Service bulletins for the 2015 Jeep Cherokee
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
613 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
| 0803316REVA | 2022-12-19. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.; EQUIPMENT. RA4 RG4 RJ4 Radio Enhancements |
|---|---|
| 2400716 | 2022-12-19. Service bulletin. VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM; ELECTRICAL SYSTEM. Flash: HVAC System Enhancement This bulletin involves reprogramming the HVAC control module with the latest available software. The customer may describe one of the following: · **The radio temperature display does not match the HVAC controller temperature display. · After a temperature slide bar movement, the radio display shows the temperature slider waiting for about three seconds and then the slide bar jumps again. · Insufficient heating or cooling inside the vehicle.** · After the ignition has been turned off for over four minutes, the MTC HVAC controls change to a different setting. The temperature setting should remain where the temperature was last set at. When the temperature slider bar is left at mid way point or less, the setting will revert to a cooler setting depending on where it was set before. |
| 1800416REVA | 2022-12-19. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN; ENGINE AND ENGINE COOLING. Flash: 2.4L Powertrain Diagnostic And System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find one or more of the following DTCs: 2015 KL Only · **P0335 - Crankshaft Position Sensor Circuit.** · P0456 - EVAP System Small Leak. · P0300 - Multiple Cylinder Misfire. · P0301 - Cylinder 1 Misfire. · P0302 - Cylinder 2 Misfire. · P0303 - Cylinder 3 Misfire. · P0304 - Cylinder 4 Misfire. · P2610 - PCM Internal Engine Off Timer Performance. · P1607 - PCM Internal Shutdown Timer Rationality. · U0402 - Implausible Data Received From TCM (ED6). · P0116 - Engine Coolant Temperature Sensor 1 Performance. · P050D - Cold Start Rough Idle. · P2172 - High Airflow/Vacuum Leak Detected. · P219A - Air-Fuel Ratio Cylinder Imbalance Bank 1 has been set in the PCM. 2014 KL Only · P2172 - High Airflow/Vacuum Leak Detected. · P219A - Air-Fuel Ratio Cylinder Imbalance Bank 1 has been set in the PCM. · P106A - Cylinder 3 Oil Supply Solenoid Valve Switch Off Time Out Of Range. · P2251 - O2 Sensor 1/1 Negative Current Control Circuit Open. · P0031 - O2 Sensor 1/1 Heater Circuit Low. In addition, some customers may experience one or more of the following conditions: · Cold Engine Startup Flare and Idle Surge (ED6). · Intermittent elevated engine RPM at start up. · Less than desired gear engagement in lower ambient temperatures. · Less than desired idle performance. |
| 68175510A | 2022-12-19. Service bulletin. SUSPENSION. Rear trailing arm/link. Customer noise issue due to loose trailing link If a trailing link is damaged or noisy, please call Steve Lin at Cell 909-569-5117 prior to removing the part. If you do not hear from us within 15 minutes please continue with the repair. |
| 68141352A | 2022-12-19. Service bulletin. ENGINE AND ENGINE COOLING. 3.2L - 3.6L Cylinder Head Assy Multiple cylinder head replacement. If cylinder head is replaced on a vehicle more than 1 time for any reason, please call any of the following people.~ First: Ron Dallison ? Cell (248) 292-9510 Ron.dallison@fcagroup.com ~ Second: Joe Lovell - Cell (734) 309-6467 joe.lovell@fcagroup.com~ If a response is not received within 15 mins, then proceed with the necessary repair.~ |
| S2209000004 | 2022-12-19. Service bulletin. EQUIPMENT; ENGINE AND ENGINE COOLING. If a Mopar oil filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils. |
| 2302716 | 2022-11-21. Service bulletin. SEATS; STRUCTURE. Rattle/Squeak From Lower Rear Seat This bulletin involves inspecting the rear seat track adjuster bar speed nut fasteners. The customer may describe a rattling/ticking noise from rear seat track(s)/seat track adjuster bar area. |
| 3100122 | 2022-10-31. Service bulletin. STRUCTURE. Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components. |
| 3100122 | 2022-10-31. Service bulletin. STRUCTURE:INTERIOR PANELS:DOOR; STRUCTURE; UNKNOWN OR OTHER. Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components. |
| 9003783 | 2022-10-31. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION; STRUCTURE. Shifter - Automatic Transmission If a 2015 - 18MY KL ONLY is brought in with a ?Service Shifter? message on the cluster and/or the following DTCs are present indicating loss of communication with the shifter: U0103, U0103-87. Prior to beginning any repair, please call John Zbranchik at 248-576-0756 or Pablo Flores at 248-576-3972. If no reply contact Dil Weerasinha at 248-944-5967 or Jay Nagle 248-576-5657. If you are unable to contact any of the above, and all the DTCs related to loss of comm are STORED, first perform a vehicle scan with a wiTECH tool or similar and email the log to john.zbranchik@fcagroup.com and pablo.flores1@fcagroup.com. Ensure all stored DTCs in the vehicle are recorded in the log. Use the tool to clear all codes and ensure the ?Service Shifter? message does not return. If this is the first occurrence of this issue on this vehicle, do NOT replace the shifter at this time. If any DTCs related to loss of comm with the shifter are ACTIVE, a full bus log is highly desired. Please contact a regional tech representative to acquire this log. After the log is acquired, or if this is not feasible, check for loose/bent pins, spread terminals on both the male pin cavity in the shifter and the female connector from the body harness take out and all grounds. If no issues are found, replace the shifter and return it to the Quality Engineering Center (QEC). |
| 9003663 | 2022-10-31. Service bulletin. VISIBILITY:POWER WINDOW DEVICES AND CONTROLS. Side Window Air Deflectors There is a new (side window) deflector kit P/N released for Cherokee. P/N 82215206 is coded with usage on black trim models (sales code +MMF). Kit P/N for "bright" trim usage should be 82213940AB (sales code +MMP). Please make sure parts personnel understand the distinction between the 2 different applications before ordering. |
| 9003789 | 2022-10-31. Service bulletin. EQUIPMENT; STRUCTURE. KL Gear Shift Module For 2015-2018 KL ONLY, if vehicle DTC Code P1C86-1D (PRNDL Display Current out of Range) is verified as either stored or active please contact Pablo Flores in FCA Chassis Engineering at cell (248) 979-7062. If no response in 15 minutes, proceed with repair. For additional repair see NOTES below: NOTE 1: If DTC P1C86-1D is still active after inspecting harness connections from Service Procedure (STEP 2). DO NOT replace SHIFTER ASSEMBLY. Instead, replace PRNDM bezel only. NOTE 2: After replacing PRNDL Assembly, clear DTCs and check to confirm DTC does not return. Please return parts back to FCA Engineering if PRNDM is deemed non-functional after performing this Tech Tip. For 2015-2018 KL ONLY; If vehicle DTC Code P1C86-1D (PRNDL Display Current out of Range) is verified as either stored or active please contact Pablo Flores in FCA Chassis Engineering at cell (248) 979- 7062. If no response in 15 minutes, proceed with repair. For additional repair see NOTES below: NOTE 1: If DTC P1C86-1D is still active after inspecting harness connections from Service Procedure (STEP 2). DO NOT replace SHIFTER ASSEMBLY. Instead, replace PRNDM bezel only. NOTE 2: After replacing PRNDL Assembly, clear DTCs and check to confirm DTC does not return. Please return parts back. |
| T12 | 2022-10-31. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL. Customer Satisfaction Notification T12 VECI Label The Vehicle Emission Control Information (VECI) label on about 120,000 of the above vehicles may be missing emission control information. The VECI label is often used during in-use Inspection and Maintenance (I/M) testing to verify proper emissions related components. Incorrect VECI label information could result in denial of vehicle registration for the vehicle in the state of California. A new VECI label must be installed. |
| 68264880A | 2022-10-31. Service bulletin. EQUIPMENT. Parts. |
| 2101417 | 2022-10-24. Service bulletin. POWER TRAIN. Flash: Transmission Diagnostic and Shift Enhancements AN-K4-21-20170811 Refer to China Joint Venture (JV) released document AN-K4-21-20170811, for details on this service action. |
| 9003579 | 2022-10-24. Service bulletin. ELECTRICAL SYSTEM; AIR BAGS. Occupant Restraint Controller (ORC) For PF, KL or UF Vehicles ONLY: Prior to replacing ORC part numbers, please contact FCA engineering if ANY of the following Diagnostic trouble codes are Stored or Active in the ORC module: DTC: B223D-00 - OCM DTC Present DTC: B0050-13 - Driver Seatbelt Sensor-Circuit Open DTC: B0052-13 - Passenger Seatbelt Sensor-Circuit Open DTC: B00B5-13 - Driver Seat Track Position Restraints Sensor-Circuit Open DTC: B00C5-13 - Passenger Seat Track Position Restraints Sensor-Circuit Open DTC: B0028-13 - Right Side Seat Deployment Squib 1-Circuit Open DTC: B0020-13 - Left Side Seat Deployment Squib 1-Circuit Open Execute DealerCONNECT / TechCONNECT Diagnostic Procedures to assess potential defects to devices connected to the ORC Module depending on the active or stored Diagnostic Trouble Code. If no defects are detected, verify wiring connectivity between the ORC Module and the component associated with the Diagnostic Trouble Code. Investigate connector pins and wire harness terminals for bent,corroded,or spread conditions. If no response within 15 minutes, proceed with repair. FCA Engineering Contacts: Jay Nagle (ORC Module, Driver/passenger seat track position sensor, OCM for PF, KL or UF Vehicles ONLY) @ cell (248) 576-5657 |
| S13 | 2022-10-24. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. Flat Tow Owner Addendum Card |
| 2301516 | 2022-10-24. Service bulletin. STRUCTURE. Water On Front Carpet Or In Rocker Side Sill This bulletin involves visually inspecting the sealer on the engine bulkhead area and water testing to diagnose leak path. Then repairing body seam leaks with sealer. The customer may describe damp or wet carpet in the front footwell or in the rocker sill. This condition is primarily found on the left side but may be on the right (Fig. 1) or both footwells. The cause of this leak may be due to a sealant void on the body seam, allowing water to enter the vehicle interior. |
| 2301516REVA | 2022-10-24. Service bulletin. STRUCTURE. Water On Front Carpet Or In Rocker Side Sill This bulletin involves visually inspecting the sealer on the engine bulkhead area and water testing to diagnose leak path. Then repairing body seam leaks with sealer. The customer may describe damp or wet carpet in the front footwell or in the rocker sill. This condition is primarily found on the left side but may be on the right (Fig. 1) or both footwells. The cause of this leak may be due to a sealant void on the body seam, allowing water to enter the vehicle interior. |
| 0802216 | 2022-10-24. Service bulletin. EQUIPMENT. Accessory Kit to Enhance Flat Tow Performance The customer may describe that their vehicle shakes or bounces while being flat towed. Only perform this repair procedure if the customer?s VIN is listed in VIP or your RRT VIN list. Using a Scan Tool (wiTECH) with the appropriate Diagnostic Procedures available in TechCONNECT, verify all engine systems are functioning as designed. If DTCs or symptom conditions, other than the ones listed above are present, record the issues on the repair order and repair as necessary before proceeding further with this bulletin. |
| 23-015-16 | 2022-10-24. Service bulletin. STRUCTURE. Water On Front Carpet Or In Rocker Side Sill This bulletin involves visually inspecting the sealer on the engine bulkhead area and water testing to diagnose leak path. Then repairing body seam leaks with sealer. The customer may describe damp or wet carpet in the front footwell or in the rocker sill. This condition is primarily found on the left side but may be on the right (Fig. 1) or both footwells. The cause of this leak may be due to a sealant void on the body seam, allowing water to enter the vehicle interior. |
| 21-013-16 | 2022-10-24. Service bulletin. POWER TRAIN. 948TE 9 Speed Transmission Quick Learn Procedure This bulletin provides information on how to perform the new scan tool based transmission Quick Learn procedure. This procedure is required after certain transmission repairs or to improve a customer?s concern of poor shift quality. Customers may indicate that their transmission shift quality may be erratic. |
| 18-035-16 | 2022-10-24. Service bulletin. BACK OVER PREVENTION; ELECTRICAL SYSTEM; POWER TRAIN; ENGINE AND ENGINE COOLING; EXTERIOR LIGHTING. Flash: Powertrain Diagnostic And System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: · **P1D83 - Implausible Engine Oil Temperature Signal Received.** · P0456 - EVAP System Small Leak. · P0335 - Crankshaft Position Sensor Circuit. · U0402 - Implausible Data Received From TCM - (Transmission Control Module).** · B10EA - Blower Motor Control Circuit High. · B10E9 - Blower Motor Control Circuit Low. · P0441 - EVAP Purge System Performance. · P0116 - Engine Coolant Temperature Sensor Performance. · P2067 - Fuel Level Sensor 2 Circuit Low (International Only). In addition the customer may notice one of the following conditions: · **A push sensation when the transmission is downshifting from eighth to seventh gear.** · Vehicle shudder at stop/start with A/C on. |
| 08-039-16 | 2022-10-24. Service bulletin. ELECTRICAL SYSTEM; EXTERIOR LIGHTING; POWER TRAIN; STEERING. Harness Repair Or Replacement For No Start Or Stiff Steering This bulletin involves inspecting the wire harness and installing mastic patch. If rub through is visible replace wire harness. A small number of customers may experience a no start condition, stiff steering or a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs): · U0131 - Lost Communication With Power Steering Control Module. · U0100-00 - Lost Communication With ECM/PCM. · P0512-00 - Starter Request Circuit. |
| 08-038-16 | 2022-10-24. Service bulletin. PARKING BRAKE; ELECTRICAL SYSTEM. Flash: Electronic Parking Brake Module Enhancement This bulletin involves updating the Electronic Parking Brake (EPB) module software. The customer may describe the EPB does not engage with the ?Auto Apply? feature selected. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.