# P0300 on the 2021 Jeep Grand Cherokee L

The bulletins listed name this code in NHTSA's summary, or are about the same components. A bulletin or a recall listed here may apply to the model year. None of it is a diagnosis.

Nobody has written a description of this code yet.

## Bulletins for this model year that name P0300

- [11031455](https://open.wenmarpro.com/bulletins/11031455), 2026-04-22: Flash: Powertrain Control Module \(PCM\) Updates Customers must experience a Malfunction Indicator Lamp \(MIL\) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes \(DTCs\): ● P0300 \- Multiple Cylinder Misfire \- In Active or Stored status set during cold start catalyst heating. ● P0301 \- Cylinder 1 Misfire \- In Active or Stored status set during cold start catalyst heating. ● P0302 \- Cylinder 2 Misfire \- In Active or Stored status set during cold start catalyst heating. ● P0303 \- Cylinder 3 Misfire \- In Active or Stored status set during cold start catalyst heating. ● P0304 \- Cylinder 4 Misfire \- In Active or Stored status set during cold start catalyst heating. ● P0305 \- Cylinder 5 Misfire \- In Active or Stored status set during cold start catalyst heating. ● P0306 \- Cylinder 6 Misfire \- In Active or Stored status set during cold start catalyst heating. Customers may also comment on one or more of the following: ● Check engine illuminates when fueling the vehicle while the engine is running. ● Vehicle has a noticeable misfire. ● Vehicle idles rough. ● Engine noise. NOTE: Noise is heard coming from the valvetrain. In addition, the following software enhancement is available: ● Update to prevent customers from driving their vehicles while the Electric Park Brake \(EPB\) is engaged. Engine torque will be limited to prevent the Rear Drive Unit from being damaged. NOTE: Previously, the EPB would remain engaged without any torque limit which could lead to the Rear Drive Unit being damaged/broken. This bulletin involves reprogramming the PCM with the latest available software.
- [11030229](https://open.wenmarpro.com/bulletins/11030229), 2026-03-25: Flash: Powertrain Control Module \(PCM\) Updates Customers must experience a Malfunction Indicator Lamp \(MIL\) illumination and the vehicle must SYMPTOM: exhibit/set one or more of the following Diagnostic Trouble Codes \(DTCs\): ● \*\*P0111\-00 \- Intake Air Temperature Sensor 1 Circuit Range Performance Bank 1. \(In Active or Stored status\) ● P0071\-00 \- Ambient Air Temperature Sensor Performance. \(In Active or Stored status\) ● P0072\-00 \- Ambient Air Temperature Sensor Circuit "A" Low. \(In Active or Stored status\) ● P0073\-00 \- Ambient Air Temperature Sensor Circuit "A" High. \(In Active or Stored status\) ● P0011\-00 \- Bank 1 Camshaft 1 Position Timing Over Advanced Or. \(In Active or Stored status\) ● P25E4\-00 \- B Camshaft Position \- Unable To Achieve Locked Position Bank 1. \(In Active or Stored status\) ● P05BD\-00 \- Stop\-Start Mode Switch Range/Performance. \(In Active or Stored status\) ● P0116\-00 \- Engine Coolant Temperature Sensor 1 Performance. \(In Active or Stored status\) ● P062B\-00 \- Internal Control Module Fuel Injector Control Performance. \(In Active or Stored status\) ● P0604\-00 \- Internal Control Module Random Access Memory Ram Error. \(In Active or Stored status\) ● P060C\-00 \- Internal Control Module Main Processor Performance. \(In Active or Stored status\)\*\* ● P018B\-00 \- Fuel Pressure Sensor "B" Circuit Range/performance. \*\*\(In Active or Stored status\)\*\* ● P1CEA\-00 \- Boost Side EVAP Purge System Performance. \*\*\(In Active or Stored status\)\*\* ● P06DD\-00 \- Engine Oil Pressure Control Circuit Performance/Stuck Off. \*\*\(In Active or Stored status\)\*\* ● P00C6\-00 \- Fuel Rail Pressure Too Low \- Engine Cranking. \*\*\(In Active or Stored status\)\*\* ● P0300\-00 \- Multiple Cylinder Misfire. \*\*\(In Active or Stored status\)\*\* Customers may also experience one or more of the following: ● \*\*Oil Level High Warning in the Instrument Panel Cluster \(IPC\).\*\* ● Fully Autonomous Parking Assist \(FAPA\) is not deactivated when accelerator pedal is pressed. ● Vehicle is not heating up fast enough at freezi