Service bulletins for the 2024 Jeep Wagoneer S
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
248 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
| S2508000048 REV.A | 2025-08-06. Service bulletin. ELECTRICAL SYSTEM. Charging Status Lights Inoperable (No Illumination) at Charge Port, Vehicle Still Does Charge |
|---|---|
| S2508000058 | 2025-08-06. Service bulletin. ELECTRICAL SYSTEM. Red Turtle Lamp Warning Indicator On, Drive-by-Brake Limp-in-Mode, Propulsion System |
| 08-233-25 | 2025-08-06. Service bulletin. ELECTRICAL SYSTEM. Intermittent Screeching Noise Customer may comment on the following: ● Intermittent screeching noise is coming from inside the cabin when starting or driving the vehicle. This bulletin involves replacing the electronic expansion valve. |
| 105649 | 2025-07-31. Service bulletin. AIR BAGS. MODULE - AIR BAG CONTROL & MODULE - OCCUPANT RESTRAINT |
| 106188 | 2025-07-31. Service bulletin. ELECTRICAL SYSTEM. MODULE - EV CONTROL UNIT |
| 08-222-25 | 2025-07-31. Service bulletin. ELECTRICAL SYSTEM. Integrated Center Stack (ICS) Switches Inoperable Customers may experience one or more of the following: ● The buttons Fig. 1 in the ICS do not function after 15 minutes following a cold ambient temperature start-up and a warning up of the ICS. ● Intermittent functioning of the ICS buttons Fig. 1. This bulletin involves replacing the ICS switch assembly. |
| 23-006-25 REV. B | 2025-07-31. Service bulletin. STRUCTURE:BODY. Windshield Wiper Blade Maintenance Customers may experience one or more of the following: ● Wiper blades that chatter/streak/jump/skip/smear or make noise while traveling across the windshield. |
| 08-223-25 | 2025-07-31. Service bulletin. ELECTRICAL SYSTEM. Hands Free Kick Sensor Replacement ustomer may comment on one or more of the following: ● Drained 12V battery. ● Kick sensor is activating liftgate when there's no person kicking below rear fascia with keyfob on hand. NOTE: The liftgate will only open and close if the keyfob is present. This bulletin involves replacing the Hands Free Power Liftgate Module (Sensor). |
| S2523000068 | 2025-07-23. Service bulletin. STRUCTURE:BODY. Buzz Squeak Rattle (BSR) Noise From Headliner Near Sunroof Opening, Passenger Side Visor, Or B-pillar Area. |
| 08-206-25 REV. B | 2025-07-23. Service bulletin. ELECTRICAL SYSTEM. Flash: Electronic Vehicle Control Unit (EVCU) Updates 11A2 Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● C10FA-00 - Wheel Hub disconnect Actuator Performance Left. ● C10FB-00 - Wheel Hub disconnect Actuator Performance Right. Customers may also comment on the following: ● Wrench icon is illuminated on the Instrument Panel Cluster (IPC This bulletin involves inspecting and possibly reprogramming the EVCU with the latest available software and then performing a Wheel End Disconnect Position Learn routine. |
| S2408000126 REV.A | 2025-07-17. Service bulletin. ELECTRICAL SYSTEM. Diagnostic Trouble Code (DTC) B1A0A-00 Remote Keyless Entry (RKE) FOB 3 Performance |
| S2519000002 REV.A | 2025-07-17. Service bulletin. STEERING. Steering Wheel Off Center. Diagnostic Trouble Code (DTC) C0051-00 Set. |
| S2508000048 | 2025-07-17. Service bulletin. ELECTRICAL SYSTEM. Charging Status Lights Inoperable (No Illumination) at Charge Port, Vehicle Still Does Charge |
| 08-206-25 REV. A | 2025-07-17. Service bulletin. ELECTRICAL SYSTEM. Flash: Electronic Vehicle Control Unit (EVCU) Updates 11A2 Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● C10FA-00 - Wheel Hub disconnect Actuator Performance Left. ● C10FB-00 - Wheel Hub disconnect Actuator Performance Right. Customers may also comment on the following: ● Wrench icon is illuminated on the Instrument Panel Cluster (IPC). This bulletin involves reprogramming the EVCU with the latest available software and performing a Wheel End Disconnect Position Learn routine |
| 08-132-25 REV. A | 2025-07-17. Service bulletin. ELECTRICAL SYSTEM. RSU With Additional Sleep Cycles for HV Battery Integrity Check - Flash: Integrated Dual Charging Module (IDCM) Updates 11A2 Customers may comment on one or more of the following: ● 12 volt battery lamp on the Instrument Panel Cluster (IPC) illuminated due to depleted 12 volt battery. ● Unable to charge at High Voltage Charging station at Level-1, Level-2 or DC Fast Charge. This bulletin involves reprogramming the IDCM, BPCM, MCP A, MCP B and the EVCU with the latest available software and then, if needed, performing a Wheel End Disconnect Position Learn routine |
| 08-129-25 REV. B | 2025-07-17. Service bulletin. ELECTRICAL SYSTEM. Flash: Integrated Dual Charging Module (IDCM) Updates 11A2 Customers may comment on one or more of the following: ● 12 volt battery lamp on the Instrument Panel Cluster (IPC) illuminated due to depleted 12 volt battery. ● Unable to charge at High Voltage Charging station at Level-1, Level-2 or DC Fast Charge. This bulletin involves reprogramming the IDCM, BPCM, MCP A, MCP B and the EVCU with the latest available software and then, if needed, performing a Wheel End Disconnect Position Learn routine. |
| 08-078-25 REV. B | 2025-07-17. Service bulletin. ELECTRICAL SYSTEM. RSU With Additional Sleep Cycles for HV Battery Integrity Check - Flash: Motor Control Processor A (MCP A) Updates 11A2 Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): ● P1626-00 - Park Pawl Motor Stuck. Customers may also comment on one or more of the following: ● Wrench lamp on in the Instrument Panel Cluster (IPC). ● Not able to move the shifter out of Park. ● Vehicle has reduced power. This bulletin also includes the following software enhancement: ● Software enhancement to prevent erroneous fault identification resulting in inverter shutdown |
| 08-077-25 REV. C | 2025-07-17. Service bulletin. ELECTRICAL SYSTEM. RSU With Additional Sleep Cycles for HV Battery Integrity Check - Flash: Motor Control Processor B (MCP B) Updates 11A2 Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): ● P1626-00 - Park Pawl Motor Stuck. Customers may also comment on one or more of the following: ● Wrench lamp on in the Instrument Panel Cluster (IPC). ● Not able to move the shifter out of Park. ● Vehicle has reduced power. This bulletin also includes the following software enhancement: ● Software enhancement to prevent erroneous fault identification resulting in inverter shutdown This bulletin involves reprogramming the IDCM, BPCM, MCP A, MCP B and the EVCU with the latest available software and then, if needed, performing a Wheel End Disconnect Position Learn routine. |
| 08-076-25 REV. C | 2025-07-17. Service bulletin. ELECTRICAL SYSTEM. RSU With Additional Sleep Cycles for HV Battery Integrity Check - Flash: Battery Pack Control Module (BPCM) Updates 11A2 Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0DE6 - Hybrid/EV Battery Pack Cell Voltage Low. NOTE: Active or stored. ● P1DAF - Incompatible Limp In Action Requested. NOTE: Active or stored. ● P1CDE – Hybrid/EV Wakeup Control 2 Output Circuit Short to Ground. ● P1CDA – Hybrid/EV Wakeup Control 1 Output Circuit/Open. ● U00C6 – Lost Communication With AIR Pressure Sensor. ● P0F00 - Hybrid/EV Battery Module 1 Performance. ● P0F01 - Hybrid/EV Battery Module 2 Performance. ● P0F02 - Hybrid/EV Battery Module 3 Performance. ● P0F03 - Hybrid/EV Battery Module 4 Performance. ● P0F04 - Hybrid/EV Battery Module 5 Performance. ● P0F05 - Hybrid/EV Battery Module 6 Performance. ● P0F06 - Hybrid/EV Battery Module 7 Performance. ● P0F07 - Hybrid/EV Battery Module 8 Performance. ● P0F08 - Hybrid/EV Battery Module 9 Performance. ● P0F09 - Hybrid/EV Battery Module 10 Performance. ● P0F0A - Hybrid/EV Battery Module 11 Performance. ● P0F0B - Hybrid/EV Battery Module 12 Performance. ● P0F0C - Hybrid/EV Battery Module 13 Performance. ● P0CA6-00 - Hybrid/EV Battery Charging Current High. NOTE: If the following DTCs are present/active in the BPCM, Battery Pack replacement will be required. Guided Diagnostics will prompt you for the repair action if the diagnostic is present on the vehicle. ● P0ADB-00 - Hybrid/EV Battery Positive Contractor A Control Circuit Low. ● P0AE2-00 - Hybrid/EV Battery Precharge Contactor Circuit Stuck Closed. ● P0AA1-00 - Hybrid/EV Battery Positive Contactor "A" Stuck Closed. ● P0FF8-00 - Hybrid/EV Battery Precharge Contactor Circuit "B" Stuck Closed. Customers may also comment on one or more of the following: ● Wrench icon is illuminated on the Instrument Panel Cluster (IPC). ● Vehicle will not enter Drive Ready Mode. This bulletin also includes the following software enhancement: ● Bootloader update to prevent battery disconnect unit damage. ● Improvements in detecting pre-existing battery disconnect unit damage. ● Charging related enhancements that may lead to DTC P0CA6 falsely setting. This bulletin involves reprogramming the IDCM, BPCM, MCP A, MCP B and the EVCU with the latest available software and then, if needed, performing a Wheel End Disconnect Position Learn routine. |
| 08-074-25 REV. C | 2025-07-17. Service bulletin. ELECTRICAL SYSTEM. RSU With Additional Sleep Cycles for HV Battery Integrity Check - Flash: Electronic Vehicle Control Unit (EVCU) Updates 11A2 Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● C10FA-00 - Wheel Hub disconnect Actuator Performance Left. ● C10FB-00 - Wheel Hub disconnect Actuator Performance Right. ● C10F8-00 - Left Front Wheel Hub Disconnect Actuator Position Sensor Circuit Range/Performance. ● C10F9-00 - Right Front Wheel Hub Disconnect Actuator Position Sensor Circuit Range/Performance. ● P061B-00 - Internal Control Module Torque Calculation Performance. Customers may also comment on one or more of the following: ● Instrument Panel Cluster (IPC), radio range and charge time estimations and messages are not correct. ● Battery range incorrect. ● Improved battery State of Charge (SoC) accuracy in off-nominal conditions. ● Battery heating values incorrect on radio when on Performance Pages display. ● Charging does not start when plugged in. ● Charging is not indicating when battery is at full charge. ● Charging slow or takes too long. ● Bumps and jerks while accelerating or decelerating. ● Wrench icon is illuminated on the IPC. ● Turtle icon is illuminated on the IPC. ● Vehicle enters into limp home mode. In addition, the following software enhancement is also available: ● Enables compatibility with the Flo V3 Chargers |
| 08-014-25 REV. D | 2025-07-17. Service bulletin. ELECTRICAL SYSTEM. Flash: Electronic Vehicle Control Unit (EVCU) Updates 11A2 Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● C10FA-00 - Wheel Hub disconnect Actuator Performance Left. ● C10FB-00 - Wheel Hub disconnect Actuator Performance Right. ● C10F8-00 - Left Front Wheel Hub Disconnect Actuator Position Sensor Circuit Range/Performance. ● C10F9-00 - Right Front Wheel Hub Disconnect Actuator Position Sensor Circuit Range/Performance. ● P061B-00 - Internal Control Module Torque Calculation Performance. Customers may also comment on one or more of the following: ● Instrument Panel Cluster (IPC), radio range and charge time estimations and messages are not correct. ● Battery range incorrect. ● Improved battery State of Charge (SoC) accuracy in off-nominal conditions. ● Battery heating values incorrect on radio when on Performance Pages display. ● Charging does not start when plugged in. ● Charging is not indicating when battery is at full charge. ● Charging slow or takes too long. ● Bumps and jerks while accelerating or decelerating. ● Wrench icon is illuminated on the IPC. ● Turtle icon is illuminated on the IPC. ● Vehicle enters into limp home mode. In addition, the following software enhancement is also available: ● Enables compatibility with the Flo V3 Chargers. This bulletin involves reprogramming the IDCM, BPCM, MCP A, MCP B and the EVCU with the latest available software and then, if needed, performing a Wheel End Disconnect Position Learn routine. |
| 08-013-25 REV. D | 2025-07-17. Service bulletin. ELECTRICAL SYSTEM. Flash: Motor Control Processor B (MCP B) Updates 11A2 Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): ● P1626-00 - Park Pawl Motor Stuck. Customers may also comment on one or more of the following: ● Wrench lamp on in the Instrument Panel Cluster (IPC). ● Not able to move the shifter out of Park. ● Vehicle has reduced power. This bulletin also includes the following software enhancement: ● Software enhancement to prevent erroneous fault identification resulting in inverter shutdown. This bulletin involves reprogramming the IDCM, BPCM, MCP A, MCP B and the EVCU with the latest available software and then, if needed, performing a Wheel End Disconnect Position Learn routine |
| 08-011-25 REV. C | 2025-07-17. Service bulletin. ELECTRICAL SYSTEM. Flash: Battery Pack Control Module (BPCM) Updates 11A2 Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● P0DE6 - Hybrid/EV Battery Pack Cell Voltage Low. NOTE: Active or stored. ● P1DAF - Incompatible Limp In Action Requested. NOTE: Active or stored. ● P1CDE - Hybrid/EV Wakeup Control 2 Output Circuit Short to Ground. ● P1CDA - Hybrid/EV Wakeup Control 1 Output Circuit/Open. ● U00C6 - Lost Communication With AIR Pressure Sensor. ● P0F00 - Hybrid/EV Battery Module 1 Performance. ● P0F01 - Hybrid/EV Battery Module 2 Performance. ● P0F02 - Hybrid/EV Battery Module 3 Performance. ● P0F03 - Hybrid/EV Battery Module 4 Performance. ● P0F04 - Hybrid/EV Battery Module 5 Performance. ● P0F05 - Hybrid/EV Battery Module 6 Performance. ● P0F06 - Hybrid/EV Battery Module 7 Performance. ● P0F07 - Hybrid/EV Battery Module 8 Performance. ● P0F08 - Hybrid/EV Battery Module 9 Performance. ● P0F09 - Hybrid/EV Battery Module 10 Performance. ● P0F0A - Hybrid/EV Battery Module 11 Performance. ● P0F0B - Hybrid/EV Battery Module 12 Performance. ● P0F0C - Hybrid/EV Battery Module 13 Performance. ● P0CA6-00 - Hybrid/EV Battery Charging Current High. NOTE: If the following DTCs are present/active in the BPCM, Battery Pack replacement will be required. Guided Diagnostics will prompt you for the repair action if the diagnostic is present on the vehicle. ● P0ADB-00 - Hybrid/EV Battery Positive Contractor A Control Circuit Low. ● P0AE2-00 - Hybrid/EV Battery Precharge Contactor Circuit Stuck Closed P0AA1-00 - Hybrid/EV Battery Positive Contactor "A" Stuck Closed. ● P0FF8-00 - Hybrid/EV Battery Precharge Contactor Circuit "B" Stuck Closed. Customers may also comment on one or more of the following: ● Wrench icon is illuminated on the Instrument Panel Cluster (IPC). ● Vehicle will not enter Drive Ready Mode. This bulletin also includes the following software enhancement: ● Bootloader update to prevent battery disconnect unit damage. ● Improvements in detecting pre-existing battery disconnect unit damage. ● Charging related enhancements that may lead to DTC P0CA6 falsely setting This bulletin involves reprogramming the IDCM, BPCM, MCP A, MCP B and the EVCU with the latest available software and then, if needed, performing a Wheel End Disconnect Position Learn routine |
| 08-010-25 REV. D | 2025-07-17. Service bulletin. ELECTRICAL SYSTEM. Flash: Motor Control Processor A (MCP A) Updates 11A2 Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set the following Diagnostic Trouble Code (DTC): ● P1626-00 - Park Pawl Motor Stuck. Customers may also comment on one or more of the following: ● Wrench lamp on in the Instrument Panel Cluster (IPC). ● Not able to move the shifter out of Park. ● Vehicle has reduced power. This bulletin also includes the following software enhancement: ● Software enhancement to prevent erroneous fault identification resulting in inverter shutdown This bulletin involves reprogramming the BPCM, MCP A, MCP B and the EVCU with the latest available software and then performing a Wheel End Disconnect Position Learn routine |
| 08-206-25 | 2025-07-09. Service bulletin. ELECTRICAL SYSTEM. Flash: Electronic Vehicle Control Unit (EVCU) Updates 11A2 Customers may experience a Malfunction Indicator Lamp (MIL) illumination and the vehicle may exhibit/set one or more of the following Diagnostic Trouble Codes (DTCs): ● C10FA-00 - Wheel Hub disconnect Actuator Performance Left. ● C10FB-00 - Wheel Hub disconnect Actuator Performance Right. Customers may also comment on the following: ● Wrench icon is illuminated on the Instrument Panel Cluster (IPC). This bulletin involves reprogramming the EVCU with the latest available software and then, if needed, performing a Wheel End Disconnect Position Learn routine |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.