WenmarOpen by Wenmar Pro

Service bulletins for the 2022 Jeep Wagoneer

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

619 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Only bulletins with component: Seats are shown. Show all

Bulletins, newest first
23016232023-04-17. Service bulletin. SEATS. Front Seat Bolster Adjustment Inoperable Customers may comment on the following: ? One or both front seat cushion bolster adjustments are inoperable. This bulletin involves inspecting and possibly adjusting the routing on the seat supply hose.
91001252023-04-17. Service bulletin. SEATS. ELEMENT ASSY HEATER BACK If a WS vehicle, built after 8/24/22, comes with heated seats complain of turning itself off after a few minutes or totally inoperative. Prior to repair, please contact FCA Redacted Content If no response in 15 minutes, please do the following: 1. Note any DTCs stored or active during the vehicle scan. 2. Do not discard heater mat if it has been replaced for any reason. 3. Please help engineering gathering more information, share your findings including a scan report with: FCA Redacted Content
23-003-232023-02-13. Service bulletin. SEATS. Front Seat Vent Inop Front Seats Vent Inoperative. This bulletin involves inspecting and possibly installing a zip tie to secure HVAC vent plenum.
23-001-232023-02-13. Service bulletin. SEATS. Easy Entry and Fold Flat Seats Inoperative This bulletin involves inspection and adjusting the cables for the easy entry/exit and fold flat 2nd row seats. If the cables can not be properly adjusted, then they will need to be replaced. The customer may comment on the following: 2nd row easy entry seat does not operate properly. 2nd row seat fold flat feature does not operate properly.
08-163-22 REV. B2023-01-17. Service bulletin. ELECTRICAL SYSTEM; SEATS; EXTERIOR LIGHTING. Flash: Memory Seat Module (MSM) Updates Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC). ? B1D9B-54 - Seat Horizontal Front Stop Not Learned-Missing Calibration. Customers may experience the following: ? Memory seat do not save on profiles 1 or 2. ? Easy entry/exit functionality is inoperative. This bulletin involves reprogramming the MSM with the latest available software.
08159222023-01-09. Service bulletin. SEATS; ELECTRICAL SYSTEM. Flash: Seat Massage Module (SMM) Updates This bulletin involves reprogramming the SMM with the latest software available. The customer may describe the following: Either one or both massage seats inoperative after the battery was charged from a full drain state.
S22080001482023-01-09. Service bulletin. SEATS. Driver or Passenger Memory Seat Profiles Inoperative, No Easy Entry/Exit Function Available
23045222022-12-12. Service bulletin. SEATS. Second And/Or Third Row Seat Back Covers Loose This bulletin involves inspecting the second and third row seat back panels and re-engaging the retainer J-clips, if necessary. Put the second and third seats into the fold down position. Check the second and third seat backs for large gaps and loose panels.Fig. 1.Loose Panel Area1 - Second And Third Row Seat Back Panels Squeeze seat material to determine if the J-clip becomes exposed around the entire perimeter of the seat back and cover.Seat Backs Seated/Unseated1 - Second And Third Row Seat Back Panel Seated2- Second And Third Row Seat Back Panel UnseatedThis inspection needs to be performed on both the second and third row seat backs. Were there any loose panels or large gaps found in the panels? YES>>>Proceed to Step 1of the Repair Procedure. NO>>>This bulletin has been completed. Use inspection LOP (23-13-29-93) to close the active RSU.
0803822REVA2022-12-12. Service bulletin. ELECTRICAL SYSTEM; SEATS. Flash: Folding Seat Module (FSM) Update This bulletin involves performing a software update and calibration routine on the FSM. The customer may describe the following:The third row seats are misaligned between the right and left either in folded or unfolded positions. If a customer hits an obstacle while folding the third row seats, the seats will reverse (obstacle detection). After five obstacle detections in a row, the seat will lose calibration and the seats will be non-functional.Customers will not be able to fold and unfold the seats from one button press.
23035222022-10-31. Service bulletin. SEATS. Front Row Seat Back Panel Loose This bulletin involves inspecting the front row seat back panels. Check for loose upper and lower panels. If needed the panels will need to be removed and inspected for broken clips and replaced if needed. Check the seat back and upper screen bezel for large gaps and loose panels Verify the Rear Seat Entertainment (RSE) screen bezel installation by checking visually and running hand over the seam checking gap and flushness. Gap should not exceed 1.5mm. Verify with feeler gage if necessary. Cap (bezel) should be flush to back panel. With both thumbs positioned on cap (bezel), simultaneously push upwardsto verify engagement. Cap (bezel) should stay engaged Fig. 1.Upper Seat Back (Bezel) Verify the front seat back panel installation is correct. From the rear seat area place both hands near top of back panel and with fingers slightly engaged into back panel gently pull to verify back panelis correctly installed. There should be no movement in the back panel from this direction. To verify engagement of lower part of back panel, grab rear lower sides and gently pull at same time. Back panel should not show any signs of movement Fig. 2.Seat Back Inspection Were there any loose panels or large gaps found in the upper or lower panels? This inspection needs to be performed on both the driver's and passenger's front seat back. YES>>>Proceed to Step 1 of the Repair Procedure. NO>>>This bulletin has been completed. Use inspection LOP (23-20-34-96) to close the active RSU.
08163222022-10-31. Service bulletin. SEATS; ELECTRICAL SYSTEM. Flash: Memory Seat Module (MSM) Updates This bulletin involves reprogramming the MSM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC). B1D9B-54 - Seat Horizontal Front Stop Not Learned-Missing Calibration. Customers may experience the following:Memory seat do not save on profiles 1 or 2. Easy entry/exit functionality is inoperative.
08159222022-10-31. Service bulletin. SEATS; ELECTRICAL SYSTEM. Flash: Seat Massage Module (SMM) Updates This bulletin involves reprogramming the SMM with the latest software available. The customer may describe the following: Either one or both massage seats inoperative after the battery was charged from a full drain state.
S22080001482022-10-31. Service bulletin. SEATS. Driver or Passenger Memory Seat Profiles Inoperative, No Easy Entry/Exit Function Available
23035222022-10-31. Service bulletin. UNKNOWN OR OTHER; SEATS; EQUIPMENT. Front Row Seat Back Panel Loose This bulletin involves inspecting the front row seat back panels. Check for loose upper and lower panels. If needed the panels will need to be removed and inspected for broken clips and replaced if needed. Check the seat back and upper screen bezel for large gaps and loose panels Verify the Rear Seat Entertainment (RSE) screen bezel installation by checking visually and running hand over the seam checking gap and flushness. Gap should not exceed 1.5mm. Verify with feeler gage if necessary. Cap (bezel) should be flush to back panel. With both thumbs positioned on cap (bezel), simultaneously push upwardsto verify engagement. Cap (bezel) should stay engaged Fig. 1.Upper Seat Back (Bezel) Verify the front seat back panel installation is correct. From the rear seat area place both hands near top of back panel and with fingers slightly engaged into back panel gently pull to verify back panelis correctly installed. There should be no movement in the back panel from this direction. To verify engagement of lower part of back panel, grab rear lower sides and gently pull at same time. Back panel should not show any signs of movement Fig. 2.Seat Back Inspection Were there any loose panels or large gaps found in the upper or lower panels? This inspection needs to be performed on both the driver's and passenger's front seat back. YES>>>Proceed to Step 1 of the Repair Procedure. NO>>>This bulletin has been completed. Use inspection LOP (23-20-34-96) to close the active RSU.
08163222022-10-31. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; SEATS; EXTERIOR LIGHTING; ELECTRICAL SYSTEM. Flash: Memory Seat Module (MSM) Updates This bulletin involves reprogramming the MSM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC). B1D9B-54 - Seat Horizontal Front Stop Not Learned-Missing Calibration. Customers may experience the following:Memory seat do not save on profiles 1 or 2. Easy entry/exit functionality is inoperative.
08159222022-10-31. Service bulletin. ELECTRICAL SYSTEM:12V/24V/48V BATTERY; ELECTRICAL SYSTEM; SEATS; ELECTRICAL SYSTEM:SOFTWARE. Flash: Seat Massage Module (SMM) Updates This bulletin involves reprogramming the SMM with the latest software available. The customer may describe the following: Either one or both massage seats inoperative after the battery was charged from a full drain state.
S22080001482022-10-31. Service bulletin. SEATS. Driver or Passenger Memory Seat Profiles Inoperative, No Easy Entry/Exit Function Available
2300622REVC2022-09-26. Service bulletin. ELECTRICAL SYSTEM; EXTERIOR LIGHTING; SEATS. Heated Seat Calibration Update This bulletin involves updating the HVAC module with the latest software, checkingthe operation of the front heated seats and repairing as required. Customers may comment on the following: Front row heated seats (driver and/or passenger) will not stay on and shutsitself off in less then 15 minutes while occupied. Customers will not experience a Malfunction Indicator Lamp (MIL) illumination or Diagnostic Trouble Codes (DTCs) for this symptom/condition.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.