WenmarOpen by Wenmar Pro

Service bulletins for the 2022 Mazda Mazda3

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

436 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Bulletins, newest first
SSPD8 Dlr Ltr a2026-04-04. Warranty extension. ENGINE. Subject: TSB 01-001/26 Warranty and Parts Kit Update INCLUDES: Warranty Extension Program - Special Service Program (SSP) D8 Check Engine Light ON with DTC P0126:00, 2018-2025 CX-5, 2019-2023 Mazda3, 2019-2022 CX-3, 2018-2021 Mazda6, 2020-2023 CX-30 Dear Mazda Dealer Colleagues, Mazda Motor Corporation has made a change regarding related parts to TSB 01-001/26 which also impacts Warranty Extension Special Service Program (SSPD8). Parts Ordering and Warranty Claims: Effective March 5, 2026 only the related parts kit PYY2-15-SAY can be ordered and claimed for any repair. The two separate parts PYFB-15-169 and PE13-15-296 can no longer be claimed with repaired dates of March 5, 2026 and later. There is no change to the main part, the Plug PYY3-15-SA1. We have updated the TSB 01-001/26 and SSPD8 Repair Procedure and Parts & Warranty Information on Mazda Global Service Support (MGSS) to reflect this change.
SA-014-262026-04-02. Service bulletin. ENGINE. This Service Alert supersedes the previously issued SA(s) and TSB(s) listed below: The changes are noted in Red. SA-035/24 05/31/24 DESCRIPTION There is a concern that some water pumps are being replaced that are not faulty, due to signs of a very small coolant leak from the bleed hole. This Service Alert is to inform you about the water pump sealing mechanism and the criteria if replacement is necessary or not. A mechanical seal (A) is used for the water pump. This mechanical seal can seal coolant (B) by sliding a mating ring (C) against a seal ring (D). When the sliding surface temperature of the mechanical seal is more than 248 °F (120 °C) while driving, a small amount of steam (E) is leaked and bleeds through the bleeding hole (F). After drying, the steam leaves a green coolant deposit near the water pump bleed hole (F). This is a normal condition and does not require water pump replacement. The water pump should only be replaced if there is an accumulation of crystallized coolant near the bleed hole. When you encounter a water pump with coolant seepage marks, decide to replace it or not based on the following criteria using sample photos. NOTE: During the initial period of use*, the sliding surfaces of the seals may not yet be fully settled, which can temporarily increase the amount of leakage. Continued use will allow the surfaces to settle, reducing the leakage. Replacing parts that are already settled with new ones will increase the leakage again until the new parts become conditioned. Therefore, replacement should be avoided in this initial period of use. *As a guideline, this applies to vehicles with less than 1,860 miles (3000 km) of mileage.
09-013-262026-04-02. Service bulletin. ELECTRICAL SYSTEM; STRUCTURE:BODY. DESCRIPTION Some customers may experience one or both of the following symptoms while locking and unlocking the doors works fine using the remote transmitter. Symptom 1: The touch sensor of the front door outer handle does not lock the doors after rain and/or car washing, even though unlocking is possible. Symptom 2: The touch sensor of the front door outer handle does not unlock the doors. Door outer handle touch sensor for locking (1) / unlocking (2) NOTE: If the concern occurs after specific operation as described below, refer to the TSB 09-046/22 (DOOR OUTER HANDLE TOUCH SENSOR DOES NOT LOCK AND UNLOCK AFTER A SPECIFIC OPERATION). 1. [MX-30] After using cabin preconditioning or hazard warning lights for approx.15 minutes. 2. [MAZDA3 and CX-30] After using hazard warning lights for approx. 15 minutes. 3. [MAZDA3, CX-30 and MX-30] When both touch sensors are touched at once. Cause 1 (for Symptom 1): Water may accumulate around the touch sensor in the outer handle, resulting in temporary lower sensitivity of the capacitive sensor. Also, if car wash foam gets inside the outer handle while washing the vehicle, the foam may disturb the touch sensor detection. Mazda is still working on a mass production change for this concern. Cause 2 (for Symptom 2): Improper soldering in the production process may disturb the touch sensor detection. To eliminate this concern, the production process has been modified. Customers having this concern should have their vehicle repaired using the following repair procedure. REPAIR PROCEDURE 1. Verify customer concern. 2. Repair the vehicle depending on the experienced symptom(s). Symptom 1: Follow the "Procedure to waterproof a touch sensor” below to make the touch sensor waterproof. Symptom 2: Replace the front outer handle with a modified one according to the instructions on MGSS. Mazda3 (FRONT OUTER HANDLE REMOVAL/INSTALLATION) CX-30 (FRONT OUTER HANDLE REMOVAL/INSTALLATION) MX-30 (FRONT OUTER HANDLE REMOVAL/INSTALLATION) If both symptoms are experienced: Replace the front outer handle with a modified one and follow the “Procedure to waterproof a touch sensor” below to make the touch sensor waterproof. NOTE: DO NOT repair the other front outer handle for the vehicle if it is not experiencing any problems. 3. Verify the repair by checking if the new outer handle locks/unlocks the door correctly.
01-001-26b2026-04-02. Service bulletin. ENGINE; UNKNOWN OR OTHER. Some customers may experience a check engine light ON with DTC P0126:00 (Thermostat stuck open) and one or more of the following symptoms: Engine takes longer to warm up. Engine temperature gauge fluctuates. Low coolant temperature indicator (blue) light stays on longer or turns on while driving. Poor heater performance, especially at idle. Vehicles with SKYACTIV-G 2.5T are not applicable to this service information. DTC P0126:00 is not required to be present to perform this repair. If the vehicle has not previously had the repair specified in this TSB and is exhibiting any of the listed symptoms, proceed with the repair procedure outlined in this bulletin. If DTC P2B61:00 (Coolant Control Valve Circuit Range/Performance) is present along with DTC P0126:00, this TSB does not apply. Diagnose the symptom and/or stored DTCs according to the procedures in MGSS. If only DTC P0126:00 is present and this TSB has already been completed previously, this bulletin does not apply, diagnose the symptom and/or stored DTCs according to the procedures in MGSS. This concern may be caused if the coolant control valve fail-safe thermostat opens at a temperature lower than the normal temperature due to a deformation of the thermostat diaphragm. To eliminate the concern, the water flow control valve specification has been modified. Affected vehicles will require PCM reprogramming with the Mazda Modular Diagnostic System (M-MDS), using either a) Mazda Diagnostic and Repair Software (MDARS) or b) Mazda Integrated Diagnostic System (IDS) 140.04 or later software.
SSPD8 Repair c2026-03-04. Warranty extension. ENGINE. SSPD8 - Check Engine Light ON with DTC P0126:00 - WARRANTY EXTENSION For certain 2018-2025MY CX-5, 2019-2023MY Mazda3, 2019-2022MY CX-3, 2018-2021MY Mazda6, 2020-2023MY CX-30 that are equipped with the suspected coolant control valve, the warranty coverage for specific repair of the fail-safe thermostat is extended to: 15 years (180 months) or 150,000 miles (240,000 km) whichever comes first, from the original warranty start date. CONDITION OF CONCERN: On certain subject vehicles, the check engine light is illuminated with DTC P0126:00 (Thermostat stuck open) stored in memory and one or more of the following symptoms may occur: - Engine takes longer to warm up. - Engine temperature gauge fluctuates. - Low coolant temperature indicator (blue) light stays on longer or turns on while driving. - Poor heater performance, especially at idle. Mazda Motor Corporation has made a significant repair change to TSB 01-003/25 which also impacts Warranty Extension Special Service Program (SSPD8). Repair Procedure Update: Effective December 8th all repairs applicable to TSB 01-003/25 or SSPD8 must follow the new repair procedure. The repair now replaces the thermostat with a dummy plug for the coolant control valve (CCV) along with a required software update for the PCM. Prior Repairs: Any repairs previously completed with the replacement of the thermostat or coolant control valve assembly does not require a re-repair unless there is a verified failure following the diagnosis in the TSB. It is expected that there will be no further repairs made for this concern once the plug and software update has been completed. Therefore, a return visit for symptoms related to the TSB or SSP must contact the Technical Hotline for assistance. VITALLY IMPORTANT!: There must be a “Software Update” record for the PCM when using MDARS or IDS. • MDARS - If there is no Software Update entry in MDARS or the Collect Diagnostic Information (ODR Update) is not completed (or both), the vehicle will not be considered repaired and the warranty claim will be rejected. • IDS – Vehicles programed with IDS must Collect Diagnostic Data, and that data must be attached to the warranty claim. If the data is not attached to the claim, the vehicle will not be considered repaired and the warranty claim will be rejected, denied or debited. Failure to complete the above will require the vehicle to return to the dealership and be re-repaired at the dealer’s expense with great inconvenience to the Mazda customer. Failure to perform the software update could also potentially damage the engine which would not be covered by warranty and would expose your dealership to the cost of repairs.
SSPD5 Repair b2026-03-04. Warranty extension. ENGINE. SPECIAL SERVICE PROGRAM - SSPD5 - WARRANTY EXTENSION - MULTI-MODEL - VALVE STEM SEALS CLASS ACTION In conjunction with a Class Action Settlement, Mazda Motor Corporation has decided to conduct an extension of the Engine powertrain warranty related to excessive oil consumption. In addition, there is a Reimbursement Program, for limited qualifying out-of-pocket expenses (prior oil changes and additional oil purchased before the normal oil change interval due to oil consumption concerns) on certain CX-9, CX-5, Mazda6, Mazda3, and CX-30 vehicles equipped with a 2.5L turbocharged engine with the affected valve stem seals. For all Mazda dealers, an FAQ document for this Class Action Settlement and all documents for SSPD5 will be available on Mazda Global Service Support (MGSS) on or before May 13, 2024 concurrent with notification to the Settlement Class. Please review this entire communication in regards to updated coverage for Special Service Program SSPD5 and vehicles out of Powertrain Warranty. Parts & Warranty Information and Dealer FAQ’s on Mazda Global Service Support (MGSS) have been updated. • Update August 2025: The Court has clarified that under the settlement agreement, the Mazda Powertrain Limited Warranty Extension includes coverage for 7 years, 84,000 miles for all Powertrain components in the Warranty Booklet under the Powertrain Limited Warranty Parts List (i.e. without restriction to engine issues, oil consumption or valve stem seal issues). • Vehicles are covered only for valve stem seal related repairs for an additional 12,000 miles (96,000 miles total) if the vehicle is presented to a Mazda dealer by October 15, 2025. The overall Mazda Powertrain Limited Warranty Extension (i.e., for all other powertrain warranty repairs) does not apply to this coverage period. • Reimbursement for paid repairs prior to August 2025: Reimbursement will also be provided for any Class Member who was denied Powertrain Limited Warranty coverage and paid out-of-pocket for a qualifying Powertrain Limited Warranty repair during the applicable period of the SSPD5 campaign. The customer will need to go to https://www.mazdavalvestemsealsettlement.com/ to file a claim and contact JND Legal Administration with questions regarding reimbursement. • All Mazda warranty limitations apply to SSPD5 including branded vehicles, W-1, total loss, salvage, rebuilt, etc.. and all other limitations as outlined in the Dealer FAQ’s and Mazda Warranty Policies and Procedures 3.26.
PF-26-012026-03-04. Other. ENGINE. The coolant control valve updated part is now available and supersedes PYFD-15-16ZA. As a result, PYFD-15-16ZA is no longer available. PW5S-15-16Z is supplied with a dummy plug pre-installed. Critical Installation Requirement: When replacing PW5S-15-16Z, the Powertrain Control Module (PCM) must also be updated to the latest software version. Failure to perform the PCM update may result in drivability concerns or diagnostic trouble codes.
01-004-262026-03-03. Service bulletin. ENGINE. This bulletin supersedes the previously issued bulletin(s) listed below. The changes are noted below in Red. 01-007/24 06/20/24 ENGINE OIL LEVEL WARNING LIGHT ON WITH DTC P250F:00 DUE TO LOW ENGINE OIL LEVEL (UPDATED WITH SSPD5 INFORMATION). All Mazda Dealers: Follow the Special Service Program SSPD5 – Valve Stem Seal Class Action for determination if valve stem seals should be replaced. 1. Verify the customer concern following the Special Service Program SSPD5 Repair Procedure. As the repair procedure states in SSPD5, confirm the engine oil is not leaking from the engine. If the customer reports engine oil is low upon arrival at a dealer, replace the valve stem seals following the flow chart for SSPD5. If engine oil is low upon arrival with no customer complaint, check for SSPD5 and if the valve stem seals have not been replaced under prior Warranty, replace the seals. If the valve stem seals have been replaced under a prior Warranty claim, contact Hotline for further instructions. If valve stem seals need to be replaced, replace the valve seals of the exhaust side with improved ones using the special tools called out in the repair procedures below. 2. Top off the engine oil (if needed). NOTE: Engine oil should not be topped off without replacement of the valve stem seals. 3. Verify the repair. NOTE: If unsure what steps to take during a customer visit for oil consumption related to SSPD5, fill out Dealer Recall Help on OneMazda.
SSPD8 Repair b2026-02-03. Warranty extension. ENGINE. SSPD8 - Check Engine Light ON with DTC P0126:00 - WARRANTY EXTENSION For certain 2018-2025MY CX-5, 2019-2023MY Mazda3, 2019-2022MY CX-3, 2018-2021MY Mazda6, 2020-2023MY CX-30 that are equipped with the suspected coolant control valve, the warranty coverage for specific repair of the fail-safe thermostat is extended to: 15 years (180 months) or 150,000 miles (240,000 km) whichever comes first, from the original warranty start date. CONDITION OF CONCERN: On certain subject vehicles, the check engine light is illuminated with DTC P0126:00 (Thermostat stuck open) stored in memory and one or more of the following symptoms may occur: - Engine takes longer to warm up. - Engine temperature gauge fluctuates. - Low coolant temperature indicator (blue) light stays on longer or turns on while driving. - Poor heater performance, especially at idle. Mazda Motor Corporation has made a significant repair change to TSB 01-003/25 which also impacts Warranty Extension Special Service Program (SSPD8). Repair Procedure Update: Effective December 8th all repairs applicable to TSB 01-003/25 or SSPD8 must follow the new repair procedure. The repair now replaces the thermostat with a dummy plug for the coolant control valve (CCV) along with a required software update for the PCM. Prior Repairs: Any repairs previously completed with the replacement of the thermostat or coolant control valve assembly does not require a re-repair unless there is a verified failure following the diagnosis in the TSB. It is expected that there will be no further repairs made for this concern once the plug and software update has been completed. Therefore, a return visit for symptoms related to the TSB or SSP must contact the Technical Hotline for assistance. VITALLY IMPORTANT!: There must be a “Software Update” record for the PCM when using MDARS or IDS. • MDARS - If there is no Software Update entry in MDARS or the Collect Diagnostic Information (ODR Update) is not completed (or both), the vehicle will not be considered repaired and the warranty claim will be rejected. • IDS – Vehicles programed with IDS must Collect Diagnostic Data, and that data must be attached to the warranty claim. If the data is not attached to the claim, the vehicle will not be considered repaired and the warranty claim will be rejected, denied or debited. Failure to complete the above will require the vehicle to return to the dealership and be re-repaired at the dealer’s expense with great inconvenience to the Mazda customer. Failure to perform the software update could also potentially damage the engine which would not be covered by warranty and would expose your dealership to the cost of repairs.
SSPD8 Parts and Warr a2026-02-03. Warranty extension. ENGINE. SSPD8 - Check Engine Light ON with DTC P0126:00 - WARRANTY EXTENSION For certain 2018-2025MY CX-5, 2019-2023MY Mazda3, 2019-2022MY CX-3, 2018-2021MY Mazda6, 2020-2023MY CX-30 that are equipped with the suspected coolant control valve, the warranty coverage for specific repair of the fail-safe thermostat is extended to: 15 years (180 months) or 150,000 miles (240,000 km) whichever comes first, from the original warranty start date. CONDITION OF CONCERN: On certain subject vehicles, the check engine light is illuminated with DTC P0126:00 (Thermostat stuck open) stored in memory and one or more of the following symptoms may occur: - Engine takes longer to warm up. - Engine temperature gauge fluctuates. - Low coolant temperature indicator (blue) light stays on longer or turns on while driving. - Poor heater performance, especially at idle. Mazda Motor Corporation has made a significant repair change to TSB 01-003/25 which also impacts Warranty Extension Special Service Program (SSPD8). Repair Procedure Update: Effective December 8th all repairs applicable to TSB 01-003/25 or SSPD8 must follow the new repair procedure. The repair now replaces the thermostat with a dummy plug for the coolant control valve (CCV) along with a required software update for the PCM. Prior Repairs: Any repairs previously completed with the replacement of the thermostat or coolant control valve assembly does not require a re-repair unless there is a verified failure following the diagnosis in the TSB. It is expected that there will be no further repairs made for this concern once the plug and software update has been completed. Therefore, a return visit for symptoms related to the TSB or SSP must contact the Technical Hotline for assistance. VITALLY IMPORTANT!: There must be a “Software Update” record for the PCM when using MDARS or IDS. • MDARS - If there is no Software Update entry in MDARS or the Collect Diagnostic Information (ODR Update) is not completed (or both), the vehicle will not be considered repaired and the warranty claim will be rejected. • IDS – Vehicles programed with IDS must Collect Diagnostic Data, and that data must be attached to the warranty claim. If the data is not attached to the claim, the vehicle will not be considered repaired and the warranty claim will be rejected, denied or debited. Failure to complete the above will require the vehicle to return to the dealership and be re-repaired at the dealer’s expense with great inconvenience to the Mazda customer. Failure to perform the software update could also potentially damage the engine which would not be covered by warranty and would expose your dealership to the cost of repairs.
SA-005-262026-02-03. Service bulletin. UNKNOWN OR OTHER. There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method • B. Auxiliary Key Code Cut Method 2019 and newer models require a 10-digit key code to accurately cut keys • 5-digit codes CANNOT be provided for 2019 and newer vehicles (the traditional 5-digit code from the key tag or driver's door lock cylinder is not sufficient and will not be issued for key cutting on these models). • Only Mazda-approved key cutting machines can process these 10-digit codes. • Many older key machines do not support 10-digit codes and cannot be updated to do so. In these cases, dealers will need to purchase one of the newer Mazda-approved key cutting machines capable of handling this requirement. • For a list of current Mazda-approved machines and purchasing options, refer to the Mazda Dealer Equipment Program or view the current Mazda approved key machines below.
SA-001-262026-02-03. Service bulletin. UNKNOWN OR OTHER. Some customers may report an odor or water in the HVAC system and upon inspection, the cabin air filter may be found to be wet.
09-001-262026-02-03. Service bulletin. SEATS. There are wrinkles on the leather seat cushion and/or seat back surface at PDI, when new vehicle is delivered, or when new upholstery is installed under Warranty repair. NOTE: This repair is not a permanent fix, it is meant to make new seats look their best when the vehicle is first presented to the customer. Wrinkles may not be completely removed after the repair is completed. Leather is a natural material and may develop some wrinkles due to aging and wear during normal usage.
01-001-26a2026-02-03. Service bulletin. ENGINE. Some customers may experience a check engine light ON with DTC P0126:00 (Thermostat stuck open) and one or more of the following symptoms: Engine takes longer to warm up. • Engine temperature gauge fluctuates. • Low coolant temperature indicator (blue) light stays on longer or turns on while driving. • Poor heater performance, especially at idle. • This concern may be caused if the coolant control valve fail-safe thermostat opens at a temperature lower than the normal temperature due to a deformation of the thermostat diaphragm. To eliminate the concern, the water flow control valve specification has been modified.
01-001-262026-02-03. Service bulletin. ENGINE. Some customers may experience a check engine light ON with DTC P0126:00 (Thermostat stuck open) and one or more of the following symptoms: Engine takes longer to warm up. • Engine temperature gauge fluctuates. • Low coolant temperature indicator (blue) light stays on longer or turns on while driving. • Poor heater performance, especially at idle. • This concern may be caused if the coolant control valve fail-safe thermostat opens at a temperature lower than the normal temperature due to a deformation of the thermostat diaphragm. To eliminate the concern, the water flow control valve specification has been modified.
SSPD8a Repair2026-01-06. Warranty extension. ENGINE. SSPD8 - Check Engine Light ON with DTC P0126:00 - WARRANTY EXTENSION For certain 2018-2025MY CX-5, 2019-2023MY Mazda3, 2019-2022MY CX-3, 2018-2021MY Mazda6, 2020-2023MY CX-30 that are equipped with the suspected coolant control valve, the warranty coverage for specific repair of the fail-safe thermostat is extended to: 15 years (180 months) or 150,000 miles (240,000 km) whichever comes first, from the original warranty start date. CONDITION OF CONCERN: On certain subject vehicles, the check engine light is illuminated with DTC P0126:00 (Thermostat stuck open) stored in memory and one or more of the following symptoms may occur: - Engine takes longer to warm up. - Engine temperature gauge fluctuates. - Low coolant temperature indicator (blue) light stays on longer or turns on while driving. - Poor heater performance, especially at idle. Mazda Motor Corporation has made a significant repair change to TSB 01-003/25 which also impacts Warranty Extension Special Service Program (SSPD8). Repair Procedure Update: Effective December 8th all repairs applicable to TSB 01-003/25 or SSPD8 must follow the new repair procedure. The repair now replaces the thermostat with a dummy plug for the coolant control valve (CCV) along with a required software update for the PCM. Prior Repairs: Any repairs previously completed with the replacement of the thermostat or coolant control valve assembly does not require a re-repair unless there is a verified failure following the diagnosis in the TSB. It is expected that there will be no further repairs made for this concern once the plug and software update has been completed. Therefore, a return visit for symptoms related to the TSB or SSP must contact the Technical Hotline for assistance. VITALLY IMPORTANT!: There must be a “Software Update” record for the PCM when using MDARS or IDS. • MDARS - If there is no Software Update entry in MDARS or the Collect Diagnostic Information (ODR Update) is not completed (or both), the vehicle will not be considered repaired and the warranty claim will be rejected. • IDS – Vehicles programed with IDS must Collect Diagnostic Data, and that data must be attached to the warranty claim. If the data is not attached to the claim, the vehicle will not be considered repaired and the warranty claim will be rejected, denied or debited. Failure to complete the above will require the vehicle to return to the dealership and be re-repaired at the dealer’s expense with great inconvenience to the Mazda customer. Failure to perform the software update could also potentially damage the engine which would not be covered by warranty and would expose your dealership to the cost of repairs.
SSPD8 Repair2026-01-06. Warranty extension. ENGINE. SSPD8 - Check Engine Light ON with DTC P0126:00 - WARRANTY EXTENSION For certain 2018-2025MY CX-5, 2019-2023MY Mazda3, 2019-2022MY CX-3, 2018-2021MY Mazda6, 2020-2023MY CX-30 that are equipped with the suspected coolant control valve, the warranty coverage for specific repair of the fail-safe thermostat is extended to: 15 years (180 months) or 150,000 miles (240,000 km) whichever comes first, from the original warranty start date. CONDITION OF CONCERN: On certain subject vehicles, the check engine light is illuminated with DTC P0126:00 (Thermostat stuck open) stored in memory and one or more of the following symptoms may occur: - Engine takes longer to warm up. - Engine temperature gauge fluctuates. - Low coolant temperature indicator (blue) light stays on longer or turns on while driving. - Poor heater performance, especially at idle. Mazda Motor Corporation has made a significant repair change to TSB 01-003/25 which also impacts Warranty Extension Special Service Program (SSPD8). Repair Procedure Update: Effective December 8th all repairs applicable to TSB 01-003/25 or SSPD8 must follow the new repair procedure. The repair now replaces the thermostat with a dummy plug for the coolant control valve (CCV) along with a required software update for the PCM. Prior Repairs: Any repairs previously completed with the replacement of the thermostat or coolant control valve assembly does not require a re-repair unless there is a verified failure following the diagnosis in the TSB. It is expected that there will be no further repairs made for this concern once the plug and software update has been completed. Therefore, a return visit for symptoms related to the TSB or SSP must contact the Technical Hotline for assistance. VITALLY IMPORTANT!: There must be a “Software Update” record for the PCM when using MDARS or IDS. • MDARS - If there is no Software Update entry in MDARS or the Collect Diagnostic Information (ODR Update) is not completed (or both), the vehicle will not be considered repaired and the warranty claim will be rejected. • IDS – Vehicles programed with IDS must Collect Diagnostic Data, and that data must be attached to the warranty claim. If the data is not attached to the claim, the vehicle will not be considered repaired and the warranty claim will be rejected, denied or debited. Failure to complete the above will require the vehicle to return to the dealership and be re-repaired at the dealer’s expense with great inconvenience to the Mazda customer. Failure to perform the software update could also potentially damage the engine which would not be covered by warranty and would expose your dealership to the cost of repairs.
SSPD8 Parts and Warr2026-01-06. Warranty extension. ENGINE. SSPD8 - Check Engine Light ON with DTC P0126:00 - WARRANTY EXTENSION For certain 2018-2025MY CX-5, 2019-2023MY Mazda3, 2019-2022MY CX-3, 2018-2021MY Mazda6, 2020-2023MY CX-30 that are equipped with the suspected coolant control valve, the warranty coverage for specific repair of the fail-safe thermostat is extended to: 15 years (180 months) or 150,000 miles (240,000 km) whichever comes first, from the original warranty start date. CONDITION OF CONCERN: On certain subject vehicles, the check engine light is illuminated with DTC P0126:00 (Thermostat stuck open) stored in memory and one or more of the following symptoms may occur: - Engine takes longer to warm up. - Engine temperature gauge fluctuates. - Low coolant temperature indicator (blue) light stays on longer or turns on while driving. - Poor heater performance, especially at idle. Mazda Motor Corporation has made a significant repair change to TSB 01-003/25 which also impacts Warranty Extension Special Service Program (SSPD8). Repair Procedure Update: Effective December 8th all repairs applicable to TSB 01-003/25 or SSPD8 must follow the new repair procedure. The repair now replaces the thermostat with a dummy plug for the coolant control valve (CCV) along with a required software update for the PCM. Prior Repairs: Any repairs previously completed with the replacement of the thermostat or coolant control valve assembly does not require a re-repair unless there is a verified failure following the diagnosis in the TSB. It is expected that there will be no further repairs made for this concern once the plug and software update has been completed. Therefore, a return visit for symptoms related to the TSB or SSP must contact the Technical Hotline for assistance. VITALLY IMPORTANT!: There must be a “Software Update” record for the PCM when using MDARS or IDS. • MDARS - If there is no Software Update entry in MDARS or the Collect Diagnostic Information (ODR Update) is not completed (or both), the vehicle will not be considered repaired and the warranty claim will be rejected. • IDS – Vehicles programed with IDS must Collect Diagnostic Data, and that data must be attached to the warranty claim. If the data is not attached to the claim, the vehicle will not be considered repaired and the warranty claim will be rejected, denied or debited. Failure to complete the above will require the vehicle to return to the dealership and be re-repaired at the dealer’s expense with great inconvenience to the Mazda customer. Failure to perform the software update could also potentially damage the engine which would not be covered by warranty and would expose your dealership to the cost of repairs.
SSPD8 Dlr Ltr2026-01-06. Warranty extension. ENGINE. SSPD8 - Check Engine Light ON with DTC P0126:00 - WARRANTY EXTENSION For certain 2018-2025MY CX-5, 2019-2023MY Mazda3, 2019-2022MY CX-3, 2018-2021MY Mazda6, 2020-2023MY CX-30 that are equipped with the suspected coolant control valve, the warranty coverage for specific repair of the fail-safe thermostat is extended to: 15 years (180 months) or 150,000 miles (240,000 km) whichever comes first, from the original warranty start date. CONDITION OF CONCERN: On certain subject vehicles, the check engine light is illuminated with DTC P0126:00 (Thermostat stuck open) stored in memory and one or more of the following symptoms may occur: - Engine takes longer to warm up. - Engine temperature gauge fluctuates. - Low coolant temperature indicator (blue) light stays on longer or turns on while driving. - Poor heater performance, especially at idle. Mazda Motor Corporation has made a significant repair change to TSB 01-003/25 which also impacts Warranty Extension Special Service Program (SSPD8). Repair Procedure Update: Effective December 8th all repairs applicable to TSB 01-003/25 or SSPD8 must follow the new repair procedure. The repair now replaces the thermostat with a dummy plug for the coolant control valve (CCV) along with a required software update for the PCM. Prior Repairs: Any repairs previously completed with the replacement of the thermostat or coolant control valve assembly does not require a re-repair unless there is a verified failure following the diagnosis in the TSB. It is expected that there will be no further repairs made for this concern once the plug and software update has been completed. Therefore, a return visit for symptoms related to the TSB or SSP must contact the Technical Hotline for assistance. VITALLY IMPORTANT!: There must be a “Software Update” record for the PCM when using MDARS or IDS. • MDARS - If there is no Software Update entry in MDARS or the Collect Diagnostic Information (ODR Update) is not completed (or both), the vehicle will not be considered repaired and the warranty claim will be rejected. • IDS – Vehicles programed with IDS must Collect Diagnostic Data, and that data must be attached to the warranty claim. If the data is not attached to the claim, the vehicle will not be considered repaired and the warranty claim will be rejected, denied or debited. Failure to complete the above will require the vehicle to return to the dealership and be re-repaired at the dealer’s expense with great inconvenience to the Mazda customer. Failure to perform the software update could also potentially damage the engine which would not be covered by warranty and would expose your dealership to the cost of repairs.
SA-061-252026-01-04. Service bulletin. ELECTRICAL SYSTEM. If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.
SA-023-25c2026-01-04. Service bulletin. ENGINE; EXTERIOR LIGHTING; ELECTRICAL SYSTEM. Some customers may complain about any of the following: 1. Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote function(s) inoperative. Engine Start / Stop • Door Lock / Unlock • Lights ON / OFF • Climate Control • 3. MAZDA CONNECT connected vehicle reception strength icon shows "X" or " ". Page
SA-017-25d2026-01-03. Service bulletin. UNKNOWN OR OTHER; ELECTRICAL SYSTEM. Mazda Connect Services - Frequently Asked Questions (FAQ)
09-045-252026-01-03. Service bulletin. STRUCTURE:BODY. Some customers may experience that the fuel lid and charge lid do not lock or unlock during door lock/unlock operation. This is caused by: Improper dimensional accuracy of the lid actuator lock mechanism Incomplete control logic in the R-ESU software To eliminate this concern: The mold design of the lid actuator was modified. The control software of the R-ESU was revised.
07-004-25a2026-01-03. Service bulletin. UNKNOWN OR OTHER. A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. This odor is the result of mold growth in the A/C evaporator/cooling unit which is caused by condensation, dust, and pollen within the cooling unit. This condition is usually worse during high humidity conditions. “Mazda Air Cooling Coil Coating” is available to encapsulate the mold to reduce odors. If the product is properly applied, it can effectively reduce the musty/mildew odor for up to three years. NOTE: See parts information for Mazda Air Cooling Coil Coating and Kit part numbers.
01-003-25b2026-01-03. Service bulletin. ENGINE. Some customers may experience a check engine light ON with DTC P0126:00 (Thermostat stuck open) and one or more of the following symptoms: Engine takes longer to warm up. • Engine temperature gauge fluctuates. • Low coolant temperature indicator (blue) light stays on longer or turns on while driving. • Poor heater performance, especially at idle. • This concern may be caused if the coolant control valve fail-safe thermostat opens at a temperature lower than the normal temperature due to a deformation of the thermostat diaphragm. To eliminate the concern, the water flow control valve specification has been modified.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.