Service bulletins for the 2026 Mazda CX-30
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
72 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
| SA-031-26 | 2026-05-05. Service bulletin. STRUCTURE:BODY; UNKNOWN OR OTHER. DESCRIPTION Some vehicles may require the replacement of a damaged VIN plate or vehicle certification label. To obtain a replacement VIN plate (bulkhead-mounted and visible through the lower-left area of the windshield), contact DAG (Dealer Assistance Group) using VIN Plate Request Form available on One Mazda. To obtain a replacement vehicle certification label (located on the Bpillar or front door), contact your assigned DSM (District Service Manager) to place the order. If DSM contact information is not available, refer to the Dealer & Field Contact Directory. |
|---|---|
| SA-029-26 | 2026-05-05. Service bulletin. UNKNOWN OR OTHER; ENGINE; POWER TRAIN; SERVICE BRAKES. This Service Alert supersedes the previously issued SA listed below: The changes are noted in Red. SA-011/24 02/12/24, 06/06/24, 07/29/24 DESCRIPTION Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers. SCHEDULED MAINTENANCE Refer to the applicable Workshop Manual or Owner's Manual for vehicle -specific manufacturer scheduled maintenance. Workshop Manual - Refer to section 00-00 SCHEDULED MAINTENANCE. Owner's Manual - Refer to section 8 Maintenance and Care. b. Note: Please refer to the information below outlining the services not included in Mazda's Factory Scheduled Maintenance: IMPORTANT: Recommending fluid flushes when not necessary can lead to customer confusion and dissatisfaction. Fluid flushing for preventive maintenance purposes is strongly discouraged, unless otherwise specified in a published procedure (Owner’s Manual, Workshop Manual, Technical Service Bulletin, etc.). |
| SA-027-26 | 2026-05-05. Service bulletin. ELECTRICAL SYSTEM. This SA supersedes the previously issued bulletin(s) listed below. The changes are noted below in Red. SA-007/25 10/22/25, 06/02/25 and 02/03/25 DESCRIPTION The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code. NOTE: A Warranty Code is required for warranty claim submission Battery Identification (Mazda batteries have 2 rating types) 1. JIS (Japanese Industrial Standard): JIS codes are six-digit alpha-numeric markings (excluding i-STOP batteries e.g. Q-85, S-95) molded into the top of the battery to identify a battery by the capacity (amps), dimensions, and battery terminal type. Vehicles manufactured in Japan come from the factory with a JIS rated battery. NOTE: Replacement batteries may use a CCA rating. If so, use the CCA rating listed on the battery. 2. CCA (Cold Cranking Amps): CCA ratings are normally located on a sticker affixed to the top of the battery to indicate a battery’s Cold Cranking Amps. CCA rated batteries are supplied with domestically produced vehicles. NOTE: If an incorrect CCA rating is entered into the Mazda DCA-8000, it will result in a false result and invalid Warranty Code from the tester. This will also result in unnecessary replacement of batteries. TEST PROCEDURE 1. Connect the charger clamps to the appropriate battery posts. |
| SA-026-26 | 2026-05-05. Service bulletin. ENGINE. This Service Alert supersedes the previously issued M-Tip(s) listed below. The changes are noted in Red text. MT-002/19 09/30/19 and 12/19/19 DESCRIPTION If an engine assembly is replaced after a catastrophic internal mechanical failure, clean the intake manifold internally before installing a replacement engine assembly. If the intake manifold is not cleaned properly, the replacement engine may fail prematurely. Metallic debris from the old engine (with catastrophic internal mechanical failure) may rest inside the intake manifold. When the new engine assembly is installed, debris in the intake manifold will be ingested into the new engine and cause internal damage. Clean the intake manifold internally to remove any debris from old engine before installing the new replacement engine assembly. If the intake manifold cannot be properly cleaned internally, replace it. |
| SA-028-26 | 2026-05-04. Service bulletin. STEERING; SUSPENSION. DESCRIPTION Some vehicles may exhibit a clicking, popping, tapping or knocking noise from the front when turning left or right and accelerating. NOTE: The noise could occur at different steering wheel angles or power levels. Due to the insulating properties of the suspension and chassis, it can be difficult to determine which driveshaft is at fault by listening from inside the vehicle. See the attached video for an example of an outer CV joint clicking. Repair Procedure: Replace the affected driveshaft after confirming the source of the noise using chassis ears. Both driveshafts may be faulty; verify each side before replacement. |
| SA-012-26b | 2026-05-04. Service bulletin. UNKNOWN OR OTHER; ELECTRICAL SYSTEM. Some customers may experience a message "TCU Malfunction. Have the Vehicle Inspected" in the instrument cluster. Additional symptoms that may occur: Connected Vehicle One Time Passcode (OTP) may fail. • Connected Vehicle Remote functions may fail. • The following DTC's may be stored: B1252:87-8B:TCU - COMMUNICATION ERROR WITH CONNECTIVITY MASTER UNIT (CMU) • U0198:00-03:CMU - COMMUNICATION ERROR WITH EMERGENCY CALL UNIT/TELEMATICS COMMUNICATION UNIT REPAIR PROCEDURE 1. Verify the concern. 2. Check if any of the following DTCs are stored: B1252:87-8B:TCU - COMMUNICATION ERROR WITH CONNECTIVITY MASTER UNIT (CMU) • U0198:00-03:CMU - COMMUNICATION ERROR WITH EMERGENCY CALL UNIT/TELEMATICS COMMUNICATION UNIT Are the following DTCs stored? YES: Proceed to next step. • NO: This service information does not apply. Continue troubleshooting using MGSS. • 3. Check for electrical devices in the vehicle such as a device connected to USB hub, Dash Cam, Insurance Device, FasTrak........ect. Are there any customer electrical devices in the vehicle? YES: Document customer device used, then go to the next step. • NO: Go to the next step. • 4. Clear the DTC's |
| DRW59 Warranty | 2026-04-04. Service campaign. ENGINE. Subject: Notification of Dealer Re-Work (DRW59) – 2026MY CX-30 and 2026MY Mazda3 - Check Engine Light On With DTC P0126:00 Dear Mazda Dealer Colleagues, Mazda Motor Corporation has decided to conduct a Dealer Re-Work on certain 2026MY CX-30 and Mazda3 vehicles. Concern Outline: On certain subject vehicles, the check engine light may illuminate with DTC P0126:00 (Thermostat stuck open) stored due to improper PCM control logic. Repair Outline: Reprogram the PCM with the Mazda Modular Diagnostic System (M-MDS), using Mazda Diagnostic and Repair Software (MDARS) by following TSB 01-006/26 repair instructions. ACTION ITEM - STOP DELIVERY: All affected vehicles in inventory can be sold but not delivered until repaired. There are approximately 17,942 new vehicles in dealer stock and/or in transit to dealers. All affected dealer inventory types with this DRW must be repaired prior to delivery. The number of affected units at your dealership can be seen in Inventory & Sales 2.0 in eMDCS and a VIN list (via an internal MNAO campaign reporting) will also be provided to your District Service Manager by 5pm (Pacific Time) on the date this dealer email is sent. Owner Notification: There is no Owner Notification with this or any Dealer Re-Work. PARTS INFORMATION: There are no parts required for this repair. |
| DRW59 Repair | 2026-04-04. Service campaign. ENGINE. Subject: Notification of Dealer Re-Work (DRW59) – 2026MY CX-30 and 2026MY Mazda3 - Check Engine Light On With DTC P0126:00 Dear Mazda Dealer Colleagues, Mazda Motor Corporation has decided to conduct a Dealer Re-Work on certain 2026MY CX-30 and Mazda3 vehicles. Concern Outline: On certain subject vehicles, the check engine light may illuminate with DTC P0126:00 (Thermostat stuck open) stored due to improper PCM control logic. Repair Outline: Reprogram the PCM with the Mazda Modular Diagnostic System (M-MDS), using Mazda Diagnostic and Repair Software (MDARS) by following TSB 01-006/26 repair instructions. ACTION ITEM - STOP DELIVERY: All affected vehicles in inventory can be sold but not delivered until repaired. There are approximately 17,942 new vehicles in dealer stock and/or in transit to dealers. All affected dealer inventory types with this DRW must be repaired prior to delivery. The number of affected units at your dealership can be seen in Inventory & Sales 2.0 in eMDCS and a VIN list (via an internal MNAO campaign reporting) will also be provided to your District Service Manager by 5pm (Pacific Time) on the date this dealer email is sent. Owner Notification: There is no Owner Notification with this or any Dealer Re-Work. PARTS INFORMATION: There are no parts required for this repair. |
| DRW59 Dlr Ltr | 2026-04-04. Service campaign. ENGINE. Subject: Notification of Dealer Re-Work (DRW59) – 2026MY CX-30 and 2026MY Mazda3 - Check Engine Light On With DTC P0126:00 Dear Mazda Dealer Colleagues, Mazda Motor Corporation has decided to conduct a Dealer Re-Work on certain 2026MY CX-30 and Mazda3 vehicles. Concern Outline: On certain subject vehicles, the check engine light may illuminate with DTC P0126:00 (Thermostat stuck open) stored due to improper PCM control logic. Repair Outline: Reprogram the PCM with the Mazda Modular Diagnostic System (M-MDS), using Mazda Diagnostic and Repair Software (MDARS) by following TSB 01-006/26 repair instructions. ACTION ITEM - STOP DELIVERY: All affected vehicles in inventory can be sold but not delivered until repaired. There are approximately 17,942 new vehicles in dealer stock and/or in transit to dealers. All affected dealer inventory types with this DRW must be repaired prior to delivery. The number of affected units at your dealership can be seen in Inventory & Sales 2.0 in eMDCS and a VIN list (via an internal MNAO campaign reporting) will also be provided to your District Service Manager by 5pm (Pacific Time) on the date this dealer email is sent. Owner Notification: There is no Owner Notification with this or any Dealer Re-Work. PARTS INFORMATION: There are no parts required for this repair. |
| SA-014-26 | 2026-04-02. Service bulletin. ENGINE. This Service Alert supersedes the previously issued SA(s) and TSB(s) listed below: The changes are noted in Red. SA-035/24 05/31/24 DESCRIPTION There is a concern that some water pumps are being replaced that are not faulty, due to signs of a very small coolant leak from the bleed hole. This Service Alert is to inform you about the water pump sealing mechanism and the criteria if replacement is necessary or not. A mechanical seal (A) is used for the water pump. This mechanical seal can seal coolant (B) by sliding a mating ring (C) against a seal ring (D). When the sliding surface temperature of the mechanical seal is more than 248 °F (120 °C) while driving, a small amount of steam (E) is leaked and bleeds through the bleeding hole (F). After drying, the steam leaves a green coolant deposit near the water pump bleed hole (F). This is a normal condition and does not require water pump replacement. The water pump should only be replaced if there is an accumulation of crystallized coolant near the bleed hole. When you encounter a water pump with coolant seepage marks, decide to replace it or not based on the following criteria using sample photos. NOTE: During the initial period of use*, the sliding surfaces of the seals may not yet be fully settled, which can temporarily increase the amount of leakage. Continued use will allow the surfaces to settle, reducing the leakage. Replacing parts that are already settled with new ones will increase the leakage again until the new parts become conditioned. Therefore, replacement should be avoided in this initial period of use. *As a guideline, this applies to vehicles with less than 1,860 miles (3000 km) of mileage. |
| SA-012-26a | 2026-04-02. Service bulletin. UNKNOWN OR OTHER; ELECTRICAL SYSTEM. This Service Alert supersedes the previously issued SA(s) listed below. The changes are noted in Red. SA-012/26 02/26/2026 DESCRIPTION Some customers may experience a message "TCU Malfunction. Have the Vehicle Inspected" in the instrument cluster. Additional symptoms that may occur: Connected Vehicle One Time Passcode (OTP) may fail. Connected Vehicle Remote functions may fail. The following DTC's may be stored: B1252:87-8B:TCU - COMMUNICATION ERROR WITH CONNECTIVITY MASTER UNIT (CMU) U0198:00-03:CMU - COMMUNICATION ERROR WITH EMERGENCY CALL UNIT/TELEMATICS COMMUNICATION UNIT REPAIR PROCEDURE 1. Verify the concern. 2. Check if any of the following DTCs are stored: B1252:87-8B:TCU - COMMUNICATION ERROR WITH CONNECTIVITY MASTER UNIT (CMU) U0198:00-03:CMU - COMMUNICATION ERROR WITH EMERGENCY CALL UNIT/TELEMATICS COMMUNICATION UNIT Are the following DTCs stored? YES: Proceed to next step. NO: This service information does not apply. Continue troubleshooting using MGSS. 3. Check for electrical devices in the vehicle such as a device connected to USB hub, Dash Cam, Insurance Device, FasTrak........ect. Are there any customer electrical devices in the vehicle? YES: Document customer device used, then go to the next step. NO: Go to the next step. 4. Check for a Navi SD Card. Is the vehicle equipped with a Navi SD Card? YES: Replace the Navi SD Card. NO: Go to next step. 5. Complete the Dealer Connected Vehicle Questionnaire. 6. Collect CMU log data. Go to Infotainment/TCU --> Collecting CMU Log Data --> CMU Log Data Retrieval Instructions 7. Collect TCU log data. Go to Infotainment/TCU --> TCU Log Data Retrieval Instructions --> CMU Log Data Retrieval Instructions 8. Contact Hotline for additional assistance. 9. Release the vehicle to the customer. NOTE: This concern is currently under investigation |
| 01-006-26 | 2026-04-02. Service bulletin. ENGINE; UNKNOWN OR OTHER. Some customers may experience the check engine light on with DTC P0126:00 (Thermostat stuck open) stored. This is due to improper PCM logic control. To eliminate the concern, the PCM control software has been modified. REPAIR PROCEDURE 1. Verify the customer concern. 2. Reprogram the ECU with the Mazda Modular Diagnostic System (M-MDS), using Mazda Diagnostic and Repair Software (MDARS). Refer to MDARS ECU Reprogramming Procedure. NOTE: Be sure to submit Diagnostic Information (ODR) data as it is a required item and will be checked during warranty claim submission. Instructions can be found under M-MDS -> MDARS (Uploading Diagnostic Information (ODR) Data). 3. Clear any other DTCs. 4. Verify the repair by starting the engine (READY ON) and confirming there is no CHECK ENGINE light ON or abnormal warning lights present. |
| SA-012-26 | 2026-03-04. Service bulletin. UNKNOWN OR OTHER; ELECTRICAL SYSTEM. This Service Alert supersedes the previously issued SA(s) listed below. The changes are noted in Red. SA-060/25 12/16/25 Some customers may experience a message "TCU Malfunction. Have the Vehicle Inspected" in the instrument cluster. Additional symptoms that may occur: Connected Vehicle One Time Passcode (OTP) may fail. Connected Vehicle Remote functions may fail. The following DTC's may be stored: B1252:87-8B:TCU - COMMUNICATION ERROR WITH CONNECTIVITY MASTER UNIT (CMU) U0198:00-03:CMU - COMMUNICATION ERROR WITH EMERGENCY CALL UNIT/TELEMATICS COMMUNICATION UNIT |
| SA-005-26 | 2026-02-03. Service bulletin. UNKNOWN OR OTHER. There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method • B. Auxiliary Key Code Cut Method 2019 and newer models require a 10-digit key code to accurately cut keys • 5-digit codes CANNOT be provided for 2019 and newer vehicles (the traditional 5-digit code from the key tag or driver's door lock cylinder is not sufficient and will not be issued for key cutting on these models). • Only Mazda-approved key cutting machines can process these 10-digit codes. • Many older key machines do not support 10-digit codes and cannot be updated to do so. In these cases, dealers will need to purchase one of the newer Mazda-approved key cutting machines capable of handling this requirement. • For a list of current Mazda-approved machines and purchasing options, refer to the Mazda Dealer Equipment Program or view the current Mazda approved key machines below. |
| SA-002-26 | 2026-02-03. Service bulletin. WHEELS. Some customers may complain that the tire sidewalls are distorted or "damaged". Sidewall waviness/indentations/undulations are common on radial tires and are more noticeable on tires with taller sidewalls. The higher the tire pressure, the more noticeable the effect will be. Be sure to set the tire pressures at the recommended tire pressure on the vehicle tire label. Sidewall indentations are a cosmetic condition that does not affect the performance of the tires. |
| SA-001-26 | 2026-02-03. Service bulletin. UNKNOWN OR OTHER. Some customers may report an odor or water in the HVAC system and upon inspection, the cabin air filter may be found to be wet. |
| 09-002-26 | 2026-02-03. Service bulletin. STRUCTURE:BODY. On some vehicles, the front door glass run channel may interfere with the rear door garnish. Since the front door glass run channel is not fixed strongly enough to the door, repetition of door operation may result in interference and damage to the rear door rubber seal. 1. When the front door glass is closed, the glass run-channel may be forced to move to the B-pillar side. 2. Under extremely hot climate conditions, the glass run-channel may expand to the B-pillar side. To eliminate this concern, the fixing force and durability of the glass run channel against thermal expansion and vibration has been improved. The shapes of the front and rear glass run channels and the rear garnish lip have been changed to prevent interference. |
| 09-001-26 | 2026-02-03. Service bulletin. SEATS. There are wrinkles on the leather seat cushion and/or seat back surface at PDI, when new vehicle is delivered, or when new upholstery is installed under Warranty repair. NOTE: This repair is not a permanent fix, it is meant to make new seats look their best when the vehicle is first presented to the customer. Wrinkles may not be completely removed after the repair is completed. Leather is a natural material and may develop some wrinkles due to aging and wear during normal usage. |
| SA-061-25 | 2026-01-04. Service bulletin. ELECTRICAL SYSTEM. If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices. |
| SA-023-25c | 2026-01-04. Service bulletin. ENGINE; EXTERIOR LIGHTING; ELECTRICAL SYSTEM. Some customers may complain about any of the following: 1. Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote function(s) inoperative. Engine Start / Stop • Door Lock / Unlock • Lights ON / OFF • Climate Control • 3. MAZDA CONNECT connected vehicle reception strength icon shows "X" or " ". Page |
| SA-062-25 | 2026-01-03. Service bulletin. ENGINE. Some vehicles equipped with a countermeasure Coolant Control Valve (plug in place of the thermostat inside the CCV) may experience a DTC P0126:00. |
| SA-060-25 | 2026-01-03. Service bulletin. ELECTRICAL SYSTEM; UNKNOWN OR OTHER. Some customers may experience a message "TCU Malfunction. Have the Vehicle Inspected" in the instrument cluster. The following DTC's may be stored: B1252:87-8B:TCU - COMMUNICATION ERROR WITH CONNECTIVITY MASTER UNIT (CMU) • U0198:00-03:CMU - COMMUNICATION ERROR WITH EMERGENCY CALL UNIT/TELEMATICS COMMUNICATION UNIT |
| SA-017-25d | 2026-01-03. Service bulletin. UNKNOWN OR OTHER; ELECTRICAL SYSTEM. Mazda Connect Services - Frequently Asked Questions (FAQ) |
| SA-006-25a | 2026-01-03. Service bulletin. UNKNOWN OR OTHER. Customers may report no audio when using the infotainment fader function fully adjusted to the rear. If the customer's vehicle is among the trim levels referenced above it is equipped with a 6-speaker infotainment system and does not include rear door speakers even though there are speaker grills/covers in the rear door panels. MazdaUSA and published vehicle specifications provide the correct information indicating that these trims are equipped with a "6-speaker audio system". This is a normal condition of the "6-speaker audio system" and current Mazda CONNECT fader function. Rear speaker diagnosis is not necessary as they are not equipped. |
| 07-004-25a | 2026-01-03. Service bulletin. UNKNOWN OR OTHER. A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. This odor is the result of mold growth in the A/C evaporator/cooling unit which is caused by condensation, dust, and pollen within the cooling unit. This condition is usually worse during high humidity conditions. “Mazda Air Cooling Coil Coating” is available to encapsulate the mold to reduce odors. If the product is properly applied, it can effectively reduce the musty/mildew odor for up to three years. NOTE: See parts information for Mazda Air Cooling Coil Coating and Kit part numbers. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.