WenmarOpen by Wenmar Pro

Service bulletins for the 2023 Mercedes-Benz Sprinter

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

108 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Bulletins, newest first
LI14.20-N-079253_32025-07-01. Service bulletin. ENGINE. Check engine light with fault code P300E55 with H12 Complaint The check engine light is activated, accompanied by the following fault code related to the Exhaust gas recirculation cooler (low pressure): •P300E55 The efficiency of component 'Exhaust gas recirculation cooler (low pressure)' is not sufficient. Cause The issue is attributed to an error in the coding of the climate control unit software (HVAC177). Remedy Software Update Instructions Please proceed as follows for the different variants:
LI01.10-N-079275_12025-07-01. Service bulletin. ENGINE. Internal Diesel Engine Damage or Oil Sludge Formation Complaint Customer reports that the vehicle will not start, is difficult to start, or is making unusual noises. Inspection Findings: Upon inspection, engine bearings—including crankshaft, connection rod, and camshafts—exhibit significant signs of wear. Engine oil shows evidence of sludging, characterized by the presence of thick, gel-like, or semi-solid deposits within the engine. This condition is indicative of oil degradation and/or contamination. Cause Internal engine wear and starting issues are a result of oil sludging. This sludging occurs due to oil degradation and/or contamination. Common contributing factors include: •Failure to perform maintenance on time as indicated by the ASSYST PLUS system •Use of non-OEM (aftermarket) parts or fluids •Addition of incorrect fluids (e.g., AdBlue, washer fluid, coolant) to the engine oil, which can severely compromise lub- rication and engine operation Important: Under no circumstances should any non-engine fluids—such as AdBlue, washer fluid, or coolant—be ad- ded to the engine oil or crankcase. The introduction of these fluids, even in small amounts, can cause severe engine damage. This damage is not covered under warranty. Always verify that only approved engine oil and additives are used during service. Remedy To thoroughly diagnose internal engine wear or oil sludging, follow these guidelines: Maintenance History •Verify maintenance intervals: Check that all maintenance has been performed on schedule as indicated by the ASSYST PLUS system in the Instrument Cluster and according to WIS. (Refer to Attachments) •Review records: Examine the vehicle’s service history using resources like VMI, CarFax, and any documentation pro- vided by the customer. •Validate parts and fluids: Confirm all maintenance was carried out using OEM-approved parts and fluids as specified in the Owner’s Manual and Maintenance Booklet.
LI49.20-N-0791572025-06-03. Service bulletin. ENGINE. Complaint The check engine light is activated, accompanied by one or more of the following fault codes related to the Adblue System: •P20F409: The Adblue consumption is too low. There is a component fault. •P202E84: The Adblue metering valve 1 (Motor side) has a malfunction. There is a signal below the permissible limit value. Cause The potential causes for these fault codes are: A. A leak in the Adblue System B. An internal fault with the Adblue Injection Valve #1 (Motor side) C. An air pocket forming in the Adblue Injection Valve #1 (Motor side) Adblue Injector Line Remedy --Prior To Production Date 08/01/2024 Code XY4 = MY24-- A. A Leak in the Adblue System 1. Complete the Guided Tests for P20F409 or P202E84: •Perform a thorough inspection of the Adblue Tank, the Adblue Pump, the Adblue Line, and both Adblue Injectors for leaks. •Ensure the Adblue line is properly installed, securely fastened in all clips, and not in contact with the exhaust system. •Remove both Adblue Injection Valves and complete 2-3 pressure build-ups and inspect for Adblue leakage. •If a leak is identified, repair it and retest. B. An internal fault with the Adblue Injection Valve #1 (Motor side) 1. Process Other Fault Codes First: •If there are other fault codes for the Adblue Injection Valves, address these first. •If the Adblue Injection Valve #1 (engine side) fails the guided tests, replace it and retest. C. An air pocket forming in the AdBlue Line (Motor side) 1. If Guided Tests Pass and No Leaks are Found: •Do not replace any components. •Germany has identified the root cause of fault code P20F409 and is working on a solution. The design of the MY23-24, Code XY4 = MY24, OM654 AdBlue Line (A907 470 01 01) is causing air pockets in the system, resulting in fault code P20F409. Depending on the size of the air pocket, you may also encounter fault code P202E84 AdBlue Metering Valve 1 (Motor side). •The guided tests for fault code P20F409 have been updated to include the resetting of learned values for component ‘A103m1 (AdBlue delivery pump)’ and to release the vehicle back to the client.
LI14.20-N-0792532025-06-03. Service bulletin. ENGINE. Complaint The check engine light is activated, accompanied by the following fault code related to the Exhaust gas recirculation cooler (low pressure): •P300E55 The efficiency of component 'Exhaust gas recirculation cooler (low pressure)' is not sufficient. Cause The issue is attributed to an error in the coding of the climate control unit software (HVAC177). Remedy A software update to correct the coding error is currently in the process of release for the Aftersales network. In the interim, please proceed as follows: •Erase the fault memory (DTCs) from the control unit. •Return the vehicle to the customer. •No further diagnostic or repair procedures are required at this time.
LI14.20-N-0738672025-06-03. Service bulletin. ENGINE. Complaint Complaint A: The engine is jolting/bucking between 1700 and 1900 rpm. Complaint B: One or more mechanical related fault codes for EGR Valve stored in CDI control unit, with possible Check Engine Light. Review list of mechanical fault codes in table below. NOTE: If one or more electrical related fault codes for EGR Valve are also present in CDI, utilize Complaint C. Review list of electrical fault codes PDF document in attachments. Complaint C: One or more electrical related fault codes for EGR Valve stored in CDI control unit, with possible Check Engine Light. Review list of electrical fault codes PDF document attached. Cause Cause of Complaint A: Increased friction between the EGR Valve blade and seat due to soot deposits causing a delay of the EGR Valve being able to reach the target value of the EGR Valve position controller. NOTE: This causes the EGR Valve blade and potentially the boost pressure controller to oscillate. Cause of Complaint B: Soot deposits between the EGR Valve blade and seat leading to the EGR Valve no longer being able to meet the desired target of the EGR Valve position controller. Cause of Complaint C: Internal EGR Valve or other electrical faults related to the EGR Valve function.
LI49.20-N-0791572025-05-02. Service bulletin. ENGINE. Check engine light with possible Adblue warning with fault code P20F409 or P202E84 Complaint The check engine light is activated, accompanied by one or more of the following fault codes related to the Adblue System: •P20F409: The Adblue consumption is too low. There is a component fault. •P202E84: The Adblue metering valve 1 (Motor side) has a malfunction. There is a signal below the permissible limit value. Cause The potential causes for these fault codes are: A. A leak in the Adblue System B. An internal fault with the Adblue Injection Valve #1 (Motor side) C. An air pocket forming in the Adblue Injection Valve #1 (Motor side) Adblue Injector Line Remedy --Prior To Production Date 08/01/2024-- A. A Leak in the Adblue System 1. Complete the Guided Tests for P20F409 or P202E84: •Perform a thorough inspection of the Adblue Tank, the Adblue Pump, the Adblue Line, and both Adblue Injectors for leaks. •Ensure the Adblue line is properly installed, securely fastened in all clips, and not in contact with the exhaust system. •Remove both Adblue Injection Valves and complete 2-3 pressure build-ups and inspect for Adblue leakage. •If a leak is identified, repair it and retest.
LI14.20-N-0738672025-05-02. Service bulletin. ENGINE. EGR Valve Diagnosis and Cleaning Procedure using TUNAP 926® on 906, 907 Sprinter with OM642 Diesel Engine Complaint Complaint A: The engine is jolting/bucking between 1700 and 1900 rpm. Complaint B: One or more mechanical related fault codes for EGR Valve stored in CDI control unit, with possible Check Engine Light. Review list of mechanical fault codes in table below. NOTE: If one or more electrical related fault codes for EGR Valve are also present in CDI, utilize Complaint C. Review list of electrical fault codes PDF document in attachments. Complaint C: One or more electrical related fault codes for EGR Valve stored in CDI control unit, with possible Check Engine Light. Review list of electrical fault codes PDF document attached. NOTE: This LI supersedes LI14.20-N-073813, which is no longer valid. Cause Cause of Complaint A: Increased friction between the EGR Valve blade and seat due to soot deposits causing a delay of the EGR Valve being able to reach the target value of the EGR Valve position controller. NOTE: This causes the EGR Valve blade and potentially the boost pressure controller to oscillate. Cause of Complaint B: Soot deposits between the EGR Valve blade and seat leading to the EGR Valve no longer being able to meet the de- sired target of the EGR Valve position controller. Cause of Complaint C: Internal EGR Valve or other electrical faults related to the EGR Valve function.
LI09.41-N-079165_12025-05-02. Service bulletin. ENGINE. Low Coolant Warning, Potential Misfire, and Absence of External Coolant Leaks Complaint Low Coolant warning with possible engine misfire caused by a leaking Charge Air Cooler (Intercooler), accompanied by one or more of the following possible fault codes related to the coolant system: P30040B: Component 'Temperature sensor downstream of charge air cooler' has an open circuit or short circuit to po- sitive. P25567B: Sensor 'Coolant level' has a malfunction. The fluid level is too low. Cause The potential causes for this topic are: A. A leak in the Coolant System, other than the Charge Air Cooler. B. An Internal leak of the Charge Air Cooler. C. An unapproved/aftermarket upfit or modification to the coolant system. Remedy A. A leak in the Coolant System, other than the Charge Air Cooler 1. Complete a coolant system pressure test: •Refer to WIS Doc AR20.00-D-1011TS - Check engine cooling system for leak tightness. •Use Tester Cap 210 589 00 91 and Pressure Pump 124 589 24 21 00. •Apply test pressure to the engine cooling system. Do not exceed the specified test pressure of 1.5 Bar to prevent da- mage to the engine cooling system. •Perform a visual check on the top and bottom of the engine compartment and in the vehicle interior. •If coolant loss or pressure loss is present, perform suitable repair measures depending on the vehicle equipment. •If NO signs of coolant loss are found but pressure loss is present, proceed to Step B.
LI09.40-N-079144_42025-05-02. Service bulletin. ENGINE. Check engine light with reduced power with fault codes P300A6D, P300974, P300DFB, or P300DE8 Complaint: The check engine light is activated, accompanied by one or more of the following fault codes related to the Boost Pressure Positioner: • P300A6D The boost pressure is too low. Charge Air Cooler. • P300974 Component 'Boost pressure positioner' has a malfunction. The boost pressure is too low. • P300DFB Component 'Boost pressure positioner' has a malfunction. • P300DE8 Boost pressure control A has a malfunction after the cold start. Cause: The potential causes for these fault codes are: A. Leak or Blockage in the Intake or Charge Air System: This can prevent the proper flow of air, affecting the boost pressure. B. Insufficient Source Vacuum, Vacuum Leak, or Sticking/Weak Vacuum Component: These issues can prevent the boost pressure positioner from functioning correctly. C. Internal Malfunction of the Boost Pressure Positioner: The component itself may be faulty. D. Internal Defect with the Variable Turbine Geometry (VTG) System inside the Turbocharger: Issues within the turbo-charger can affect boost pressure control.
LI01.20-N-079115_12025-05-02. Service bulletin. ENGINE. Check engine light illuminated - Fault code current P04D-B79 The crankcase ventilation system is interrupted. Complaint: Check engine light on. Fault code P04DB79 is current in the engine control module (N3/10). Cause: Open circuit or high resistance to crankcase vent line contact Remedy 1. Check the electrical connector for S208 vent line contact switch. Refer to attached photo of connection location. 2. Ensure the bolted connection is secure and bolt can be torqued (9Nm). 3. Check continuity from vent line connection to ME control unit. Repair wire if damage is found.
LI82.35-N-0789302025-04-03. Service bulletin. VISIBILITY/WIPER. Warning Lamp "Washer Fluid Empty" Yet Reservoir Is Not Empty Complaint: Warning lamp "washer fluid empty", even thought the washer fluid reservoir is full Cause: Insufficient electrical conductivity of the washer fluid, as the washer fluid was mixed with distilled water. Tip: The washer fluid sensor detects the electrical conductivity. If air is present without electrical conductivity between the measuring points, as is the case with an empty tank, an empty tank is detected by the sensor. Distilled water also does not have electrical conductivity, meaning that the sensor detects an empty tank, even if this is not the case. Remedy: Fill reservoir with standard washer fluid and water (no distilled water) in an adequate ratio in order to ensure electrical conductivity. Exchange of the reservoir with a welded-in sensor is only required if filling with conductive washer fluid has not provi- ded a remedy. This can be made certain by utilizing water with a light amount of salt dissolved in to it for stronger con- ductivity.
LI49.20-N-0788382025-04-03. Service bulletin. FUEL/PROPULSION SYSTEM. Check engine light or Adblue warning with fault codes P206B31, P203B31, or P300494 when outside temperatures are below 32 degrees Fahrenheit. SCR Gen4 (KP7) Complaint: The check engine light or AdBlue warning is activated, accompanied by one or more of the following fault codes rela- ted to the AdBlue tank: P206B31: Malfunction of the concentration sensor for AdBlue; the signal is absent. P203B31: Malfunction of the AdBlue fill level sensor; the signal is absent. P300494: The quality of the AdBlue is insufficient. Cause: A. The software for the AdBlue (SCR) control unit (N118/5) is outdated. B. The concentration of AdBlue is either above or below the Mercedes-Benz specifications, which can lead to prema- ture freezing. C. Frozen or partially frozen AdBlue can cause the AdBlue level sensor to misread levels. D. The AdBlue level sensor is damaged.
LI49.20-N-0759952025-04-03. Service bulletin. ENGINE. Vehicles with SCR Generation 4: SCR/AdBlue® warning message cannot be reset with fault code P13DF00 or P300685 Complaint: Vehicles with SCR Generation 4: SCR/AdBlue® warning message cannot be reset. Information: All fault codes in the AdBlue® (SCR) control unit have been processed and corrected; however, fault codes P13DF00 and P300685 remain active and stored in the AdBlue® (SCR) control unit. Cause: The procedure for resetting the SCR/AdBlue® warning message with XENTRY Diagnosis has not been carried out. Information: Before resetting the SCR/AdBlue® warning message for SCR Generation 4, the AdBlue® system must be in proper working condition and tested.
LI47.10-N-0790102025-04-03. Service bulletin. FUEL/PROPULSION SYSTEM. Procedure for When Diesel Fuel Tank is Filled with Incorrect Fuel Type Complaint: Procedure for When Diesel Fuel Tank is Filled with Incorrect Fuel Type (e.g., gasoline, water, biodiesel, AdBlue/DEF) Cause: The incorrect fuel type, such as gasoline, water, biodiesel, or AdBlue/DEF has been added to the fuel system.
LI14.20-N-0738672025-04-03. Service bulletin. FUEL/PROPULSION SYSTEM. EGR Valve Diagnosis and Cleaning Procedure Complaint A: The engine is jolting/bucking between 1700 and 1900 rpm. Complaint B: One or more mechanical related fault codes for EGR Valve stored in CDI control unit, with possible Check Engine Light. Review list of mechanical fault codes in table below. NOTE: If one or more electrical related fault codes for EGR Valve are also present in CDI, utilize Complaint C. Review list of electrical fault codes PDF document in attachments. Complaint C: One or more electrical related fault codes for EGR Valve stored in CDI control unit, with possible Check Engine Light. Review list of electrical fault codes PDF document attached. Operation Text: 1. Diagnosis of EGR Valve related concerns including CEL, or drivability concern. 2. Clean EGR Valve. 3. Remove and re-install EGR Valve. 4. Quick Test
LI49.20-N-0788382025-03-04. Service bulletin. FUEL/PROPULSION SYSTEM. Complaint The check engine light or AdBlue warning is activated, accompanied by one or more of the following fault codes rela- ted to the AdBlue tank: P206B31: Malfunction of the concentration sensor for AdBlue; the signal is absent. P203B31: Malfunction of the AdBlue fill level sensor; the signal is absent. P300494: The quality of the AdBlue is insufficient. Cause A. The software for the AdBlue (SCR) control unit (N118/5) is outdated. B. The concentration of AdBlue is either above or below the Mercedes-Benz specifications, which can lead to prema- ture freezing. C. Frozen or partially frozen AdBlue can cause the AdBlue level sensor to misread levels. D. The AdBlue level sensor is damaged. Remedy A. Software 1. Verify no newer software in AdBlue® SCR control unit (N118/5). 2. Complete LI49.20-N-075995 for Adblue warning reset. --NOTE-- If there is no updated software available, proceed to step B. B. Adblue Concentration 1. Verify the AdBlue concentration according to WIS AR49.20-D-9264TS - Check the concentration of AdBlue. --NOTE-- If the AdBlue concentration is below 31.8% or above 33.2%, it must be replaced. Please note that this will be at the customer's expense. 2. If the AdBlue concentration is within the approved specifications, please proceed to step C. C. Frozen Adblue or the SCR Actual Values state 'Frozen Adblue' 1. Check if the AdBlue is frozen. If it is, let the vehicle sit in a warm place overnight and recheck. 2. Have the vehicle running and XENTRY hooked up displaying Adblue level values 3. Drain the Adblue Tank and verify fill level reflects the change in the Adblue level 4. Fill the Adblue Tank SLOWLY and do not overfill, verify fill level reflects the change in the Adblue level --NOTE-- The Fill Level Sensor 1 functions as the "empty sensor." It accurately measures the bottom 60 mm (2.3 in- ches) of the AdBlue tank. Once the tank is filled beyond the 60 mm (2.3 inch) mark, the sensor may not read accura- tely, and you might notice the displayed value fluctuating. This behavior is normal, see attachment 'Fill Level 1'. 5. Reset the Adblue Tank fill level via XENTRY --NOTE-- If the XENTRY still shows that there is frozen Adblue or the concentration is still inaccurate after draining and filling, please refer to the attachments 'Adblue Frozen' and 'Adblue Concentration' and proceed to step C. 6. Complete LI49.20-N-075995 for Adblue warning reset. --NOTE-- If the steps above do not fix the vehicle, please proceed to step D. D. Damaged Adblue Level Sensor/Concentration Sensor 1. Replace the Adblue Tank 2. With the vehicle running and XENTRY hooked up displaying Adblue level values 3. Fill the Adblue Tank SLOWLY and do not overfill, verify fill level reflects the change in the Adblue level 3. Reset the Adblue Tank fill level via XENTRY 4. Complete LI49.20-N-075995 for Adblue warning reset. --NOTE-- During LI49.20-N-075995 for Adblue warning reset, please ensure that the outside temperature sensor is reading above 10 degrees Fahrenheit. If it is not, keep the vehicle inside the shop overnight. Complete LI49.20- N-075995 again. Additionally, please note that the vehicle may need to be driven to allow the NOx sensors and SCR system to complete their self-test. Once this is finished, the P13DF00 code should be stored and can then be cleared. --NOTE-- During cold weather, when temperatures are below 32 degrees Fahrenheit, please advise the client to keep the AdBlue tank fill level between 50% and 85%. This will allow for proper fluid expansion and help prevent damage to the level/concentration sensor.
LI07.70-N-0788242025-03-04. Service bulletin. FUEL/PROPULSION SYSTEM. Complaint Fault code P06DA00 is found current or stored in engine control unit. Check engine light may be activated. Cause Various causes Remedy Up to Model year 2018: Fault code P06DA00 can be disregarded if not activating the check engine light, unless otherwise specified in the gui- ded test. The vehicle continues to operate as designed. Further causes should be investigated if complaint of check engine light is received. Model year 2019 and later: Fault code P06DA00 will activate check engine light as of model year 2019. No driveability concerns will be observed, only illumination of the CEL. This fault code indicates high resistance or open in the circuit to Y130 oil pump control valve. Perform guided test for component Y130 under list of tests in ME. Diagnose location of high resistance or open in Y130 circuit and repair as necessary. Warranty claims submitted without supporting guided test results may be subject to debit.
LI49.20-N-075995_32025-02-06. Service bulletin. ENGINE. Vehicles with SCR Generation 4: SCR/AdBlue warning message cannot be reset (P13DF00)
LI47.50-N-072080_32025-02-06. Service bulletin. ENGINE. Check engine light on and FC P146264 stored in engine and fuel pump control units
LI13.22-N-078825_12025-02-06. Service bulletin. ENGINE. M274 poly-V belt squeaking noises, falls off, not aligned, broken
LI49.20-N-0788382025-02-04. Service bulletin. ENGINE. Check engine light or Adblue warning with fault codes P206B31, P203B31, or P300494 when outside temperatures are below 32 degrees Fahrenheit
LI14.30-N-0758822025-01-03. Service bulletin. ENGINE. Check engine light active Complaint Check engine warning light active. The following fault codes may be present in the engine control unit: • P3007F1 Leak detected in intake air system or • P3007F2 Mass air flow malfunction in intake air system (cylinder bank 1) or • P300CA8 Leak detected in intake air system or • P300CA9 Mass air flow malfunction in intake air system (cylinder bank 1) or • P300CA9 and P3007F1: Faults are present simultaneously in the quick test
LI49.20-N-0784662024-12-04. Service bulletin. ENGINE. Check engine light with fault code P3005CA in MRD1 (CDI) Complaint: The check engine light is on, with a possiblility in a reduction of power and the presence of soot in the exhaust sys- tem. Fault code P3005CA: The diesel particulate filter efficiency is insufficient. Additional information: Additional fault codes may be present, related to the Diesel Particulate Filter (DPF) system or the Exhaust Gas Recirculation (EGR) system. Cause: This fault code sets due to the following factors: 1. Damage to the Diesel Particulate Filter (DPF) unit. 2. The N74 (Soot Particulate Sensor Control Unit) identifies soot or debris located downstream of the SCR Catalyst (underbody).
LI49.00-N-0786082024-12-04. Service bulletin. ENGINE. SMOG/Emissions Test fail due to one or more Readiness Monitors not set Complaint: The vehicle has failed the State Emissions Certification because one or more of the OBDII readiness monitors are not completely set. Cause: One or more of the following Readiness Monitors are not fully set within XENTRY: Misfire Monitoring - Injection System Fuel System Monitoring - Injection System, Fuel System, EGR Valve, O2 Sensor NMHC Catalyst Monitoring - NMHC/Diesel Oxidation Catalyst NOx Aftertreatment Monitoring - SCR Catalyst System Boost Pressure System Monitoring - Turbocharger, Charge Air System Exhaust Gas Sensor Monitoring - O2 Sensor, NOx Sensors Diesel Particulate Filter Monitoring - Diesel Particulate Filter System Exhaust Gas Recirculation System Monitoring - EGR Valve and system Remedy: Please complete the required driving conditions to fully set the incomplete Readiness Monitor. DO NOT: - Erase any fault codes. If fault codes are present, process these and allow the readiness drives to clear fault codes. - Flash or SCN code the CDI or SCR control units. - Perform a manual DPF regeneration, unless instructed below. - Disconnect the main battery.
LI27.00-N-0786112024-12-04. Service bulletin. POWER TRAIN. Pre-Case creation for 725.0/.1 Transmissions Complaint: To insure vehicle down time is kept at a minimum and all required information is available when case is escalated, as well as assist technicians with checks that may help lead in resolving issue without case creation. THIS LI IS NOT TO BE USED AS A REASON FOR CASE CREATION BUT AS A GUIDE IF A CASE IS NEEDED Cause: There are, at times, additional steps workshops can do to help diagnose and rectify transmission complaints. Remedy: When opening a case for transmissions a EEPROM, Quick Test, and VGS CUL are absolutely necessary Please also check for any relevant LI’s before opening case. Also, recommend having customer fill out Transmission Drivability Diagnostic Worksheet especially if complaint is hard to reproduce or intermittent (Work sheet Location: Xentry Portal >> Local Contents >> Diagnostic Info>> Diagnostic Worksheets ) If a previous repair attempt or visit was made for the same concern please include the date, mileage, and case num- ber if applicable of that repair/visit with a short description of what was done. Follow IPR: ( LI27.00-P-073124 ) All IPR suggestions are covered by warranty and there is no need for cases to con- firm IPR. Complete IPR suggestions and close out IPR process. If complaint is not fixed and IPR still suggests the sa- me repair once closed out and run again, then a case may be needed. Transmission Health page is a good indicator of issues within transmission if clutch or brake pack stays NOK after ad- aptions and unable to be made to a green OK then an internal fault is present. Proceed with replacing affected clutch pack.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.