Service bulletins for the 2015 Mazda Mazda6
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
609 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
Only bulletins with component: Equipment and accessories are shown. Show all
| 05-002-15-3019E | 2017-06-07. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH ONE OR MORE OF THESE DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780). • P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ON • P0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ON • P0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ON • P0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ON • P0780:00 - GEAR SHIFTING MALFUNCTION THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO CORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC. NOTE: IF THE VEHICLE ALSO HAS A DELAYED ENGAGEMENT CONCERN, THIS TSB IS NOT APPLICABLE. REFER TO MS3 ONLINE INSTRUCTIONS OR WORKSHOP MANUAL FOR PROPER DIAGNOSIS AND REPAIR PROCEDURE. |
|---|---|
| 09-034-15-3068 | 2017-06-07. Service bulletin. SEATS:FRONT ASSEMBLY:POWER ADJUST; EQUIPMENT:ELECTRICAL. SOME CUSTOMERS MAY COMPLAIN THAT THE FRONT POWER (DRIVER AND/OR PASSENGER) SEATS DO NOT SLIDE BACK AND FORTH PROPERLY OR THAT THEY MAY BE COMPLETELY INOPERATIVE. THIS CONCERN MAY BE CAUSED BY A FOREIGN OBJECT GETTING STUCK UNDER THE POWER SLIDE UNIT (BELOW) WHILE IN OPERATION. THIS CAN CAUSE MOTOR MOUNTING BRACKET (A) DEFORMATION, RESULTING IN MOTOR CABLE (B) BREAKAGE. TO ELIMINATE THIS CONCERN, THE SHAPE OF THE MOTOR MOUNTING BRACKET (A) HAS BEEN MODIFIED TO INCREASE ITS STRENGTH. |
| 01-016-15-3067 | 2017-06-07. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; ENGINE; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT ON WITH DTC P0421:00 (CATALYTIC CONVERTER SYSTEM) WITHOUT EXPERIENCING POOR ENGINE PERFORMANCE OR MISFIRE (MITSUBISHI PCM ONLY). THIS IS CAUSED BY IMPROPER CONTROL LOGIC OF THE PCM THAT MAY DETECT FALSE ERROR OF THE A/F SENSOR, RESULTING IN FALSE DETECTION OF P0421. TO CORRECT THE PROBLEM, THE CONTROL LOGIC OF THE PCM HAS BEEN CHANGED. CATALYST MONITOR FUNCTION EXPLANATION • THE PCM MONITORS THE OXYGEN STORAGE AMOUNT PROPORTIONAL TO CATALYTIC CONVERTER PURIFICATION CHARACTERISTIC. • THE PCM STARTS TO MONITOR AFTER RECOVERY (FUEL INJECTION STARTS) FROM FUEL CUT CONTROL. • THE PCM TEMPORARILY CHANGES THE TARGET AIR/FUEL RATIO TO RICH AT FUEL CUT RECOVERY, AND DETECTS THE RESPONSE TIME UNTIL THE HO2S OUTPUT SIGNAL OUTPUTS THE VOLTAGE ON THE RICH SIDE. • IF THE CATALYTIC CONVERTER PURIFICATION CHARACTERISTIC DETERIORATES, THE AMOUNT OF THE TIME UNTIL THE HO2S DETECTS THE VOLTAGE ON THE RICH SIDE IS SHORTER COMPARED TO THE NORMAL PURIFICATION CHARACTERISTIC AS SHOWN. THE PCM DETECTS A CATALYTIC CONVERTER MALFUNCTION USING THIS CHARACTERISTIC. |
| 01-018-15-3070 | 2017-06-07. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; ENGINE. SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT ON WITH DTC P2610 AND P2507 STORED IN MEMORY AFTER ENGINE START AND ROOM FUSE 15A (A) REMOVED. • P2610:00: INSTRUMENT CLUSTER INTERNAL ENGINE OFF TIMER PERFORMANCE PROBLEM • P2507:00: PCM BATTERY VOLTAGE LOW INPUT AS A PAST MALFUNCTION, THE CUSTOMER WILL NOT NOTICE IT (NO WARNING LIGHT ILLUMINATED), BUT THE DTC MAY BE FOUND DURING A VEHICLE SERVICE. P2507 IN THIS SITUATION IS ONLY APPLICABLE ON 2016 AND LATER MODELS. THIS IS CAUSED BY THE ENGINE BEING STARTED 3 OR MORE TIMES AFTER A SHORT DURATION OF ENGINE OFF (LESS THAN 15 SECONDS) WITH THE ROOM FUSED REMOVED. |
| 09-030-15-3073 | 2017-06-07. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. MAZDA INFOTAINMENT SYSTEMS REQUIRE CONTACTING THE PROPER SOURCE FOR DIAGNOSTIC SUPPORT, PARTS AUTHORIZATION, AND PARTS EXCHANGE. SOME COMPONENTS REQUIRE PRIOR AUTHORIZATION BEFORE ORDERING AS EXCHANGE. REFER TO DAG EXCHANGE CENTRAL (MXCONNECT>PARTS AND ACCESSORIES>PARTS>PROGRAMS>EXCHANGE CENTRAL) FOR COMPONENT AVAILABILITY, SOURCE OF TECHNICAL SUPPORT AND PRIOR AUTHORIZATION REQUIREMENT. NOTE: ALWAYS CHECK FOR A TSB THAT MAY MODIFY OR ELIMINATE PRIOR AUTHORIZATION FOR A SPECIFIC SYMPTOM FOR A GIVEN COMPONENT. |
| 09-031-15-3076 | 2017-06-07. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). THE NAVIGATION SYSTEM SUPPORT FOR DIAGNOSTICS, PARTS AUTHORIZATION, AND PARTS EXCHANGE REQUIRE CONTACTING THE PROPER SOURCE. • TOMTOM NAVIGATION HELP DESK AT 866-486-6866 FROM 7AM-11PM (M-F) AND 9AM-8PM (SAT) EASTERN STANDARD TIME. NOTE: ONE OF THE FIRST STEPS FOR TROUBLESHOOTING THE NAVIGATION SYSTEM IS FOR THE CUSTOMER OR DEALER TO CALL TOMTOM. IF THE TOMTOM CALL CENTER CANNOT SOLVE THE CUSTOMER’S PROBLEM, THEY WILL PROVIDE A CASE NUMBER TO THE CUSTOMER THAT CAN BE REFERRED TO IF NEEDED. SERVICE ADVISORS SHOULD GET THIS CASE NUMBER FROM THE CUSTOMER IF THE VEHICLE COMES INTO THE DEALER FOR FURTHER DIAGNOSIS SO THE TECHNICIAN CAN HAVE IT WHEN CALLING TOMTOM. |
| 09-008-15-2991C | 2017-06-07. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. SOME CUSTOMERS MAY COMPLAIN ABOUT ONE OR MORE OF THE FOLLOWING CONCERNS. 1. SMS/TEXT CANNOT BE DOWNLOADED WHEN ONNECTED VIA BLUETOOTH. 2. OPERATIONAL CONCERNS WHEN PLAYING A MEDIA DEVICE (IPOD, USB STICK ETC.) CONNECTED VIA THE USB PORT. A. AFTER THE IGNITION IS TURNED ON, IT TAKES A LONG TIME TO LOAD ALL THE DATA FROM THE DEVICE BEFORE STARTING PLAYBACK. DEPENDING ON THE DATA VOLUME, IT CAN TAKE UP TO SEVERAL MINUTES. B. AFTER THE IGNITION IS TURNED ON, THE PLAYBACK ALWAYS STARTS FROM THE FIRST TRACK. IT DOES NOT START FROM THE LAST PLAYING TRACK/POSITION WHEN THE IGNITION WAS TURNED OFF. C. “IPOD ERROR” MESSAGE FOR THE APPLE® IOS 8.0 OR HIGHER SOFTWARE ON IPHONE 4, 5, OR 6. THESE CONCERNS MAY BE CAUSED BY THE SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE THAT CONTROLS THE USB CONNECTION. TO IMPROVE THESE CONCERNS, THE SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE HAS BEEN CHANGED. NOTE: • THE UPDATED SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE WILL ONLY ADDRESS SMS/TEXT CONCERNS FOR THE APPLE® IPHONE AT THIS TIME. |
| 01-007-15-3025 | 2017-06-07. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME VEHICLES MAY EXPERIENCE A CHECK ENGINE LIGHT ON WITH DTCS P0011:00 AND/OR DTC P0012:00 STORED IN MEMORY. • P0011:00: ELECTRIC VARIABLE VALVE TIMING CONTROL SYSTEM - OVER-ADVANCED) • P0012:00: ELECTRIC VARIABLE VALVE TIMING CONTROL SYSTEM - (OVER-RETARDED) THIS CONCERN MAY BE CAUSED BY VARIABLE VALVE TIMING (VVT) ACTUATOR SPRING SHAFT FATIGUE. DURING VEHICLE USAGE, THE SPRING SHAFT MAY FAIL AND CAUSE INCORRECT VVT OPERATION AND CHECK ENGINE LIGHT ILLUMINATION. THE INSPECTION PROCEDURE HAS BEEN IMPROVED TO ELIMINATE THIS CONCERN IN THE FUTURE. |
| 01-008-15-3045 | 2017-06-07. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME VEHICLES MAY EXHIBIT THE CHECK ENGINE LIGHT ON WITH DTC P0456 STORED IN THE PCM MEMORY. • P0456: EVAP SYSTEM LEAK DETECTED (VERY SMALL LEAK) THE CONCERN IS MOST LIKELY THE RESULT OF THE CUSTOMER NOT GETTING THE FUEL CAP COMPLETELY CLOSED AFTER FUELING THE VEHICLE. THIS CAUSES A SMALL FUEL VAPOR LEAK AND TURNS DTC P0456 ON. |
| 05-002-15-3019D | 2017-06-07. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH ONE OR MORE OF THESE DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780). • P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ON • P0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ON • P0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ON • P0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ON • P0780:00 - GEAR SHIFTING MALFUNCTION THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO CORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC. |
| 01-015-15-3064A | 2017-05-31. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME VEHICLES USING AN AUXILIARY HEATER (BLOCK HEATER) MAY EXPERIENCE THE CHECK ENGINE LIGHT ON WITH DTC P0116:00 OR P011A WHEN STARTING IN COLD WEATHER BELOW 32 °F (0 °C). • P0116:00: ECT SENSOR NO.1 CIRCUIT RANGE/PERFORMANCE PROBLEM • P011A:00: ECT SENSOR NO.1/NO.2 PERFORMANCE PROBLEM THIS IS CAUSED BY ERROR DETECTION LOGIC OF THE PCM. TO CORRECT THE PROBLEM, THE CONTROL LOGIC OF THE PCM HAS BEEN CHANGED. |
| 01-023-15-3084 | 2017-05-31. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; ENGINE. SOME VEHICLES MAY EXPERIENCE A ROUGH IDLE WITH THE MIL ON AND DTC P0015 / P0524 STORED IN MEMORY. • P0015:00 - EXHAUST CMP TIMING OVER-RETARDED • P0524:00 - ENGINE OIL PRESSURE TOO LOW THIS IS CAUSED BY A DROP IN ENGINE OIL PRESSURE DUE TO A PIECE OF FOREIGN OBJECT STUCK ON THE OIL PUMP PRESSURE RELIEF VALVE OR OCV. THE TEMPORARY ENTRY OF THE FOREIGN OBJECT TRIGGERS A MIL ILLUMINATION, BUT ROUGH IDLE WILL NOT BE PRODUCED UNTIL A LATER TIME. |
| 02-010-16-3170 | 2017-05-30. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; STRUCTURE:FRAME AND MEMBERS; SUSPENSION:FRONT:SHOCK ABSORBER. SOME VEHICLES MAY EXHIBIT A KNOCKING / SQUEAKING NOISE FROM THE FRONT SHOCK ABSORBER WHEN DRIVING ON ROUGH ROADS AND/OR WHEN TURNING THE STEERING WHEEL WHILE THE VEHICLE IS STOPPED. THE NOISE MAY BE DUE TO:•UPPER FRONT STRUT BEARING (A) DAMAGE. (CX-5 AND MAZDA6)•STICK/SLIP BETWEEN THE FRONT STRUT BEARING AND COIL SPRING. (CX-3, CX-5 AND MAZDA6)•THE BUMP STOPPER (C) MAY BE CONTACTING THE STRUT BEARING WHEN THE FRONT SHOCK ABSORBER IS COMPRESSED, CAUSING A POPPING NOISE. (MAZDA6 ONLY)•THE FRONT LOWER ARM BUSHING (D) IS MAKING A STICK-SLIP NOISE IN WET ROAD CONDITIONS. (CX-5 AND MAZDA6)TO ELIMINATE THE NOISE, THE FOLLOWING MASS-PRODUCTION CHANGES HAVE BEEN MADE:1. THE MATERIAL AND PRODUCTION METHOD OF THE FRONT STRUT BEARING (A) HAS BEEN CHANGED. (CX-5 AND MAZDA6)2. A PROTECTOR HAS BEEN INSTALLED ONTO THE COIL SPRING. (CX-5 AND MAZDA6)3. THE SHAPE OF THE BUMP STOPPER (C) WILL BE MODIFIED IN THE FUTURE. (MAZDA6 ONLY)4. THE SHAPE OF THE COIL SPRING HAS BEEN CHANGED. (CX-3 ONLY)5. FRICTION OF THE LOWER ARM BUSHING HAS BEEN REDUCED BY ADDING A DRY COATING. (CX-5 AND MAZDA6)NOTE:THE PISTON ROD NUT (B) REQUIRES REPLACEMENT. |
| 01-009-16-3172 | 2017-05-30. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; ENGINE AND ENGINE COOLING; ENGINE. SOME VEHICLES MAY EXPERIENCE A ROUGH IDLE WITH THE CHECK ENGINE LIGHT ON AND DTC P0015 / P0524 STORED IN MEMORY.•P0015:00 - EXHAUST CMP TIMING OVER-RETARDED•P0524:00 - ENGINE OIL PRESSURE TOO LOWTHIS IS CAUSED BY A DROP IN ENGINE OIL PRESSURE DUE TO A PIECE OF FOREIGN OBJECT STUCK ON THE OIL PUMP PRESSURE RELIEF VALVE OR OIL CONTROL VALVE (OCV). THE TEMPORARY ENTRY OF THE FOREIGN OBJECT TRIGGERS A CHECK ENGINE LIGHT ON, BUT ROUGH IDLE WILL NOT BE PRODUCED UNTIL A LATER TIME. |
| 07-002-15-3004 | 2017-05-25. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER. SOME CUSTOMERS MAY COMPLAIN ABOUT NO COOL AIR FROM THE VENTS WHEN THE AIR CONDITIONER (A/C) IS ON. THIS CONCERN MAY BE CAUSED BY A/C REFRIGERANT LEAKING FROM THE EVAPORATOR. SOME DEFORMED EVAPORATOR TUBES SLIPPED THROUGH QUALITY INSPECTION AND WERE USED DURING PRODUCTION. A/C REFRIGERANT LEAKS FROM IMPROPER BRAZING AT A JOINT. TO CORRECT THE PROBLEM, THE PRODUCTION AND INSPECTION CONTROL OF THE EVAPORATOR HAVE BEEN IMPROVED. |
| 02-003-15-2990 | 2017-05-25. Service bulletin. EQUIPMENT:MECHANICAL. SOME VEHICLES MAY EXHIBIT A KNOCKING / SQUEAKING NOISE FROM THE FRONT STRUT BEARING (A) WHEN DRIVING ON ROUGH ROADS AND/OR WHEN TURNING THE STEERING WHEEL WHILE THE VEHICLE IS STOPPED. THE NOISE MAY BE DUE TO UPPER FRONT STRUT BEARING DAMAGE OR IT MAY BE DUE TO STICK/SLIP BETWEEN THE FRONT STRUT BEARING AND COIL SPRING. TO ELIMINATE THE NOISE, THE FOLLOWING MASS-PRODUCTION CHANGES HAVE BEEN MADE: 1. THE MATERIAL AND PRODUCTION METHOD OF THE FRONT STRUT BEARING HAS BEEN CHANGED. 2. A PROTECTOR HAS BEEN INSTALLED ONTO THE COIL SPRING. NOTE: THE PISTON ROD NUT (B) REQUIRES REPLACEMENT WHEN THE FRONT STRUT BEARING IS REPLACED. |
| 01-003-15-3014 | 2017-05-25. Service bulletin. EQUIPMENT. USE THE FOLLOWING REPAIR PROCEDURE TO MINIMIZE THE NEED TO REPLACE THE CATALYST CONVERTER/EXHAUST PIPE WHEN REMOVING OXYGEN SENSORS AND/OR AIR FUEL RATIO SENSORS. |
| 09-009-15-3015 | 2017-05-25. Service bulletin. EQUIPMENT. SOME VEHICLES MAY EXPERIENCE STAINS APPEARING ON THE HOOD, ROOF AND/OR TRUNK OF THE VEHICLE. THIS CONCERN IS MOST LIKELY TO BE FOUND IN A COLD WEATHER AREAS JUST AFTER THE RAPGARD IS REMOVED AT PDI. THIS MAY BE CAUSED BY MOISTURE WHICH HAS BEEN TRAPPED AND CONDENSED BETWEEN THE PAINT AND THE RAPGARD. THESE TYPES OF STAINS CAN BE REMOVED WITH A HEAT GUN OR AN INFRARED DRIER. IF YOU ENCOUNTER THIS CONCERN DURING PDI, USE A HEAT GUN OR AN INFRARED DRIER TO APPLY HEAT TO THE AFFECTED AREA TO REMOVE THE STAIN(S). |
| 05-002-15-3019C | 2017-05-19. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH ONE OR MORE OF THESE DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780). • P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ON • P0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ON • P0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ON • P0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ON • P0780:00 - GEAR SHIFTING MALFUNCTION THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO CORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC. |
| 02-005-14-2981 | 2017-05-19. Service bulletin. EQUIPMENT. SOME VEHICLES MAY EXHIBIT A CREAKING NOISE FROM UNDER THE FRONT OF THE VEHICLE WHEN DRIVING OVER BUMPS. THE NOISE OCCURS AT APPROX. 12 - 25 MPH (20 - 40 KM/H) WHEN THE ROAD SURFACE IS WET OR AFTER A CAR WASH. THE NOISE BECOMES MORE NOTICEABLE WHEN DRIVING OVER HIGHER BUMPS. THE CREAKING NOISE IS CAUSED WHEN THE FRONT LOWER CONTROL ARM BUSHING(S) (A) BECOME WET. |
| 00-004-14-2983 | 2017-05-19. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. IN SUPPORT OF THE SKYACTIV MODELS, MAZDA WILL MAKE AVAILABLE A SPECIAL SERVICE TOOL (SST), TO ADDRESS FRONT SUSPENSION NOISE FOR SPECIFIC HIGH HUMIDITY AND WET CLIMATE CONDITIONS IN THE LOWER GULF STATES. THE SST WILL BE NEEDED TO COMPLETE REPAIRS DETAILED IN TSB 02-005/14 AND IS AVAILABLE THROUGH MAZDA’S TOOL VENDOR, SNAP-ON TOOLS. |
| 02-006-14-2994 | 2017-05-19. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. AFTER PERFORMING RECALL CAMPAIGN 8014J, SOME VEHICLES MAY EXPERIENCE TIRE PRESSURE MONITORING SYSTEM (TPMS) WARNING LIGHT ON EVEN IF THE TPMS SYSTEM HAS BEEN PROPERLY INITIALIZED AT THE SPECIFIED TIRE AIR PRESSURE. THIS MAY BE CAUSED BY IMPROPER TIRE AIR PRESSURE DETECTION BY THE TPMS SYSTEM ON CERTAIN TYPES OF ROAD SUR-FACES. |
| 08-001-15-3017 | 2017-05-18. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME VEHICLES MAY EXHIBIT INSTRUMENT CLUSTER TPMS, ABS AND TCS/DSC INDICATOR WARNING LIGHTS ON AND DTC U3000:49[STANDARD DEPLOYMENT CONTROL SYSTEM] OR C0061:29, C0062:29, C0063:29 [STANDARD DEPLOYMENT CONTROL SYSTEM] STORED IN MEMORY. THE AIRBAG, SCBS, AT, MRCC, LDWS AND HBC INSTRUMENT CLUSTER INDICATOR LIGHTS MAY ALSO COME ON. INTERNAL FAILURE OF THE SAS CONTROL MODULE MAY BE THE CAUSE. |
| 05-002-15-3019 | 2017-05-18. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME VEHICLES MAY EXPERIENCE THE CHECK ENGINE LIGHT AND AUTOMATIC TRANSAXLE WARNING LIGHT ON WITH ONE OR MORE OF THESE DTCS STORED IN THE TCM MEMORY (P0842, P0847, P0872, P0877, P0780). • P0842:00 - OIL PRESSURE SWITCH NO. 1 (OIL PRESSURE SWITCH B) STUCK ON • P0847:00 - OIL PRESSURE SWITCH NO. 2 (OIL PRESSURE SWITCH A) STUCK ON • P0872:00 - OIL PRESSURE SWITCH NO. 3 (OIL PRESSURE SWITCH A) STUCK ON • P0877:00 - OIL PRESSURE SWITCH NO. 4 (OIL PRESSURE SWITCH B) STUCK ON • P0780:00 - GEAR SHIFTING MALFUNCTION. THIS IS CAUSED BY THE OIL PRESSURE SWITCH A AND/OR B AT THE CONTROL VALVE BODY TEMPORARILY OR PERMANENTLY GETTING STUCK DUE TO CONTAMINATION ENTERING THE PASSAGE. TO ORRECT THE PROBLEM, SOME MASS PRODUCTION CHANGES HAVE BEEN IMPLEMENTED TO REDUCE CONTAMINATION AND IMPROVE THE DTC DIAGNOSTIC LOGIC. |
| 09-008-15-2991A | 2017-05-18. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME CUSTOMERS MAY COMPLAIN ABOUT ONE OR MORE OF THE FOLLOWING CONCERNS. 1. SMS/TEXT CANNOT BE DOWNLOADED WHEN CONNECTED VIA BLUETOOTH. 2. OPERATIONAL CONCERNS WHEN PLAYING A MEDIA DEVICE (IPOD, USB STICK ETC.) CONNECTED VIA THE USB PORT. A. AFTER THE IGNITION IS TURNED ON, IT TAKES A LONG TIME TO LOAD ALL THE DATA FROM THE DEVICE BEFORE STARTING PLAYBACK. DEPENDING ON THE DATA VOLUME, IT CAN TAKE UP TO SEVERAL MINUTES. B. AFTER THE IGNITION IS TURNED ON, THE PLAYBACK ALWAYS STARTS FROM THE FIRST TRACK. IT DOES NOT START FROM THE LAST PLAYING TRACK/POSITION WHEN THE IGNITION WAS TURNED OFF. THESE CONCERN MAY BE CAUSED BY THE SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE THAT CONTROLS THE USB CONNECTION. TO IMPROVE THESE CONCERNS, THE SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE HAS BEEN CHANGED. NOTE: • THE UPDATED SOFTWARE OF THE BLUETOOTH/HANDS-FREE MODULE WILL ONLY ADDRESS SMS/TEXT CONCERNS FOR THE APPLE® IPHONE AT THIS TIME. • THE UPDATED SOFTWARE OF THE BLUETOOTH/HANDSFREE MODULE WILL NOT ADDRESS THE “IPOD ERROR” MESSAGE CONCERN FOR THE APPLE® IOS 8.0 OR HIGHER SOFTWARE ON IPHONE 4, 5, OR 6 AT THIS TIME. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.