WenmarOpen by Wenmar Pro

Service bulletins for the 2013 Mazda Mazda3

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

504 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Engine are shown. Show all

Bulletins, newest first
01-011-20-37342020-09-01. Service bulletin. ENGINE AND ENGINE COOLING. Some customers may complain about an unusual noise coming from the engine compartment for about 20 seconds after a cold engine start. This noise is a normal engine operation for improved exhaust gas emissions. The noise does not indicate a malfunction. ACCELERATED WARM-UP SYSTEM (AWS): All SKYACTIV-G engines adopt AWS to reduce exhaust gas emissions immediately after a cold engine start. AWS increases the engine idling speed and retards the ignition timing for about 20 seconds after the cold engine start to quickly warm up the catalytic converter. The customer may identify the engine sound during the AWS operation as a unusual noise.
05-003-20-37252020-08-04. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; POWER TRAIN; EQUIPMENT; ENGINE. Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). This is caused by the oil pressure switch A and/or B at the control valve body temporarily or permanently getting stuck due to contamination entering the passage. To correct the problem, some mass production changes have been implemented to reduce contamination and improve the DTC diagnostic logic.
00-001-20-36892020-04-03. Service bulletin. SERVICE BRAKES, HYDRAULIC; POWER TRAIN; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; ENGINE AND ENGINE COOLING. Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
SA-009-202020-01-30. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING; STRUCTURE. LACK OF POWER UNDER HEAVY LOAD WITH NO WARNING LIGHTS OR DTCS: Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system.
SA-053-192019-12-21. Service bulletin. ENGINE AND ENGINE COOLING; POWER TRAIN. GUIDE LINES AND PHOTOS TO DETERMINE IF FLUID/OIL SEEPAGE OR LEAK IS SEVERE ENOUGH TO REQUIRE WARRANTY REPAIR OR TO CLEAN AND MONITOR. Some customer's might state that they notice fluid or oil leaking/dripping on the ground when the vehicle is parked. For this concern, inspect the vehicle for any trace of a fluid or oil leak and use the following examples as a guide to determine if it is severe enough to require a repair, or just to clean the area and monitor it at the next service.
MT-002-192019-12-20. Service bulletin. ENGINE AND ENGINE COOLING; EQUIPMENT. If an engine assembly is replaced after a catastrophic internal mechanical failure, clean the intake manifold internally before installing a replacement engine assembly. If the intake manifold is not cleaned properly, the replacement engine may fail prematurely. Metallic debris from the old engine (with catastrophic internal mechanical failure) may rest inside the intake manifold. When the new engine assembly is installed, debris in the intake manifold will be ingested into the new engine and cause internal damage.
01-022-19-36572019-12-20. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT; ENGINE AND ENGINE COOLING. There is a concern that some water pumps are being replaced that are not faulty, due to signs of a very small coolant leak from the bleed hole. This Service Bulletin is to inform you about the water pump sealing mechanism and the criteria if replacement is necessary or not.
MT-003-192019-10-30. Service bulletin. ENGINE AND ENGINE COOLING. Some customers may complain about high engine oil consumption. Before attempting any repairs, verify the complaint by using the guideline below to determine if an engine repair is necessary:
MT-002-192019-10-04. Service bulletin. ENGINE AND ENGINE COOLING; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE. If an engine assembly is replaced after a catastrophic internal mechanical failure, clean the intake manifold internally before installing a replacement engine assembly. If the intake manifold is not cleaned properly, the replacement engine may fail prematurely. Metallic debris from the old engine (with catastrophic internal mechanical failure) may rest inside the intake manifold. When the new engine assembly is installed, debris in the intake manifold will be ingested into the new engine and cause internal damage.
SA-040-192019-09-23. Service bulletin. STRUCTURE:BODY:HOOD; ENGINE AND ENGINE COOLING. Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system.
01-016-19-36272019-08-30. Service bulletin. ENGINE AND ENGINE COOLING. Some vehicles may experience a rough idle with the check engine light on and DTC P0015 / P0524 stored in memory. P0015:00 - Exhaust CMP timing over-retarded. P0524:00 - Engine oil pressure too low. This is caused by a drop in engine oil pressure due to a piece of foreign object stuck on the oil pump pressure relief valve or oil control valve (OCV). The temporary entry of the foreign object triggers a check engine light on, but rough idle will not be produced until a later time.
01-012-19-36122019-08-01. Service bulletin. ENGINE AND ENGINE COOLING. Some vehicles may experience the Check Engine Light ON with DTC P0300:00, P0301:00, P0302:00, P0303:00 and/or P0304:00 stored in memory. P0300:00: Random misfire detected, P0301:00: Cylinder No.1 misfire detected, P0302:00: Cylinder No.2 misfire detected, P0303:00: Cylinder No.3 misfire detected, P0304:00: Cylinder No.4 misfire detected. Carbon may be deposited around the intake valves, resulting in unstable engine combustion and misfiring during the accelerated warm-up system (AWS) operation.
00-003-19-35832019-03-21. Service bulletin. FUEL SYSTEM, DIESEL:STORAGE:TANK ASSEMBLY; FUEL SYSTEM, GASOLINE; ENGINE AND ENGINE COOLING; EQUIPMENT. In support of the new MRT distribution, Mazda will ship to dealers a new Dual Purpose Diagnostic Leak Detector beginning March, 2019. Training videos will be posted to MGSS shortly and Workshop Manual procedures will be revised gradually.
01-005-19-35482019-02-19. Service bulletin. ENGINE AND ENGINE COOLING. Some vehicles may exhibit the check engine light on with DTC P0456 stored in the PCM memory. P0456: EVAP system leak detected (very small leak). The concern is most likely the result of the customer not getting the fuel cap completely closed after fueling the vehicle. This causes a small fuel vapor leak and turns DTC P0456 on.
01-004-19-35582019-02-19. Service bulletin. ENGINE AND ENGINE COOLING. On some vehicles, a sulfur smell or 'rotten egg' odor may be noticed coming from the exhaust system. The odor is usually noticed after a cold start, fast idle, extended periods of idling and full throttle acceleration. Sulfur smell is not an indication of an engine concern and will not cause reduced driveability or durability of the engine or any of its emission components. The sulfur smell or 'rotten egg' odor is caused by high amounts of sulfur in the gasoline being used in the vehicle. Sulfur is normally eliminated during the refining process, but the EPA regulation of sulfur in gasoline differs from state to state. Vehicles using fuel containing high amounts of sulfur will most likely emit sulfur smell from the exhaust system.When high sulfur fuel is burned, there is a chemical reaction in the catalytic converter causing the sulfur tooxidize. As the vehicle is driven, the oxidizing reaction odor in the converter will decrease with mileage and age.
MT-009-182019-02-19. Service bulletin. ENGINE AND ENGINE COOLING. If an oil pressure inspection is needed on a SKYACTIV-G engine, use the Special Service Tool (SST) set shown below and refer to the instructions on MGSS online: CX-3: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.0] ), MX-3: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.0] ), Mazda6: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.5] ), Mazda3: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5] ), CX-5: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5 (WITHOUT CYLINDER DEACTIVATION)] ). If the Special Service Tool (SST) set above is not available at your dealership, an aftermarket Engine Oil Pressure Gauge can be used along with a locally sourced Oil Pressure Switch Adapter, like the one shown below.
MT-009-182018-12-17. Service bulletin. ENGINE AND ENGINE COOLING. If an oil pressure inspection is needed on a SKYACTIV-G engine, use the Special Service Tool (SST) set shown below and refer to the instructions on MGSS online: CX-3: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.0] ), MX-3: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.0] ), Mazda6: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.5] ), Mazda3: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5] ), CX-5: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5 (WITHOUT CYLINDER DEACTIVATION)] ). If the Special Service Tool (SST) set above is not available at your dealership, an aftermarket Engine Oil Pressure Gauge can be used along with a locally sourced Oil Pressure Switch Adapter, like the one shown below.
01-016-18-35222018-10-09. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. On some vehicles, a sulfur smell or 'rotten egg' odor may be noticed coming from the exhaust system. The odor is usually noticed after a cold start, fast idle, extended periods of idling and full throttle acceleration. Sulfur smell is not an indication of an engine concern and will not cause reduced driveability or durability of the engine or any of its emission components. The sulfur smell or 'rotten egg' odor is caused by high amounts of sulfur in the gasoline being used in the vehicle. Sulfur is normally eliminated during the refining process, but the EPA regulation of sulfur in gasoline differs from state to state. Vehicles using fuel containing high amounts of sulfur will most likely emit sulfur smell from the exhaust system. When high sulfur fuel is burned, there is a chemical reaction in the catalytic converter causing the sulfur to oxidize. As the vehicle is driven, the oxidizing reaction odor in the converter will decrease with mileage and age.
01-013-18-34782018-07-02. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. Some vehicles may exhibit the check engine light on with DTC P0456 stored in the PCM memory. P0456: EVAP system leak detected (very small leak)The concern is most likely the result of the customer not getting the fuel cap completely closed after fuelingthe vehicle. This causes a small fuel vapor leak and turns DTC P0456 on.
05-004-18-34662018-05-14. Service bulletin. ENGINE AND ENGINE COOLING. Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). P0842:00 - Oil pressure switch No. 1 (oil pressure switch B) stuck on P0847:00 - Oil pressure switch No. 2 (oil pressure switch A) stuck on P0872:00 - Oil pressure switch No. 3 (oil pressure switch A) stuck on P0877:00 - Oil pressure switch No. 4 (oil pressure switch B) stuck on P0780:00 - Gear shifting malfunction P1738:00 Automatic transaxle internal malfunction This is caused by the oil pressure switch A and/or B at the control valve body temporarily or permanently getting stuck due to contamination entering the passage. To correct the problem, some mass production changes have been implemented to reduce contamination and improve the DTC diagnostic logic. NOTE: If the vehicle also has a delayed engagement concern, this TSB is not applicable. Refer to MGSS online for proper diagnosis and repair procedure.
04-003-18-34552018-05-14. Service bulletin. ENGINE AND ENGINE COOLING. Some customers may report a slight clunk/bang/buzz noise or jolt from the front of the vehicle. This concern will most likely occur during the vehicles first forward movement after starting the engine. This is a normal operating noise of the Anti-Lock Brake System (ABS). Do not attempt any repairs. If you encounter a customer complaint for this concern, explain that the noise comes from the ABS/TCS/DSC "Malfunction Detection Function" initial check and that there is no problem. This initial check is a necessary function to ensure the normal operation of the ABS/TCS/DSC system. It occurs when the vehicles first moves forward under the following conditions. NOTE: Some customers may describe that the noise does not occur all the time. It does occur all the time, but the sound is more likely to be heard on a slow start and not on a quick start (quick acceleration) when engine noise is louder.
01-005-18-34152018-05-07. Service bulletin. FUEL SYSTEM, GASOLINE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. Some vehicles may experience a rough idle with the check engine light on and DTC P0015 / P0524 stored in memory. P0015:00 - Exhaust CMP timing over-retarded P0524:00 - Engine oil pressure too low This is caused by a drop in engine oil pressure due to a piece of foreign object stuck on the oil pump pressure relief valve or oil control valve (OCV). The temporary entry of the foreign object triggers a check engine light on, but rough idle will not be produced until a later time.
MT-021-172018-02-26. Service bulletin. ENGINE; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. Some vehicles may experience the Check Engine Light ON with DTC P0171 (Fuel Trim too Lean) and possibly DTCs P030X (Misfire). Vehicles having this concern should use the following Inspection/Repair procedure.
SSPA92017-08-25. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL; ENGINE AND ENGINE COOLING. Mazda Motor Corporation is extending the warranty coverage for specific repair of instrument panel on certain 2010-2013 Mazda3 vehicles produced from May 6, 2010 through July 19, 2013. The warranty coverage for instrument panel replacement due to warping or a gap is extended to 7 years (84 months) from the original New Vehicle Limited Warranty (Normal Warranty) start date or April 30, 2018 whichever is later, with no mileage limitation. On certain 2010-2013 Mazda3 vehicles, the instrument panel just above the information display may be warping, generating a gap between the instrument panel and information display, if exposed to heat under high ambient temperature.
SSPA92017-08-25. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL; ENGINE. Mazda Motor Corporation is extending the warranty coverage for specific repair of instrument panel on certain 2010-2013 Mazda3 vehicles produced from May 6, 2010 through July 19, 2013. The warranty coverage for instrument panel replacement due to warping or a gap is extended to 7 years (84 months) from the original New Vehicle Limited Warranty (Normal Warranty) start date or April 30, 2018 whichever is later, with no mileage limitation. On certain 2010-2013 Mazda3 vehicles, the instrument panel just above the information display may be warping, generating a gap between the instrument panel and information display, if exposed to heat under high ambient temperature.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.