored in the ECM and/or TCM. ACTION: Refer to page 5, step 6 in the SERVICE PROCEDURE of this bulletin to check if TCM reprogramming applies to the vehicle you are working on. 1. Reprogram the TCM, if reprogramming applies. 2. Inspect the CVT belt per the SERVICE PROCEDURE in this bulletin. 3. Perform CVT repairs based on inspection results. See this bulletin for further detail.
NTB15044B2021-05-10. Service bulletin. EQUIPMENT; FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY:FILLER PIPE AND CAP. SERVICE INFORMATION If the clip for the fuel filler cap tether becomes lost or is detached for any reason, it is no longer necessary to replace the fuel filler cap. The clip or "pin" is now available as a separate service part. NOTE - Do not replace the fuel filler cap if only the pin is needed. See this bulletin for further detail.
NTB160312021-05-10. Service bulletin. ENGINE AND ENGINE COOLING. IF YOU CONFIRM The MIL is ON with P0116 Engine Coolant Temperature (ECT SENSOR) stored, and There are no drivability issues. ACTION 1. Refer to step 6 in the SERVICE PROCEDURE to confirm this bulletin applies to the vehicle you are working on. 2. If this bulletin applies, reprogram the ECM. See this bulletin for further detail.
NTB15084B2021-05-10. Service bulletin. POWER TRAIN. IF YOU CONFIRM: The customer reports a transmission judder (shake, shudder, single or multiple bumps or vibration), AND One of the following DTCs are stored in the TCM: - P17F0 (CVT_JUDDER (T/M INSPECTION)) - P17F1 (CVT_JUDDER (C/U INSPECTION)) NOTE: - If a transmission judder (as described above) is NOT reported by the customer, this bulletin does not apply. - If DTC P17F0 or P17F1 was NOT found stored, this bulletin does not apply. - NTB15-083, Enhanced Diagnostic Logic For CVT Judder, has reprogramming instructions that may apply. ACTIONS: Perform the SERVICE PROCEDURE, starting on page 3. - Review the Repair Flow Chart on page 2. NOTE: Essential Tool Tech Cam (borescope) J-51951 has been sent to dealers. This tool?s attachments make CVT inspection possible. See this bulletin for further detail.
NTB160232021-05-10. Service bulletin. ELECTRICAL SYSTEM; WHEELS; VISIBILITY; ENGINE AND ENGINE COOLING; POWER TRAIN; FUEL SYSTEM, GASOLINE; STEERING; BACK OVER PREVENTION. IF YOU CONFIRM A customer concern of while turning the steering wheel or when driving at low speed (straight or turning), a high pitch power steering noise can be heard. * Only while seated inside the vehicle And * With all of the windows up NOTE: If the audio and/or HVAC systems are turned ON it may be difficult to hear this issue. ACTION Install an Insulator onto the end of the power steering pump motor housing with the Service Procedure starting on the next page. Please see this bulletin for further details.
NTB160212021-05-10. Service bulletin. ELECTRICAL SYSTEM. IF YOU CONFIRM: Any one or a combination of the following after opening and/or closing a door (as it applies): * The auto headlights do not time out after the ignition is set to the OFF position. * The interior lights do not come ON. * Rogue only: The radio will not turn OFF after ignition is turned OFF. * The Vehicle Information Display in the combination meter showing "door ajar" when the doors are closed. * The Remote Engine Start feature is inoperative. ACTION: 1. Remove, and then reinstall, the screw of all four (4) door switches. 2. Confirm whichever issue has been occurring is resolved. NOTE: If the issue(s) is still not resolved, refer to ASIST and the appropriate Electronic Service Manual (ESM) for further diagnosis. Please see this bulletin for further details.
NTB03074J2021-05-10. Service bulletin. EXTERIOR LIGHTING. SERVICE INFORMATION Occasionally customers may notice water vapor or fog in the headlamps. The information, illustrations, and flow chart in this bulletin are provided to help you in determining if an incident for water/condensation in the headlamps is normal or not. Nissan?s new vehicle limited warranty does not cover physically damaged (cracked or broken) headlamps. All current headlamp assemblies are vented to the atmosphere (not sealed). - This is necessary to allow for expansion and contraction of air from temperature "variations" (warmer or colder) without damage to the headlamp. - Moisture in the air sometimes "travels" into and out of the headlamp assembly through these vents. - Certain environmental conditions may cause moisture to condense. - The fogging/cloudiness should disappear over time when the headlamp is in a dry environment. See this bulletin for further detail.
NTB160182021-05-10. Service bulletin. ELECTRICAL SYSTEM. IF YOU CONFIRM The MIL is "ON" with DTC P0603 (ECM BACK UP/CIRCUIT). ACTION 1. Confirm that the battery voltage is 11 volts, or more, with the ignition ON (engine OFF, not running). 2. Erase DTC 3. Perform DTC confirmation steps in the Service Procedure. 4. Confirm 1st trip DTC P0603 is not stored. NOTE: P0603 is often the result of low battery voltage, discharged battery or battery terminal disconnections. Please see this bulletin for furtner details.
NTB15011A2021-05-10. Service bulletin. ELECTRICAL SYSTEM. IF YOU CONFIRM On an Applied Vehicle, one or more of the following is occurring: * A status message "Update Failed !" is displayed with a direction to "Insert update media" while a countdown from 60 is displayed. The audio system then reboots (Nissan Logo appears), and then will restart the countdown. * The center display screen (navigation screen) intermittently goes blank (nothing is displayed) for a few seconds or longer and then returns to normal display. * Continuously reboots (Nissan Logo appears after a loss of soundor freeze condition). * XM channel selection is sometimes not working as normal or shows "XM loading" for long periods of time. * Audio sometimes is not working. * Soundlevels for balance, fader, treble,or bass do not correspond to what is displayed by the audio unit after the ignition is cycled. * Connected iPod freezes after using "Source" button or changing tracks. * Audio preset buttons do not respond when selected. * Calls unintentionally change from "hands free" to "handset". And * The Software version has been confirmed as "not current" (refer to page 3). See this bulletin for further details.
NTB09081C2021-05-10. Service bulletin. VISIBILITY. SERVICE INFORMATION The purpose of this bulletin is to give Nissan dealers guidelines to help determine if windshield breakage is covered under warranty or is the customer?s responsibility. Nissan North America (NNA) is not responsible for damage to glass that is a result of objects striking or scratching the glass. However, NNA is responsible for manufacturing issues such as distorted glass and cracks that are due to improper installation or damage to the glass during vehicle assembly. NNA typically does not find any type of cracks in the windshield due to stress after the dealership PDI. See this bulletin for further detail.
NTB151022021-05-10. Service bulletin. BACK OVER PREVENTION; POWER TRAIN. IF YOU CONFIRM: A whine or grind type noise heard during acceleration and/or constant highway speeds. -The level of noise may increase as vehicle speed increases AND there are no other drivability issues or stored DTCs related to the CVT assembly (CVT). ACTION: Refer to the REPAIR FLOW CHART on page 3 for repair procedure. Refer to page 2 for information on special service tools. NOTE: Parts Kit #1 (see PARTS INFORMATION) must be available at the time the reduction gear bearing shim selection procedure, starting on page 11, is to be performed. See this bulletin for further detail.
NTB160082021-05-10. Service bulletin. ELECTRICAL SYSTEM. SERVICE INFORMATION The function to detect the last item to trigger the vehicles theft alarm system can now be accessed with CONSULT-III plus (C-III plus). This function can be accessed by selecting: * Diagnosis (All Systems) or Diagnosis (One System). Then * BCM Then * THEFT ALM Then * Work Support Then * THEFT ALM TRG. See this bulletin for further details.
NTB160012021-05-10. Service bulletin. ELECTRICAL SYSTEM. SERVICE INFORMATION When the BCM in an APPLIED VEHICLE is being replaced for any reason, all existing Intelligent Keys must be re-registered. If new Intelligent Keys are added to the existing Intelligent Keys at the same time the BCM is being replaced, the procedure in this bulletin must be followed. See this bulletin for further detail.
NTB151152021-05-10. Service bulletin. FUEL SYSTEM, GASOLINE. IF YOU CONFIRM: There are no drivability issues. and The MIL is ON with one or more of the following Air Fuel (A/F) Sensor DTCs stored: - P0171 - FUEL SYS-LEAN-B1 (System too lean bank 1) - P0172 - FUEL SYS-RICH-B1 (System too rich bank 1) - P2096, P2097 - POST CAT FUEL TRIM SYS B1 - P015A - Air fuel ratio (A/F) sensor 1 (bank 1) ACTION: 1. Refer to step 6 in the SERVICE PROCEDURE to confirm this bulletin applies to the vehicle you are working on. 2. If this bulletin applies, reprogram the ECM and replace the A/F sensor. CAUTION: The ECM must be reprogrammed (if it applies) before the A/F sensor is replaced.
NTB160032021-05-10. Service bulletin. ELECTRICAL SYSTEM. SERVICE INFORMATION The Intelligent Keys used on the various Nissan vehicles may not be interchangeable between models and years. See this bulletin for further detail.
NTB09022G2021-05-10. Service bulletin. ELECTRICAL SYSTEM. SERVICE INFORMATION Design and process changes have been made to improve battery voltage at dealer receipt. Our goal is to deliver vehicles to customers with a 12 volt battery in excellent condition. Proper dealership storage and maintenance of vehicle 12 volt batteries is essential to insuring good battery operating life and customer satisfaction. Dealers are responsible for maintaining vehicles in their inventory. 12 volt batteries in vehicle inventory should always be kept at a full charge to prevent excessive discharge during storage and so they are ready for delivery to customers at any time. See this bulletin for further detail.
NTB14068A2021-05-10. Service bulletin. VISIBILITY. SERVICE INFORMATION Power moonroof initialization procedures for the Applied Vehicles have been revised. The procedure described in this bulletin differs from the procedure in the Electronic Service Manual (ESM). At a later date and where possible, the applicable ESMs will be updated with the revised procedures. Follow the procedure in this bulletin should the power moonroof in an Applied Vehicle need to be initialized. See this bulletin for further details.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.