WenmarOpen by Wenmar Pro

Service bulletins for the 2009 GMC Sierra

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

1723 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Driver assistance are shown. Show all

Bulletins, newest first
PI0639B2018-06-04. Service bulletin. ELECTRONIC STABILITY CONTROL (ESC); EQUIPMENT. This preliminary informational bulletin provides a revision of PI0639B to add the 2013 model year and update the labor operation information.
080730026D2018-05-07. Service bulletin. ELECTRONIC STABILITY CONTROL (ESC). This informational bulletin provides information on Some vehicles may rock or move slightly forward or rearward while in Park at start up after cold soak. This condition may be accompanied by a clunk noise. This is a slight movement that is more often seen visually, rather than felt, when viewed from the outside and using the auto-start feature, if equipped.
10-00-89-006C2018-04-16. Service bulletin. BACK OVER PREVENTION: SENSING SYSTEM: RADAR. This informational bulletin provides directions on submitting different PIRs
PIP5168F2018-02-21. Service bulletin. POWER TRAIN:AXLE ASSEMBLY:AXLE SHAFT; BACK OVER PREVENTION; FUEL SYSTEM, GASOLINE. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a no crank concern. Technician will need to check the valve train for movement when the engine is cranked. If the valve train is not moving while the crankshaft is moving the front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the valve train is rotating during inspection, disconnect the Camshaft Position sensor and check if the engine will start. If the engine starts front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly. If the engine does not start with the Camshaft Position sensor disconnected the follow published “Engine Cranks But Does Not Run” diagnosis in Service Information. Also perform an Engine Compression Test and Cylinder Leakage Test in Service Information documents all results. If the Service Information procedures above isolate an engine mechanical concern then removed to inspect for a sheared cam sprocket locator pin. If the cam sprocket locator pin has sheared, replace the engine assembly.
PIT5209A2017-12-22. Service bulletin. ELECTRICAL SYSTEM; BACK OVER PREVENTION: BACK-UP ALARM; BACK OVER PREVENTION; STRUCTURE. This Preliminary Information communication provides information to the technician about vehicles that for no reason the alarm will go active. Technician will need to use a scan tool to verify that the alarm was activated by the inclination sensor. If the trigger is the inclination sensor, inspect the sensor's mounting location. Technician will need to relocate the sensor if it is attached to the driver's side lower Heater-Vent-Air Conditioning duct. Technician will need to reinstall the sensor to the top of the Body Control Module bracket.
PIT4322G2017-08-15. Service bulletin. ELECTRONIC STABILITY CONTROL:AUTOMATIC (ASC); TRACTION CONTROL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that have an unwanted Stability Activation and/or a Service Stability message on the Driver Information Center. Technician may find a Diagnostic Trouble Code C0710. Technician should inspect for vehicles modifications before any in-depth diagnostics are performed.
10-08-98-002A2017-08-15. Service bulletin. FORWARD COLLISION AVOIDANCE. This information bulletin explains the use of drilling high strength steel in a collision repair and the GM recommended CryoCobalt Drill bit.
PIT4551E2017-08-15. Service bulletin. EQUIPMENT:ELECTRICAL; BACK OVER PREVENTION: BACK-UP ALARM. This Preliminary Information communication provides information to the technician that during the Pre-Delivery Inspection it may be noticed that the backup alarm is inoperative. Technician can locate the wire harness on the right rear of the frame. Technician can route the harness up and over the spare tire hoist tube and connect to the backup alarm.
PIT4551E2016-04-26. Service bulletin. BACK OVER PREVENTION: CAMERA SYSTEM. SUMMARY TO BE PROVIDED ON A FUTURE DATE.
PIT-5120-A2012-11-29. Service bulletin. ELECTRONIC STABILITY CONTROL:AUTOMATIC (ASC); TRACTION CONTROL SYSTEM; ELECTRONIC STABILITY CONTROL (ESC). GMC/CHEVROLET/CADILLAC: INSTRUMENT PANEL MESSAGES REGARDING STABILITRAK MESSAGE, TRACTION CONTROL MESSAGE, SERVICE BRAKE SYSTEM MESSAGE, IS OFF AND GAUGES, IN VARIOUS MODULES LOW SPEED SETTINGS, ARE INOPERATIVE. MODELS 2007-13 ALL ESCALADES; AVALANCHE, SILVERADO, SUBURBAN, TAHOE; SIERRA, ALL YUKONS AND DENALIS. *PE
PIT-4322-D2011-06-01. Service bulletin. ELECTRONIC STABILITY CONTROL:AUTOMATIC (ASC); SUSPENSION; STEERING. GM: THERE IS UNWANTED STABILITY ACTION OR STABILITY LIGHT ON. THIS CAN BE CAUSED BY THE SUSPENSION BEING MODIFIED. *RM UPDATED 6/18/12. *PE MODELS 2007-13 ALL ESCALADE; AVALANCHE, SILVERADO, SUBURBAN, TAHOE; SIERRA, SIERRA DENALI, ALL YUKONS. UPDATED 11/28/12. *PE UPDATED 4/1015. *PE
PIT-49972010-11-17. Service bulletin. ELECTRONIC STABILITY CONTROL (ESC). CHEVROLET/GMC: TRAC OFF AND SERVICE STABILITRAK MESSAGE WITH DTC C0900. IF THE VEHICLE IS DRIVEN AGGRESSIVELY IMMEDIATELY AFTER A COLD START, WOULD RECEIVE A TRAC OFF AND SERVICE STABILITRAC MESSAGE. THIS CONCERN MAY ALSO OCCUR IF THE ENGINE IS IMMEDIATELY FREE REVV 1/2 THROTTLE OR MORE AFTER A COLD START. *PE
PIT-4665A2009-03-20. Service bulletin. ELECTRONIC STABILITY CONTROL (ESC); EQUIPMENT:ELECTRICAL; ELECTRICAL SYSTEM; ELECTRICAL SYSTEM:SOFTWARE. GENERAL MOTORS: DURING NORMAL DIAGNOSTICS AND/OR REPAIR VERIFICATION THE ABS LIGHT, TRACTION CONTROL AND/OR STABILITRAK INDICATORS MAY BE ON WITH NO DTC'S DISPLAYED BY THE EBCM. *PE UPDATED 11/17/10. *PE UPDATED 3/14/11. *PE
43222008-01-30. Service bulletin. ELECTRONIC STABILITY CONTROL:AUTOMATIC (ASC). UNWANTED STABILITY ACTIVATION AND/OR C0710 WITH LIFT/LOWER KITS-DIFFERENT TIRES/WHEEL. WITH RPO JL4. *NJ UPDATED 12/18/08. *PE
PIT 41622007-09-20. Service bulletin. ELECTRONIC STABILITY CONTROL:AUTOMATIC (ASC). SERVICE STABILITY LAMP DTC C0131. *NJ UPDATED 4/1/08. *NJ UPDATED 6/26/08. *NJ UPDATED 12/18/08. *PE UPDATED 8/1/11. *PE

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.