Service bulletins for the 2016 Jeep Grand Cherokee
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
408 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
Only bulletins with component: Engine are shown. Show all
| S2209000003 | 2023-01-09. Service bulletin. ENGINE; ELECTRICAL SYSTEM:SEAT HEATER:WIRING HARNESS; ELECTRICAL SYSTEM:HAND HEATER:WIRING HARNESS. Complete Engine Assembly Replacements Arriving Without Engine Wiring Harness. |
|---|---|
| 0901116 | 2022-12-19. Service bulletin. ENGINE AND ENGINE COOLING. Engine Oil Pan Replacement This bulletin involves inspecting and possibly replacing the engine oil pan due to oil weepage. The customer may describe that their vehicle has oil weepage. |
| S2209000004 | 2022-12-19. Service bulletin. EQUIPMENT; ENGINE AND ENGINE COOLING. If a Mopar oil filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils. |
| 0900916 | 2022-11-21. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. Re+G21:H21place Both Intake Variable Valve Timing Solenoids This bulletin involves replacing both left and right intake variable valve timing solenoids due to multiple DTCs. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination or the engine runs rough. Upon further investigation the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) set in the PCM: · P0017 - Crankshaft/Camshaft Timing Misalignment - Bank 1 Sensor 2. · P0019 - Crankshaft Position - Camshaft Position Correlation Bank 2 Sensor 2. · P000A - Bank 1 Camshaft 1 Position Slow Response. · P000C - Bank 2 Camshaft 1 Position Slow Response. |
| 9003704 | 2022-10-31. Service bulletin. POWER TRAIN; ENGINE AND ENGINE COOLING. Trans Oil Pan, Heater Tube or O-ring, Heater Applies to vehicles equipped with 8 speed transmissions only; If you have a leak that appears to be at the pan the use of proper leak detection is recommended. The fluid in the 8 speeds can be detected with a black light and there are aftermarket spray on leak detection materials to help ensure that the leak is properly diagnosed and not from another location such as cooler lines, heater tubes, or case porosity. If you have a leak concern please note that the transmission pan gasket is available for many of the 8 speed applications FCA offers. See your parts specialist for the proper gasket for the repair. |
| 1802417 | 2022-10-24. Service bulletin. EXTERIOR LIGHTING; ENGINE AND ENGINE COOLING; FUEL SYSTEM, GASOLINE; BACK OVER PREVENTION; ELECTRICAL SYSTEM. Flash: Powertrain Diagnostic and System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one of the following DTCs have been set:P040B - Exhaust Gas Recirculation Temperature Sensor 1 Circuit Performance(2017 MY with a 3.6L Only). U1424 - Implausible Engine Torque Signal Received(2017 MY Only). P2681 - Engine Coolant Bypass Valve Control Circuit Open(3.6L Only). P2299-00 - Brake Pedal Position/Accelerator Pedal Position Incompatible. B23C3 - Stop/Start Disable Switch 1/2 Correlation(3.0L and 3.6L Only). The following DTCs have been changed from a one trip fault to a two trip fault for(3.0L and 3.6L 2017 MY Only):P0335 - Crankshaft Position Sensor Circuit. P0339 - Crankshaft Position Sensor Intermittent. P0340 - Camshaft Position Sensor Circuit - Bank 1 Sensor 1. P0344 - Camshaft Position Sensor Intermittent - Bank 1 Sensor 1. P0365 - Camshaft Position Sensor Circuit - Bank 1 Sensor 2. P0369 - Camshaft Position Sensor Intermittent - Bank 1 Sensor 2. P0345 - Camshaft Position Sensor Circuit - Bank 2 Sensor 1. P0349 - Camshaft Position Sensor Intermittent - Bank 2 Sensor 1. P0390 - Camshaft Position Sensor Circuit - Bank 2 Sensor 2. P0394 - Camshaft Position Sensor Intermittent - Bank 2 Sensor 2. In addition, customers may experience one of the following conditions:A shorter auxiliary battery life. An illuminated Automatic Oil Change Indication (AOCI) light(3.6L Only). Other enhancements included in this update:Improvements to vehicle driveability during a cam or crank sensor MIL condition(2017 MY Only). Improved knock sensor performance. |
| 52029737 | 2022-10-17. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. TANK, Diesel Exhaust Fluid, Part Includes Temp Sensor and Level Sensor For DS and WK vehicles ONLY; If the urea tank is being replaced due to P249C, P203E, or P24F3 on a 2014-2016 model year 3.0L Turbo Diesel (EXF) on DS or WK, please call Indra Djutrisno at cell (248) 892-3473. If no response is received within 15 minutes, please continue with repair |
| S1809000007 | 2022-10-17. Service bulletin. ENGINE AND ENGINE COOLING. Customer Complaint May Include Engine Oil Leak Or Consumption |
| S1809000007 | 2022-10-17. Service bulletin. ENGINE. Customer Complaint May Include Engine Oil Leak Or Consumption |
| 9003704 | 2022-09-26. Service bulletin. SEATS; FUEL SYSTEM, GASOLINE; AIR BAGS; POWER TRAIN; BACK OVER PREVENTION; ENGINE AND ENGINE COOLING. Transmission Oil Pan, Heater (TMU), Tube or O-ring Applies to vehicles equipped with 8 speed transmissions only; if you have a leak that appears to be at the pan the use of proper leak detection is recommended. The fluid in the 8 speeds can be detected with a black light and there are aftermarket spray on leak detection materials to help ensure that the leak is properly diagnosed and not from another location such as cooler lines, heater tubes, or case porosity. Please note that the transmission pan gasket is available for many of the 8 speed applications FCA offers. Please review the available quick connect and transfer tube parts, as replacement of the TMU may not be required. If a TOC line connection is found to be the source, the quick connect may need replacement. If the leak source is coming from the connection of the TMU to the transmission, the transfer tube may need replacement. When parts are returned to the QEC the retaining clips (snap ring) for the quick disconnect fittings are missing. (This leaves a question as to whether the clips were missing from the assembly plant, or the technician removed them in order to make line removal easier.) Please return the clips with the transmission heater and note if they were not there to begin with. For any questions regarding transmission heater, contact FCA Redacted Content. If no response in 15 minutes, proceed with repair. |
| S2109000004 | 2022-09-26. Service bulletin. ENGINE AND ENGINE COOLING. Issue involves overheating, running hot, coolant leaks and related symptoms after a Mopar replacement engine has been installed in the vehicle. |
| S1709000010RevB | 2022-09-26. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:CRANK/CAMSHAFT POSITION SENSOR; UNKNOWN OR OTHER. Customer complaints may include abnormal engine noise, rough idle, lack of power, misfire. Upon investigation, it may be found that there is excessive camshaft lobe wear/lifter wear (roller failure) on one or more cam lobes and that camshaft/lifter replacement is necessary. |
| 72498 | 2022-09-26. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:CRANK/CAMSHAFT POSITION SENSOR. SAFETY RECALL W58 - LOSS OF CRANK POSITION Overlap with V08/V11/V16 Population |
| S1708000055RevA | 2022-09-26. Service bulletin. ENGINE AND ENGINE COOLING. Overcharging/Undercharging DTC?s Interior And Exterior Lamps Flicker, Electronic Stop/Start (ESS) Operates Intermittently, Crank No Start, Vehicle Will Not Restart After ESS Stop |
| 0901116 | 2022-09-19. Service bulletin. ENGINE AND ENGINE COOLING. Engine Oil Pan Replacement This bulletin involves inspecting and possibly replacing the engine oil pan due to oil weepage. The customer may describe that their vehicle has oil weepage. |
| 1808919 | 2022-09-15. Service bulletin. ENGINE AND ENGINE COOLING. wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK |
| S2109000010 | 2022-09-15. Service bulletin. ENGINE. 3.0L Ecodiesel Engine Oil Information |
| D1522 | 2022-09-15. Service bulletin. ENGINE. Fast Feedback Program |
| D1522RevA | 2022-09-15. Service bulletin. ENGINE. Fast Feedback Program |
| 68142905A | 2022-09-15. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:GAS RECIRCULATION VALVE (EGR VALVE). EGR Temperature Sensor |
| 04-001-21 | 2022-08-22. Service bulletin. ENGINE AND ENGINE COOLING. Pentastar Upgrade Oil Fill Level after an Oil Change This bulletin involves rechecking the oil fill level after filling the engine to the correct specifications. The customer may describe that after an oil change they check their oil fill level and it is showing overfilled on the oil dipstick. |
| 14-008-21 | 2022-08-22. Service bulletin. FUEL SYSTEM, DIESEL; ENGINE AND ENGINE COOLING:ENGINE:CRANK/CAMSHAFT POSITION SENSOR. 3.0L Diesel Crankshaft Tone Wheel Loss of Signal - X95 Warranty Extension This bulletin involves replacing the crankshaft tone wheel. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set :P0335-00 - Crankshaft Position Sensor Circuit. P0336-00 - Crankshaft Position Sensor Performance. Customers may also comment the following:The vehicle will not accelerate quickly over 80 kph (50 mph) (vehicle is in limp mode). This symptom/condition is cause from missing magnetic material on the crankshaft tone wheel |
| S1818000024 | 2022-08-22. Service bulletin. FUEL SYSTEM, GASOLINE; ENGINE AND ENGINE COOLING. Diesel Fuel Injector Cleaning Procedure |
| S2109000010 | 2022-08-22. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:OIL/LUBRICATION: OIL COOLER. 3.0L Ecodiesel Engine Oil Information |
| 68225378A | 2022-08-22. Service bulletin. ENGINE AND ENGINE COOLING. 3.0L V6 Turbo Diesel - Sales Code EXF A crankshaft locking tool marked 630 is installed on all 3.0L EXG long blocks (Lower rear left side of block under starter location). This tool locks the crankshaft at 30? ATDC. Refer to: Valve Timing ? Standard Procedure ? LOCKING ENGINE 30 DEGREE AFTER TDC IN TechCONNECT for further details. This tool must be removed after the the injection pump has been installed on the engine. The tool will be replaced with the engine block plug from the engine being removed. The engine will not turn over with this tool installed.~ |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.