Service bulletins for the 2004 GMC Canyon
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
602 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
Only bulletins with component: Engine are shown. Show all
| PIP4581B | 2018-06-04. Service bulletin. ENGINE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV); EQUIPMENT. This Preliminary Information communication provides information to the technician about vehicles that may have an engine rattle that star after the engine was repaired ant the repair required the crankshaft balancer removal and replacement. When the rattle noise is duplicated without the Service Engine Soon Malfunction Indicator Lamp and Service Information diagnosis does not isolate the cause the crankshaft balancer bolt should be re-torqued per the specifications states in Service Information. When the rattle noise is duplicated with the Service Engine Soon Malfunction Indicator Lamp and Diagnostic Trouble Code P0016 or P0017 and Service Information diagnosis does not isolate the cause the crankshaft balancer bolt should be re-torqued per the specifications states in Service Information. If tightening the bolt repairs the rattle noise but the Diagnostic Trouble Code P0016 or P0017 continue to set technician should follow published Service Information diagnostics for the Diagnostic Trouble Code. If Service Information diagnostics for the Diagnostic Trouble Code do not lead to a repair for the Diagnostic Trouble Code remove the crankshaft timing sprocket and inspect the crankshaft alignment pin and the related groove of the sprocket for obvious wear. If wear is present replace the sprocket and pin and retest. |
|---|---|
| PIP4945B | 2018-06-04. Service bulletin. ELECTRICAL SYSTEM:STARTER ASSEMBLY:SOLENOID; ENGINE. This Preliminary Information communication provides information to the technician about vehicles that may have Service Engine Soon Malfunction Indicator Lamp on. Technician may find a Diagnostic Trouble Code P0017 may be set current or history. Technician will need to follow published Service Information and all technical services bulletins for Diagnostic Trouble Code P0017. If Service Information diagnostics do not lead to a resolution to the concern there six other reasons Diagnostic Trouble Code P0017 can be set. First the tech should check the timing of the engine. Second issue may be a crank timing gear has a loose fit to the crank follow the current version of PIP3694. The third issue may be the crank end play is excessive see the current version of PIP3694. The forth issue is the cam actuator solenoid is restricted or screens are missing, see current version of PIP3694. The fifth concern may be a cam actuator is sticking, check the current version of PIP4913. And the sixth concern could be low oil pressure or oil contamination, refer to the current version of PIP4913. |
| 060601010D | 2018-06-04. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR. This informational bulletin explains how the catalytic converters may need an inspection, cleaning or replacement if debris have entered the exhaust system. |
| 08-06-01-006D | 2018-06-04. Service bulletin. ENGINE AND ENGINE COOLING; EQUIPMENT. This informational bulletin provides information for Engine Squealing Type Noise on Start-up or Vibration Condition. |
| 00-06-01-012E | 2018-05-21. Service bulletin. ENGINE AND ENGINE COOLING; EQUIPMENT. This information bulletin provides the technician the information on how to properly clean a metal surface using the correct tool. |
| PIP5163C | 2018-05-21. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure. |
| PIP5232A | 2018-05-07. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR. This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire. |
| PIP5232 | 2018-05-07. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR. This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire. |
| PIP5226B | 2018-02-21. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings. |
| PIP5540A | 2018-02-21. Service bulletin. ENGINE. This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance. |
| PIP5232B | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR. This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire. |
| PIT4943D | 2017-08-15. Service bulletin. FUEL SYSTEM, GASOLINE; FUEL SYSTEM, OTHER:STORAGE:TANK ASSEMBLY; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay. |
| PIP5163B | 2017-08-15. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; FUEL SYSTEM, GASOLINE; ENGINE. This Preliminary Information communication provides information to the technician about engine block that have a possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, an out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure. |
| PIP5029F | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon an upper engine and valve cleaning should be performed. |
| PIP5232C | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR. This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the coil grounds ring terminal at the engine block for the bank with the concern and repair the wire. |
| 06-06-01-010B | 2017-08-15. Service bulletin. EQUIPMENT:MECHANICAL; ENGINE AND ENGINE COOLING. This informational bulletin provides information on close-coupled converter and engine replacement. |
| PIP5029H | 2017-08-15. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about vehicles that have a Malfunction Indicator Lamp on or engine misfire, rough idle, extended crank, or crank no start in some cases. Technician will need to perform published Service Information diagnostics. If technician finds carbon, an upper engine and valve cleaning should be performed. Update added part numbers for the cleaner and model years. |
| PIP5098 | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. This Preliminary Information communication provides information to the technician about vehicles that have a "Service 4 Wheel Drive" message displayed in the Driver Information Center. Technician may find Diagnostic Trouble Code C0327 set in the Transfer Case Control Module. Technician will need to inspect circuit 550 ground circuit for the transfer case encoder motor channel circuits. |
| PIT3173C | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician that fluid contamination may be directed to one of the following testing centers according to the type of fluid needing testing. Dealer should send the correct fluid to the proper testing center. |
| PIP4409E | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE. This Preliminary Information communication provides information to the technician about vehicles the have a Service Engine Soon Malfunction Indicator Lamp on and or engine running rough. Technician may find Diagnostic Trouble Codes P0106, P0107, P0171, P0300, P0502, P1107, and P2431. Technician will need to inspect all Manifold Absolute Pressure sensor circuits for being broken inside of the insulation near the Manifold Absolute Pressure sensor connector. |
| PIP5163 | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure. |
| 06-06-01-010C | 2017-08-15. Service bulletin. ENGINE. This informational bulletin provides information on close coupled converters and there affect on newly installed engines or engines during there break in period. |
| PIP5226 | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings. |
| PIP5163A | 2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING. This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure. |
| PIP5029G | 2017-05-16. Service bulletin. ENGINE. THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT HAVE A MALFUNCTION INDICATOR LAMP ON OR ENGINE MISFIRE, ROUGH IDLE, EXTENDED CRANK, OR CRANK NO START IN SOME CASES. TECHNICIAN WILL NEED TO PERFORM PUBLISHED SERVICE INFORMATION DIAGNOSTICS. IF TECHNICIAN FINDS CARBON, AN UPPER ENGINE AND VALVE CLEANING SHOULD BE PERFORMED. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.