Service bulletins for the 2018 Mazda Mazda3
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
462 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
Only bulletins with component: Engine are shown. Show all
| 01-012-18-3474 | 2018-07-02. Service bulletin. ENGINE. Some vehicles may experience the CHECK ENGINE LIGHT ON with DTC P2610 and P2507 stored inmemory after engine start and room fuse 15A (A) removed. P2610:00: Instrument cluster internal engine off timer performance problem P2507:00: PCM battery voltage low input. As a past malfunction, the customer will not notice it (no warning light illuminated), but the DTC may be found during a vehicle service. P2507 in this situation is only applicable on 2016 and later models. This is caused by the engine being started 3 or more times after a short duration of engine off (less than 15 seconds) with the room fused removed. NOTE: The odometer will display "F0-002" during transport mode (room fuse 15A removed). Transport mode is canceled when room fuse 15A is installed or the vehicle odometer is more than 12.4mi (20km). Vehicles in dealer inventory with this concern should be repaired using the following repair procedure. |
|---|---|
| 05-004-18-3466 | 2018-05-14. Service bulletin. ENGINE AND ENGINE COOLING. Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). P0842:00 - Oil pressure switch No. 1 (oil pressure switch B) stuck on P0847:00 - Oil pressure switch No. 2 (oil pressure switch A) stuck on P0872:00 - Oil pressure switch No. 3 (oil pressure switch A) stuck on P0877:00 - Oil pressure switch No. 4 (oil pressure switch B) stuck on P0780:00 - Gear shifting malfunction P1738:00 Automatic transaxle internal malfunction This is caused by the oil pressure switch A and/or B at the control valve body temporarily or permanently getting stuck due to contamination entering the passage. To correct the problem, some mass production changes have been implemented to reduce contamination and improve the DTC diagnostic logic. NOTE: If the vehicle also has a delayed engagement concern, this TSB is not applicable. Refer to MGSS online for proper diagnosis and repair procedure. |
| 04-003-18-3455 | 2018-05-14. Service bulletin. ENGINE AND ENGINE COOLING. Some customers may report a slight clunk/bang/buzz noise or jolt from the front of the vehicle. This concern will most likely occur during the vehicles first forward movement after starting the engine. This is a normal operating noise of the Anti-Lock Brake System (ABS). Do not attempt any repairs. If you encounter a customer complaint for this concern, explain that the noise comes from the ABS/TCS/DSC "Malfunction Detection Function" initial check and that there is no problem. This initial check is a necessary function to ensure the normal operation of the ABS/TCS/DSC system. It occurs when the vehicles first moves forward under the following conditions. NOTE: Some customers may describe that the noise does not occur all the time. It does occur all the time, but the sound is more likely to be heard on a slow start and not on a quick start (quick acceleration) when engine noise is louder. |
| 01-005-18-3415 | 2018-05-07. Service bulletin. FUEL SYSTEM, GASOLINE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. Some vehicles may experience a rough idle with the check engine light on and DTC P0015 / P0524 stored in memory. P0015:00 - Exhaust CMP timing over-retarded P0524:00 - Engine oil pressure too low This is caused by a drop in engine oil pressure due to a piece of foreign object stuck on the oil pump pressure relief valve or oil control valve (OCV). The temporary entry of the foreign object triggers a check engine light on, but rough idle will not be produced until a later time. |
| 01-006-18-3429 | 2018-04-23. Service bulletin. ENGINE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. When the engine is started for the first time after parking the vehicle overnight in cold conditions (below 32 degrees Fahrenheit / 0 degrees Celsius), some vehicles may exhibit a rough idle and/or the check engine light on with any of the following DTC(s) stored in memory. P0300 - Random misfire detected P0301 - Cylinder No.1 misfire detected P0302 - Cylinder No.2 misfire detected P0303 - Cylinder No.3 misfire detected P0304 - Cylinder No.4 misfire detected. This may be caused by frozen water accumulated in the main silencer, restricting exhaust flow. |
| MT-021-17 | 2018-02-26. Service bulletin. ENGINE; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. Some vehicles may experience the Check Engine Light ON with DTC P0171 (Fuel Trim too Lean) and possibly DTCs P030X (Misfire). Vehicles having this concern should use the following Inspection/Repair procedure. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.