WenmarOpen by Wenmar Pro

Service bulletins for the 2015 Mazda Mazda5

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

198 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Bulletins, newest first
09-016-16-3158A2017-02-24. Service bulletin. SEATS. AT PDI OR WHEN NEW VEHICLE IS DELIVERED, SOME CUSTOMERS MAY COMPLAIN ABOUT WRINKLES ON THE LEATHER SEAT CUSHION AND/OR SEAT BACK SURFACE.CUSTOMERS HAVING THIS CONCERN SHOULD HAVE THEIR VEHICLE REPAIRED BY A QUALIFIED UPHOLSTERY REPAIR SPECIALIST USING THE FOLLOWING REPAIR PROCEDURE.THIS SERVICE BULLETIN IS ONLY FOR SUBLET REPAIR. A QUALIFIED UPHOLSTERY REPAIR SPECIALIST IS REQUIRED FOR THIS REPAIR PROCEDURE. PLEASE PRINT A COPY OF THIS BULLETIN FOR THE UPHOLSTERY REPAIR SPECIALIST.
1080M2017-02-23. Service bulletin. ENGINE. IF AN ENGINE ASSEMBLY IS REPLACED AFTER A CATASTROPHIC INTERNAL MECHANICAL FAILURE, CLEAN THE INTAKE MANIFOLD INTERNALLY BEFORE INSTALLING A REPLACEMENT ENGINE ASSEMBLY. IF THE INTAKE MANIFOLD IS NOT CLEANED PROPERLY, THE REPLACEMENT ENGINE MAY FAIL PREMATURELY.METALLIC DEBRIS FROM THE OLD ENGINE (WITH CATASTROPHIC INTERNAL MECHANICAL FAILURE) MAY REST INSIDE THE INTAKE MANIFOLD. WHEN THE NEW ENGINE ASSEMBLY IS INSTALLED, DEBRIS IN THE INTAKE MANIFOLD WILL BE INGESTED INTO THE NEW ENGINE AND CAUSE INTERNAL DAMAGE.CLEAN THE INTAKE MANIFOLD INTERNALLY TO REMOVE ANY DEBRIS FROM OLD ENGINE BEFORE INSTALLING THE NEW REPLACEMENT ENGINE ASSEMBLY.IF THE INTAKE MANIFOLD CANNOT BE PROPERLY CLEANED INTERNALLY, REPLACE IT.
01-016-16-32202017-02-23. Service bulletin. ENGINE. THERE IS A CONCERN THAT SOME WATER PUMPS ARE BEING REPLACED THAT ARE NOT FAULTY, DUE TO SIGNS OF A VERY SMALL COOLANT LEAK FROM THE BLEED HOLE. THIS SERVICE BULLETIN IS TO INFORM YOU ABOUT THE WATER PUMP SEALING MECHA-NISM AND THE CRITERIA IF REPLACEMENT IS NECESSARY OR NOT.
1099M2017-02-22. Service bulletin. ELECTRICAL SYSTEM. WHEN REPROGRAMMING A CONTROL MODULE, ALWAYS USE THE GR-8 BATTERY MANAGEMENT SYSTEM POWER SUPPLY MODE. IF NOT USED, THE CONTROL MODULE REPROGRAMMING MAY FAIL DUE TO A WEAK VEHICLE BATTERY.THE GR-8 BATTERY MANAGEMENT SYSTEM POWER SUPPLY MODE PREVENTS THE VEHICLE BATTERY FROM BEING DISCHARGED. THIS ALLOWS THE IDS TO REPROGRAM A CONTROL MODULE WITHOUT INTERFERENCE FROM A WEAK OR UNDERCHARGED VEHICLE BATTERY. NOTE: CONTROL MODULE DAMAGE MAY OCCUR IF THE GR-8 BATTERY MANAGEMENT SYSTEM POWER SUPPLY MODE IS NOT USED.
1066M2017-02-22. Service bulletin. EXTERIOR LIGHTING. SOME CUSTOMERS MAY COMPLAIN ABOUT IMPROPER OPERATION OF THE AUTO-DIMMING MIRROR. THIS MAY BE CAUSED BY AN OBSTRUCTION OF THE FRONT AND/OR REAR LIGHT SENSOR(S) (E.G. HANGING A PARKING PERMIT FROM THE MIRROR). USE A SOFT CLOTH WITH MILD DETERGENT TO CLEAN THE MIRROR. HARSH DETERGENT MAY DAMAGE THE FRONT AND/OR REAR LIGHT SENSOR(S).
1102M2017-02-21. Service bulletin. ENGINE. WORKSHOP MANUAL EVAP SYSTEM LEAK INSPECTION USING THE M-MDS HAS BEEN DISCONTINUED FOR SOME MODELS. INSTEAD, THE WORKSHOP MANUAL EVAP SYSTEM LEAK INSPECTION USING EVAP LEAK TESTER WILL BE USED TO TROUBLESHOOT EVAP SYSTEM LEAKS.
09-016-16-3158A2017-02-17. Service bulletin. SEATS. AT PDI OR WHEN NEW VEHICLE IS DELIVERED, SOME CUSTOMERS MAY COMPLAIN ABOUT WRINKLES ON THE LEATHER SEAT CUSHION AND/OR SEAT BACK SURFACE.CUSTOMERS HAVING THIS CONCERN SHOULD HAVE THEIR VEHICLE REPAIRED BY A QUALIFIED UPHOLSTERY REPAIR SPECIALIST USING THE FOLLOWING REPAIR PROCEDURE.THIS SERVICE BULLETIN IS ONLY FOR SUBLET REPAIR. A QUALIFIED UPHOLSTERY REPAIR SPECIALIST IS REQUIRED FOR THIS REPAIR PROCEDURE. PLEASE PRINT A COPY OF THIS BULLETIN FOR THE UPHOLSTERY REPAIR SPECIALIST.
1098M2017-02-14. Service bulletin. STRUCTURE. WHEN REMOVING PARTS FROM A VEHICLE, TAKE CAUTION OF THIS SYMBOL "R". FAILING TO REPLACE THE NON-REUSABLE PART MAY CAUSE A SYSTEM FAILURE.
MTI_10312017-02-13. Service bulletin. EQUIPMENT. SOME CUSTOMERS MAY COMPLAIN ABOUT A BLURRY REAR VIEW MONITOR DISPLAY. THIS MAY BE CAUSED BY AN AFTERMARKET ACCESSORY DEVICE
MTI_11112017-02-13. Service bulletin. EQUIPMENT. WHEN INSTALLING A NAVIGATION SD CARD, CONFIRM THAT THE CARD IS UNLOCKED. ALSO, MAZDA DOES NOT RECOMMEND SWAPPING NAVIGATION SYSTEM SD CARDS FROM ONE VEHICLE TO ANOTHER FOR TESTING. IF SWAPPED, THE SD CARD THAT IS INSTALLED INTO THE OTHER VEHICLE BECOMES “LINKED” TO THE VIN OF THAT VEHICLE.
MTI_10342017-02-13. Service bulletin. VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM. THIS ARTICLE PROVIDES HVAC HEATER/DEFROSTER OPERATING TIPS USING MODE SELECTOR DIAL. THIS INCLUDES THE USE OF INTERMEDIATE POSITIONS.
MTI_10322017-02-13. Service bulletin. EQUIPMENT. SOME CUSTOMERS MAY COMPLAIN ABOUT A RATTLE TYPE NOISE COMING FROM THE REAR OF THE VEHICLE WHEN DRIVING ON ROUGH ROADS. THIS MAY BE CAUSED BY A LOOSE SPARE TIRE JACK.
MTI_10312017-02-11. Service bulletin. EQUIPMENT. SOME CUSTOMERS MAY COMPLAIN ABOUT A BLURRY REAR VIEW MONITOR DISPLAY. THIS MAY BE CAUSED BY AN AFTERMARKET ACCESSORY DEVICE.
MTI_11112017-02-11. Service bulletin. EQUIPMENT. WHEN INSTALLING A NAVIGATION SD CARD, CONFIRM THAT THE CARD IS UNLOCKED. ALSO, MAZDA DOES NOT RECOMMEND SWAPPING NAVIGATION SYSTEM SD CARDS FROM ONE VEHICLE TO ANOTHER FOR TESTING. IF SWAPPED, THE SD CARD THAT IS INSTALLED INTO THE OTHER VEHICLE BECOMES “LINKED” TO THE VIN OF THAT VEHICLE.
MTI_10342017-02-10. Service bulletin. VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM:HEATER CORE. THIS ARTICLE PROVIDES HVAC HEATER/DEFROSTER OPERATING TIPS USING MODE SELECTOR DIAL. THIS INCLUDES THE USE OF INTERMEDIATE POSITIONS.
09-016-16-31582017-02-07. Service bulletin. SEATS. AT PDI OR WHEN NEW VEHICLE IS DELIVERED, SOME CUSTOMERS MAY COMPLAIN ABOUT WRINKLES ON THE LEATHER SEAT CUSHION AND/OR SEAT BACK SURFACE.CUSTOMERS HAVING THIS CONCERN SHOULD HAVE THEIR VEHICLE REPAIRED BY A QUALIFIED UPHOLSTERY REPAIR SPECIALIST USING THE FOLLOWING REPAIR PROCEDURE.
02-009-16-31552017-02-07. Service bulletin. STEERING. SOME CUSTOMERS MAY COMPLAIN THAT THE STEERING WHEEL IS OFF CENTER MORE THAN 3° EVEN WHEN DRIVING STRAIGHT ON A FLAT ROAD.
1098M2017-02-07. Service bulletin. STRUCTURE. WHEN REMOVING PARTS FROM A VEHICLE, TAKE CAUTION OF THIS SYMBOL "R". FAILING TO REPLACE THE NON-REUSABLE PART MAY CAUSE A SYSTEM FAILURE.
01-014-16-3208A2016-12-03. Service bulletin. ENGINE. SOME VEHICLES MAY EXPERIENCE A LACK OF ENGINE POWER/ROUGH IDLING AND THE CHECK ENGINE LIGHT ON WITH ONE OR MORE OF THE MISFIRE RELATED DTCS OF P0300:00, P0301:00, P0302:00, P0303:00 AND P0304:00. THIS CONCERN MAY BE CAUSED BY AN INTERNAL FAILURE OF THE IGNITION COIL(S) DUE TO A HIGH DIFFERENCE BETWEEN COLD AND WARM AMBIENT TEMPERATURES. THE PRODUCTION METHOD OF THE IGNITION COIL HAS BEEN CHANGED TO ELIMINATE THIS CONCERN.
SA2342016-12-02. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. IDS UPDATE 101.00 AND 101.02 IS NOW AVAILABLE ON MS3 UNDER THE "IDS/INFOTAINMENT" TAB.
1080M2016-12-01. Service bulletin. ENGINE. IF AN ENGINE ASSEMBLY IS REPLACED AFTER A CATASTROPHIC INTERNAL MECHANICAL FAILURE, CLEAN THE INTAKE MANIFOLD INTERNALLY BEFORE INSTALLING A REPLACEMENT ENGINE ASSEMBLY. IF THE INTAKE MANIFOLD IS NOT CLEANED PROPERLY, THE REPLACEMENT ENGINE MAY FAIL PREMATURELY.METALLIC DEBRIS FROM THE OLD ENGINE (WITH CATASTROPHIC INTERNAL MECHANICAL FAILURE) MAY REST INSIDE THE INTAKE MANIFOLD. WHEN THE NEW ENGINE ASSEMBLY IS INSTALLED, DEBRIS IN THE INTAKE MANIFOLD WILL BE INGESTED INTO THE NEW ENGINE AND CAUSE INTERNAL DAMAGE.CLEAN THE INTAKE MANIFOLD INTERNALLY TO REMOVE ANY DEBRIS FROM OLD ENGINE BEFORE INSTALLING THE NEW REPLACEMENT ENGINE ASSEMBLY.IF THE INTAKE MANIFOLD CANNOT BE PROPERLY CLEANED INTERNALLY, REPLACE IT
09-010/162016-07-14. Service bulletin. STRUCTURE. STAINS FOUND ON PAINT DURING PDI SOME VEHICLES MAY EXPERIENCE STAINS APPEARING ON THE HOOD, ROOF AND/OR TRUNK OF VEHICLE. THIS CONCERN IS MOST LIKELY TO BE FOUND IN COLD WEATHER AREAS JUST AFTER THE RAPGARD IS REMOVED AT PDI. THIS MAY BE CAUSED BY MOISTURE WHICH HAS BEEN TRAPPED AND CONDENSED BETWEN PAINT AND THE RAPGARD. THESE TYPES OF STAINS CAN BE REMOVED WITH HEAT GUN OR AN INFRARED DRIER. IF YOU ENCOUNTER THIS CONCERN DURING PDI, USE HEAT GUN OR AN INFRARED DRIER TO APPLY HEAT TO THE AFFECTED ARE TO REMOVE STAIN(S).
09-009/162016-07-14. Service bulletin. EQUIPMENT:ELECTRICAL. HANDS-FREE BLUETOOTH MODULE AND/OR TEXT MESSAGING TROUBLESHOOTING PROCEDURE. SOME VEHICLES MAY EXHIBIT BLUETOOTH HANDS-FREE AND/OR TEXT MESSAGING RELATED CONCERNS. TO IMPROVE THEHANDLING OF BLUETOOTH HANDS-FREE AND/OR TEXT MESSAGING CUSTOMER CONCERNS, MAZDA CREATED A SPECIAL SERVICE AND PARTS EXCHANGE PROGRAM AS OF FEBRUARY 2010. CUSTOMERS EXPERIENCING RELATED CONCERNS SHOULD HAVE THEIR VEHICLE AND/OR DEVICE INSPECTED ACCORDING TO THE FOLLOWING PROCEDURE.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.